diff --git a/scripts/Murax/iCE40-hx8k_breakout_board/README.md b/scripts/Murax/iCE40-hx8k_breakout_board/README.md
new file mode 100644
index 0000000..62078a3
--- /dev/null
+++ b/scripts/Murax/iCE40-hx8k_breakout_board/README.md
@@ -0,0 +1,84 @@
+This example is for the
+[Lattice iCE40HX-8K Breakout Board](http://www.latticesemi.com/Products/DevelopmentBoardsAndKits/iCE40HX8KBreakoutBoard.aspx).
+
+An image of this board is shown below;
+![img/iCE40HX8K-breakout-revA.png]
+
+This board can be purchased for ~$USD 49 directly from Lattice and is supported
+by the IceStorm
+[`iceprog`](https://github.com/cliffordwolf/icestorm/tree/master/iceprog) tool.
+
+
+# Using the example
+
+## Before Starting
+
+Before starting make sure that your board is configured for `CRAM Programming`
+mode. This requires removing jumper `J7` and putting the pair of jumpers on
+`J6` to be parallel to the text on the board.
+
+This is shown in **Figure 5** of the
+[iCE40HX-8K Breakout Board User Guide](http://www.latticesemi.com/view_document?document_id=50373).
+which is also reproduced below;
+![img/cram-programming-config.png]
+
+Once your board is ready, you should follow the setup instructions at the
+[top level](../../../README.md).
+
+You should make sure you have the following tools installed;
+ * Yosys
+ * arachne-pnr
+ * icestorm tools (like icepack and iceprog)
+ * riscv toolchain
+ * sbt
+
+## Building
+
+You should be able to just type `make compile` and get output similar to this;
+```
+...
+  place time 10.14s
+route...
+  pass 1, 15 shared.
+  pass 2, 4 shared.
+  pass 3, 1 shared.
+  pass 4, 0 shared.
+
+After routing:
+span_4     4406 / 29696
+span_12    951 / 5632
+
+  route time 9.12s
+write_txt bin/toplevel.asc...
+icepack bin/toplevel.asc bin/toplevel.bin
+```
+
+The process should take around 30 seconds on a reasonable fast computer.
+
+## Programming
+
+After building you should be able to run `make prog`. You may need to run `make
+sudo-prog` if root is needed to access your USB devices.
+
+You should get output like the following;
+```
+iceprog -S bin/toplevel.bin
+init..
+cdone: high
+reset..
+cdone: low
+programming..
+cdone: high
+Bye.
+```
+
+After programming the LEDs at the top of the board should start flashing in an
+interesting pattern.
+
+## Connect
+
+After programming you should be able to connect to the serial port and have the
+output echoed back to you.
+
+On Linux you can do this using a command like `screen /dev/ttyUSB1`. Then as
+you type you should get back the same characters.
diff --git a/scripts/Murax/iCE40-hx8k_breakout_board/img/cram-programming-config.png b/scripts/Murax/iCE40-hx8k_breakout_board/img/cram-programming-config.png
new file mode 100644
index 0000000..48562bb
Binary files /dev/null and b/scripts/Murax/iCE40-hx8k_breakout_board/img/cram-programming-config.png differ
diff --git a/scripts/Murax/iCE40-hx8k_breakout_board/img/iCE40HX8K-breakout-revA.png b/scripts/Murax/iCE40-hx8k_breakout_board/img/iCE40HX8K-breakout-revA.png
new file mode 100644
index 0000000..2c460bb
Binary files /dev/null and b/scripts/Murax/iCE40-hx8k_breakout_board/img/iCE40HX8K-breakout-revA.png differ