diff --git a/docs/building-examples.rst b/docs/building-examples.rst
index 835865e..3e7b0e2 100644
--- a/docs/building-examples.rst
+++ b/docs/building-examples.rst
@@ -9,7 +9,7 @@ set it to earlier, for example:
 
    export INSTALL_DIR=~/opt/symbiflow
 
-Select your fpga family:
+Select your FPGA family:
 
 .. tabs::
 
@@ -27,7 +27,7 @@ Select your fpga family:
 
          FPGA_FAM="eos-s3"
 
-Next, prepare the enviroment:
+Next, prepare the environment:
 
 .. code-block:: bash
    :name: conda-prep-env
@@ -35,7 +35,7 @@ Next, prepare the enviroment:
    export PATH="$INSTALL_DIR/$FPGA_FAM/install/bin:$PATH";
    source "$INSTALL_DIR/$FPGA_FAM/conda/etc/profile.d/conda.sh"
 
-Finally, enter your working Conda enviroment:
+Finally, enter your working Conda environment:
 
 .. code-block:: bash
    :name: conda-act-env
diff --git a/docs/getting-symbiflow.rst b/docs/getting-symbiflow.rst
index cedfe6b..1bc0658 100644
--- a/docs/getting-symbiflow.rst
+++ b/docs/getting-symbiflow.rst
@@ -1,8 +1,8 @@
 Getting SymbiFlow
 =================
 
-This section describe how to install SymbiFlow and setup a fully working
-enviroment to later build example desings.
+This section describes how to install SymbiFlow and set up a fully working
+environment to later build example designs.
 
 Prerequisites
 -------------
@@ -98,7 +98,7 @@ Select your target FPGA family:
 
          export FPGA_FAM=eos-s3
 
-Next, setup Conda and your system's enviroment:
+Next, setup Conda and your system's environment:
 
 .. code-block:: bash
    :name: conda-setup
@@ -130,7 +130,7 @@ Download architecture definitions:
 
          wget -qO- https://quicklogic-my.sharepoint.com/:u:/p/kkumar/EWuqtXJmalROpI2L5XeewMIBRYVCY8H4yc10nlli-Xq79g?download=1 | tar -xJ -C $INSTALL_DIR/eos-s3/
 
-If the above commands exited without errors, you have successfuly installed and configured your working enviroment.
+If the above commands exited without errors, you have successfully installed and configured your working environment.
 
 Build Example Designs
 ---------------------
diff --git a/docs/running-examples.rst b/docs/running-examples.rst
index 400eae7..eeb6e36 100644
--- a/docs/running-examples.rst
+++ b/docs/running-examples.rst
@@ -1,7 +1,7 @@
 Running example designs
 ========================
 
-This section desribes how to properly connect your board.
+This section describes how to properly connect your board.
 It also helps you configure and run any other software that is necessary to observe results.
 
 Connecting development boards
@@ -10,7 +10,7 @@ Connecting development boards
 Arty board
 ~~~~~~~~~~
 
-#. Connect the board to your computer using the USB cable:
+#. Connect the board to your computer using the USB cable
 #. Connect the board to your computer using the Ethernet cable
    (only if you want to test the LiteX Linux Example)
 
@@ -151,7 +151,7 @@ Prepare SD card
 
 #. Format the SD card by following the `official guide <https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/18842385/How+to+format+SD+card+for+SD+boot>`_.
 
-#. Download and extract pre-built U-boot images
+#. Download and extract pre-built U-boot images:
 
    .. code-block:: bash
 
@@ -160,21 +160,21 @@ Prepare SD card
       wget -qO- https://github.com/SymbiFlow/symbiflow-xc7z-automatic-tester/releases/download/v1.0.0/uboot-linux-images.zip | bsdtar -xf-
       popd
 
-#. Copy U-boot images to the boot mountpoint
+#. Copy U-boot images to the boot mountpoint:
 
    .. code-block:: bash
 
       cp uboot-linux-images/boot/* /path/to/mountpoint/boot/
       sync
 
-#. Copy Arch Linux to the root mountpoint
+#. Copy Arch Linux to the root mountpoint:
 
    .. code-block:: bash
 
       wget -qO- http://de5.mirror.archlinuxarm.org/os/ArchLinuxARM-armv7-latest.tar.gz | sudo tar -xvzC /path/to/mountpoint/root
       sync
 
-#. Copy additional files and binaries to the root directory in the Arch Linux filesystem
+#. Copy additional files and binaries to the root directory in the Arch Linux filesystem:
 
    .. code-block:: bash
 
@@ -187,7 +187,7 @@ Prepare SD card
 
 .. note::
 
-   ``/path/to/mountpoint/root`` contains the Arch Linux FileSystem, while ``/path/to/mountpoint/root/root/`` is a directory within the FileSystem itself.
+   ``/path/to/mountpoint/root`` contains the Arch Linux filesystem, while ``/path/to/mountpoint/root/root/`` is a directory within the filesystem itself.
 
 .. warning::