diff --git a/litex_boards/platforms/digilent_atlys.py b/litex_boards/platforms/digilent_atlys.py
index 37b1d8d..af73fc1 100644
--- a/litex_boards/platforms/digilent_atlys.py
+++ b/litex_boards/platforms/digilent_atlys.py
@@ -1,705 +1,235 @@
-# Support for the Digilent Atlys (http://digilentinc.com/atlys/) - The board used for HDMI2USB prototyping.
+#
+# This file is part of LiteX-Boards.
+#
+# Copyright (c) 2015-2021 HDMI2USB/LiteX developers
+# SPDX-License-Identifier: BSD-2-Clause
from litex.build.generic_platform import *
-from litex.build.xilinx import XilinxPlatform, iMPACT
-
-# There appear to be 4 x LTC2481C on the U1-SCL / U1-SDA lines connected to the Cypress
-
-class DynamicLVCMOS(object):
- """Object to allow configuration of IOBs connected to dynamic voltage level.
-
- This is used because VCCB2 supply for Bank 2 can be connected to either the
- VCC2V5 or VCC3V3 rail depending on JP12, however there is no way to
- autodetect this.
- """
-
- def __init__(self, name):
- self.name = name
- self.level = None
-
- def set(self, value):
- self.level = {
- "VCC2V5": "LVCMOS25",
- "VCC3V3": "LVCMOS33",
- }[value]
-
- def __str__(self):
- assert self.level, "%s object accessed before voltage level set!" % self.name
- return self.level
-
- def __add__(self, o):
- return str(self) + o
-
- def __radd__(self, o):
- return o + str(self)
-
-
-# VCC Bank 0 == 3V3
-LVCMOS_BANK0 = "LVCMOS33"
-# VCC Bank 1 == 3V3
-LVCMOS_BANK1 = "LVCMOS33"
-# VCC Bank 2 == 3V3 or 2V5
-LVCMOS_BANK2 = DynamicLVCMOS("LVCMOS_BANK2")
-# VCC Bank 3 == 1V8
-LVCMOS_BANK3 = "LVCMOS18"
-# VCC Aux == 3V3
+from litex.build.xilinx import XilinxPlatform
+# IOs ----------------------------------------------------------------------------------------------
_io = [
- # NET "clk" LOC = "L15"; # Bank = 1, Pin name = IO_L42P_GCLK7_M1UDM, Type = GCLK, Sch name = GCLK
- # SG8002JF - 100MHz - CMOS Crystal Oscillator
- ("clk100", 0, Pins("L15"), IOStandard(LVCMOS_BANK1)),
+ # Clk/Rst
+ ("clk100", 0, Pins("L15"), IOStandard("LVCMOS33")),
+ ("cpu_reset", 0, Pins("T15"), IOStandard("LVCMOS33")),
- # M0/RESET button
- # VCCB2 --[10K]--+--[1k]-- M0/Reset
- # |
- # GND -[ BTN ]-+--[390]- BTNRST
- # NET "btn<0>" LOC = "T15"; # Bank = 2, Pin name = IO_L1N_M0_CMPMISO_2, Sch name = M0/RESET
- ("cpu_reset", 0, Pins("T15"), IOStandard(LVCMOS_BANK2)),
+ # Serial
+ ("serial", 0,
+ Subsignal("rx", Pins("A16"), IOStandard("LVCMOS33")),
+ Subsignal("tx", Pins("B16"), IOStandard("LVCMOS33")),
+ ),
- ## onBoard USB controller - FIXME
- # CY7C68013A-56
- # EEPROM config 24AA128 -- A0,A1,A2 = 1,0,0 -- JP9 connects / disconnects SDA
- # NET "EppAstb" LOC = "B9"; # Bank = 0, Pin name = IO_L35P_GCLK17, Sch name = U1-FLAGA
- # NET "EppDstb" LOC = "A9"; # Bank = 0, Pin name = IO_L35N_GCLK16, Sch name = U1-FLAGB
- # NET "UsbFlag" LOC = "C15"; # Bank = 0, Pin name = IO_L64P_SCP5, Sch name = U1-FLAGC
- # NET "EppWait" LOC = "F13"; # Bank = 0, Pin name = IO_L63P_SCP7, Sch name = U1-SLRD
- # NET "EppDB<0>" LOC = "A2"; # Bank = 0, Pin name = IO_L2N, Sch name = U1-FD0
- # NET "EppDB<1>" LOC = "D6"; # Bank = 0, Pin name = IO_L3P, Sch name = U1-FD1
- # NET "EppDB<2>" LOC = "C6"; # Bank = 0, Pin name = IO_L3N, Sch name = U1-FD2
- # NET "EppDB<3>" LOC = "B3"; # Bank = 0, Pin name = IO_L4P, Sch name = U1-FD3
- # NET "EppDB<4>" LOC = "A3"; # Bank = 0, Pin name = IO_L4N, Sch name = U1-FD4
- # NET "EppDB<5>" LOC = "B4"; # Bank = 0, Pin name = IO_L5P, Sch name = U1-FD5
- # NET "EppDB<6>" LOC = "A4"; # Bank = 0, Pin name = IO_L5N, Sch name = U1-FD6
- # NET "EppDB<7>" LOC = "C5"; # Bank = 0, Pin name = IO_L6P, Sch name = U1-FD7
-
- # HDMI2USB configuration....
+ # FX2
("fx2", 0,
- Subsignal("ifclk", Pins("C10")),
- Subsignal("data", Pins("A2 D6 C6 B3 A3 B4 A4 C5")),
- Subsignal("addr", Pins("A14 B14"), Misc("DRIVE=12")),
- Subsignal("flaga", Pins("B9"), Misc("DRIVE=12")),
- Subsignal("flagb", Pins("A9"), Misc("DRIVE=12")),
- Subsignal("flagc", Pins("C15"), Misc("DRIVE=12")),
- Subsignal("rd_n", Pins("F13"), Misc("DRIVE=12")),
- Subsignal("wr_n", Pins("E13")),
- Subsignal("oe_n", Pins("A15"), Misc("DRIVE=12")),
- Subsignal("cs_n", Pins("B2")),
+ Subsignal("ifclk", Pins("C10")),
+ Subsignal("data", Pins("A2 D6 C6 B3 A3 B4 A4 C5")),
+ Subsignal("addr", Pins("A14 B14"), Misc("DRIVE=12")),
+ Subsignal("flaga", Pins("B9"), Misc("DRIVE=12")),
+ Subsignal("flagb", Pins("A9"), Misc("DRIVE=12")),
+ Subsignal("flagc", Pins("C15"), Misc("DRIVE=12")),
+ Subsignal("rd_n", Pins("F13"), Misc("DRIVE=12")),
+ Subsignal("wr_n", Pins("E13")),
+ Subsignal("oe_n", Pins("A15"), Misc("DRIVE=12")),
+ Subsignal("cs_n", Pins("B2")),
Subsignal("pktend_n", Pins("C4"), Misc("DRIVE=12")),
- IOStandard(LVCMOS_BANK0)
+ IOStandard("LVCMOS33")
),
- ## onBoard Quad-SPI Flash
- # 16Mbyte x4 SPI Flash for configuration & data storage. An FPGA
- # configuration file requires less than 12Mbits, leaving 116Mbits
- # available for user data.
- # Numonyx -- N25Q12-F8 or N25Q12-SF
- # DQ0 - SDI, DQ1 - SDO, DQ2 -> ^WP/DQ2 (pulled high), DQ3 -> ^HOLD/DQ3 (pulled high)
+ # SPI Flash
("spiflash4x", 0,
- # NET "FlashCS" LOC = "V3"; # Bank = 2, Pin name = IO_L65N_CSO_B_2, Sch name = CS
Subsignal("cs_n", Pins("V3")),
- # NET "FlashCLK" LOC = "R15"; # Bank = 2, Pin name = IO_L1P_CCLK_2, Sch name = SCK
- Subsignal("clk", Pins("R15")),
- # NET "FlashMemDq<0>" LOC = "T13"; # Bank = 2, Pin name = IO_L3N_MOSI_CSI_B_MISO0_2, Sch name = SDI
- # NET "FlashMemDq<1>" LOC = "R13"; # Bank = 2, Pin name = IO_L3P_D0_DIN_MISO_MISO1_2, Sch name = DQ1
- # NET "FlashMemDq<2>" LOC = "T14"; # Bank = 2, Pin name = IO_L12P_D1_MISO2_2, Sch name = DQ2
- # NET "FlashMemDq<3>" LOC = "V14"; # Bank = 2, Pin name = IO_L12N_D2_MISO3_2, Sch name = DQ3
- Subsignal("dq", Pins("T13", "R13", "T14", "V14")),
- IOStandard(LVCMOS_BANK2), Misc("SLEW=FAST")
+ Subsignal("clk", Pins("R15")),
+ Subsignal("dq", Pins("T13", "R13", "T14", "V14")),
+ IOStandard("LVCMOS33"),
+ Misc("SLEW=FAST"),
),
- ## onBoard Leds
- # NET "Led<0>" LOC = "U18"; # Bank = 1, Pin name = IO_L52N_M1DQ15, Sch name = LD0
- # NET "Led<1>" LOC = "M14"; # Bank = 1, Pin name = IO_L53P, Sch name = LD1
- # NET "Led<2>" LOC = "N14"; # Bank = 1, Pin name = IO_L53N_VREF, Sch name = LD2
- # NET "Led<3>" LOC = "L14"; # Bank = 1, Pin name = IO_L61P, Sch name = LD3
- # NET "Led<4>" LOC = "M13"; # Bank = 1, Pin name = IO_L61N, Sch name = LD4
- # NET "Led<5>" LOC = "D4"; # Bank = 0, Pin name = IO_L1P_HSWAPEN_0, Sch name = HSWAP/LD5
- # NET "Led<6>" LOC = "P16"; # Bank = 1, Pin name = IO_L74N_DOUT_BUSY_1, Sch name = LD6
- # NET "Led<7>" LOC = "N12"; # Bank = 2, Pin name = IO_L13P_M1_2, Sch name = M1/LD7
- ("user_led", 0, Pins("U18"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 1, Pins("M14"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 2, Pins("N14"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 3, Pins("L14"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 4, Pins("M13"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 5, Pins("D4"), IOStandard(LVCMOS_BANK0)),
- ("user_led", 6, Pins("P16"), IOStandard(LVCMOS_BANK1)),
- ("user_led", 7, Pins("N12"), IOStandard(LVCMOS_BANK2)),
+ # Leds
+ ("user_led", 0, Pins("U18"), IOStandard("LVCMOS33")),
+ ("user_led", 1, Pins("M14"), IOStandard("LVCMOS33")),
+ ("user_led", 2, Pins("N14"), IOStandard("LVCMOS33")),
+ ("user_led", 3, Pins("L14"), IOStandard("LVCMOS33")),
+ ("user_led", 4, Pins("M13"), IOStandard("LVCMOS33")),
+ ("user_led", 5, Pins("D4"), IOStandard("LVCMOS33")),
+ ("user_led", 6, Pins("P16"), IOStandard("LVCMOS33")),
+ ("user_led", 7, Pins("N12"), IOStandard("LVCMOS33")),
- ## onBoard PUSH BUTTONS - FIXME
- # Mapping "up" to north
- # VCC1V8 - pulled down to GND via 10k
- # NET "btn<1>" LOC = "N4"; # Bank = 3, Pin name = IO_L1P, Sch name = BTNU
- ("user_btn", 0, Pins("N4"), IOStandard(LVCMOS_BANK3)), # North button
- # NET "btn<2>" LOC = "P4"; # Bank = 3, Pin name = IO_L2P, Sch name = BTNL
- ("user_btn", 1, Pins("P4"), IOStandard(LVCMOS_BANK3)), # East button
- # NET "btn<3>" LOC = "P3"; # Bank = 3, Pin name = IO_L2N, Sch name = BTND
- ("user_btn", 2, Pins("P3"), IOStandard(LVCMOS_BANK3)), # South button
- # NET "btn<4>" LOC = "F6"; # Bank = 3, Pin name = IO_L55P_M3A13, Sch name = BTNR
- ("user_btn", 3, Pins("F6"), IOStandard(LVCMOS_BANK3)), # West button
- # NET "btn<5>" LOC = "F5"; # Bank = 3, Pin name = IO_L55N_M3A14, Sch name = BTNC
- ("user_btn", 4, Pins("F5"), IOStandard(LVCMOS_BANK3)), # Center button
+ # Buttons
+ ("user_btn", 0, Pins("N4"), IOStandard("LVCMOS18")), # North button
+ ("user_btn", 1, Pins("P4"), IOStandard("LVCMOS18")), # East button
+ ("user_btn", 2, Pins("P3"), IOStandard("LVCMOS18")), # South button
+ ("user_btn", 3, Pins("F6"), IOStandard("LVCMOS18")), # West button
+ ("user_btn", 4, Pins("F5"), IOStandard("LVCMOS18")), # Center button
- ## onBoard SWITCHES - FIXME
- # SW(0,1,2,3) - VCC3V3 / GND
- # SW(4,5,6) - VCCB2 / GND
- # SW(7) - VCC1V8 / GND
- # NET "sw<0>" LOC = "A10"; # Bank = 0, Pin name = IO_L37N_GCLK12, Sch name = SW0
- # NET "sw<1>" LOC = "D14"; # Bank = 0, Pin name = IO_L65P_SCP3, Sch name = SW1
- # NET "sw<2>" LOC = "C14"; # Bank = 0, Pin name = IO_L65N_SCP2, Sch name = SW2
- # NET "sw<3>" LOC = "P15"; # Bank = 1, Pin name = IO_L74P_AWAKE_1, Sch name = SW3
- # NET "sw<4>" LOC = "P12"; # Bank = 2, Pin name = IO_L13N_D10, Sch name = SW4
- # NET "sw<5>" LOC = "R5"; # Bank = 2, Pin name = IO_L48P_D7, Sch name = SW5
- # NET "sw<6>" LOC = "T5"; # Bank = 2, Pin name = IO_L48N_RDWR_B_VREF_2, Sch name = SW6
- # NET "sw<7>" LOC = "E4"; # Bank = 3, Pin name = IO_L54P_M3RESET, Sch name = SW7
- ("user_sw", 0, Pins("A10"), IOStandard(LVCMOS_BANK0)),
- ("user_sw", 1, Pins("D14"), IOStandard(LVCMOS_BANK0)),
- ("user_sw", 2, Pins("C14"), IOStandard(LVCMOS_BANK0)),
- ("user_sw", 3, Pins("P15"), IOStandard(LVCMOS_BANK1)),
- ("user_sw", 4, Pins("P12"), IOStandard(LVCMOS_BANK2)),
- ("user_sw", 5, Pins("R5"), IOStandard(LVCMOS_BANK2)),
- ("user_sw", 6, Pins("T5"), IOStandard(LVCMOS_BANK2)),
- ("user_sw", 7, Pins("E4"), IOStandard(LVCMOS_BANK3)),
+ # Switches.
+ ("user_sw", 0, Pins("A10"), IOStandard("LVCMOS33")),
+ ("user_sw", 1, Pins("D14"), IOStandard("LVCMOS33")),
+ ("user_sw", 2, Pins("C14"), IOStandard("LVCMOS33")),
+ ("user_sw", 3, Pins("P15"), IOStandard("LVCMOS33")),
+ ("user_sw", 4, Pins("P12"), IOStandard("LVCMOS33")),
+ ("user_sw", 5, Pins("R5"), IOStandard("LVCMOS33")),
+ ("user_sw", 6, Pins("T5"), IOStandard("LVCMOS33")),
+ ("user_sw", 7, Pins("E4"), IOStandard("LVCMOS18")),
- ## TEMAC Ethernet MAC - FIXME
- # 10/100/1000 Ethernet PHY
- # 88E111-B2-RCJ1-C000 - Marvell Alaska Tri-mode PHY (the 88E1111)
- # paired with a Halo HFJ11-1G01E RJ-45 connector
- # Runs from 1.2V power supply
+ # GMII/MII Ethernet
("eth_clocks", 0,
- # NET "phytxclk" LOC = "K16"; # Bank = 1, Pin name = IO_L41N_GCLK8_M1CASN, Sch name = E-TXCLK
- Subsignal("tx", Pins("K16")),
- # NET "phygtxclk" LOC = "L12"; # Bank = 1, Pin name = IO_L40P_GCLK11_M1A5, Sch name = E-GTXCLK
+ Subsignal("tx", Pins("K16")),
Subsignal("gtx", Pins("L12")),
- # NET "phyrxclk" LOC = "K15"; # Bank = 1, Pin name = IO_L41P_GCLK9_IRDY1_M1RASN, Sch name = E-RXCLK
- Subsignal("rx", Pins("K15")),
- IOStandard(LVCMOS_BANK1)
+ Subsignal("rx", Pins("K15")),
+ IOStandard("LVCMOS33")
),
-
("eth", 0,
- # NET "phyrst" LOC = "G13"; # Bank = 1, Pin name = IO_L32N_A16_M1A9, Sch name = E-RESET
- Subsignal("rst_n", Pins("G13")),
- # NET "phyint" LOC = "L16"; # Bank = 1, Pin name = IO_L42N_GCLK6_TRDY1_M1LDM, Sch name = E-INT
- Subsignal("int_n", Pins("L16")),
- # NET "phymdi" LOC = "N17"; # Bank = 1, Pin name = IO_L48P_HDC_M1DQ8, Sch name = E-MDIO
- Subsignal("mdio", Pins("N17")),
- # NET "phymdc" LOC = "F16"; # Bank = 1, Pin name = IO_L1N_A24_VREF, Sch name = E-MDC
- Subsignal("mdc", Pins("F16")),
- # NET "phyrxdv" LOC = "F17"; # Bank = 1, Pin name = IO_L35P_A11_M1A7, Sch name = E-RXDV
- Subsignal("rx_dv", Pins("F17")),
- # NET "phyrxer" LOC = "F18"; # Bank = 1, Pin name = IO_L35N_A10_M1A2, Sch name = E-RXER
- Subsignal("rx_er", Pins("F18")),
- # NET "phyRXD<0>" LOC = "G16"; # Bank = 1, Pin name = IO_L38P_A5_M1CLK, Sch name = E-RXD0
- # NET "phyRXD<1>" LOC = "H14"; # Bank = 1, Pin name = IO_L36N_A8_M1BA1, Sch name = E-RXD1
- # NET "phyRXD<2>" LOC = "E16"; # Bank = 1, Pin name = IO_L33P_A15_M1A10, Sch name = E-RXD2
- # NET "phyRXD<3>" LOC = "F15"; # Bank = 1, Pin name = IO_L1P_A25, Sch name = E-RXD3
- # NET "phyRXD<4>" LOC = "F14"; # Bank = 1, Pin name = IO_L30P_A21_M1RESET, Sch name = E-RXD4
- # NET "phyRXD<5>" LOC = "E18"; # Bank = 1, Pin name = IO_L33N_A14_M1A4, Sch name = E-RXD5
- # NET "phyRXD<6>" LOC = "D18"; # Bank = 1, Pin name = IO_L31N_A18_M1A12, Sch name = E-RXD6
- # NET "phyRXD<7>" LOC = "D17"; # Bank = 1, Pin name = IO_L31P_A19_M1CKE, Sch name = E-RXD7
+ Subsignal("rst_n", Pins("G13")),
+ Subsignal("int_n", Pins("L16")),
+ Subsignal("mdio", Pins("N17")),
+ Subsignal("mdc", Pins("F16")),
+ Subsignal("rx_dv", Pins("F17")),
+ Subsignal("rx_er", Pins("F18")),
Subsignal("rx_data", Pins("G16 H14 E16 F15 F14 E18 D18 D17")),
- # NET "phytxen" LOC = "H15"; # Bank = 1, Pin name = IO_L37P_A7_M1A0, Sch name = E-TXEN
- Subsignal("tx_en", Pins("H15")),
- # NET "phytxer" LOC = "G18"; # Bank = 1, Pin name = IO_L38N_A4_M1CLKN, Sch name = E-TXER
- Subsignal("tx_er", Pins("G18")),
- # NET "phyTXD<0>" LOC = "H16"; # Bank = 1, Pin name = IO_L37N_A6_M1A1, Sch name = E-TXD0
- # NET "phyTXD<1>" LOC = "H13"; # Bank = 1, Pin name = IO_L36P_A9_M1BA0, Sch name = E-TXD1
- # NET "phyTXD<2>" LOC = "K14"; # Bank = 1, Pin name = IO_L39N_M1ODT, Sch name = E-TXD2
- # NET "phyTXD<3>" LOC = "K13"; # Bank = 1, Pin name = IO_L34N_A12_M1BA2, Sch name = E-TXD3
- # NET "phyTXD<4>" LOC = "J13"; # Bank = 1, Pin name = IO_L39P_M1A3, Sch name = E-TXD4
- # NET "phyTXD<5>" LOC = "G14"; # Bank = 1, Pin name = IO_L30N_A20_M1A11, Sch name = E-TXD5
- # NET "phyTXD<6>" LOC = "H12"; # Bank = 1, Pin name = IO_L32P_A17_M1A8, Sch name = E-TXD6
- # NET "phyTXD<7>" LOC = "K12"; # Bank = 1, Pin name = IO_L34P_A13_M1WE, Sch name = E-TXD7
+ Subsignal("tx_en", Pins("H15")),
+ Subsignal("tx_er", Pins("G18")),
Subsignal("tx_data", Pins("H16 H13 K14 K13 J13 G14 H12 K12")),
- # C17 - from Atlys reference manual, not listed in UCF file?
- Subsignal("col", Pins("C17")),
- # C18 - from Atlys reference manual, not listed in UCF file?
- Subsignal("crs", Pins("C18")),
- IOStandard(LVCMOS_BANK1)
+ Subsignal("col", Pins("C17")),
+ Subsignal("crs", Pins("C18")),
+ IOStandard("LVCMOS33")
),
- ## DDR2
- # 128Mbyte DDR2 16-bit wide data @ 800MHz
- # Older boards - MT47H64M16HR-25E - DDR2 - 2.5ns @ CL = 5 (DDR2-800)
- # Newer boards - MIRA P3R1GE3EGF G8E DDR2 -
- #
- # The interface supports SSTL18 signaling. Address and control signals
- # are terminated through 47-ohm resistors to a 0.9V VTT, and data
- # signals use the On-Die-Termination (ODT) feature of the DDR2 chip.
- #
- # When generating a MIG core for the MIRA part, selecting the
- # “EDE1116AXXX-8E” device will result in the correct timing parameters
- # being set. When generating a component for the Micron part, it can be
- # selected by name within the wizard. The part loaded on your Atlys can
- # be determined by examining the print on the DDR2 component (IC13).
- #
- # NET "DDR2CLK0" LOC = "G3"; # Bank = 3, Pin name = IO_L46P_M3CLK, Sch name = DDR-CK_P
- # NET "DDR2CLK1" LOC = "G1"; # Bank = 3, Pin name = IO_L46N_M3CLKN, Sch name = DDR-CK_N
+ # DDR2 SDRAM.
("ddram_clock", 0,
Subsignal("p", Pins("G3")),
Subsignal("n", Pins("G1")),
IOStandard("DIFF_SSTL18_II"), Misc("IN_TERM=NONE")
),
("ddram", 0,
- # NET "DDR2CKE" LOC = "H7"; # Bank = 3, Pin name = IO_L53P_M3CKE, Sch name = DDR-CKE
- Subsignal("cke", Pins("H7"), IOStandard("SSTL18_II")),
- # NET "DDR2RASN" LOC = "L5"; # Bank = 3, Pin name = IO_L43P_GCLK23_M3RASN, Sch name = DDR-RAS
+ Subsignal("cke", Pins("H7"), IOStandard("SSTL18_II")),
Subsignal("ras_n", Pins("L5"), IOStandard("SSTL18_II")),
- # NET "DDR2CASN" LOC = "K5"; # Bank = 3, Pin name = IO_L43N_GCLK22_IRDY2_M3CASN, Sch name = DDR-CAS
Subsignal("cas_n", Pins("K5"), IOStandard("SSTL18_II")),
- # NET "DDR2WEN" LOC = "E3"; # Bank = 3, Pin name = IO_L50P_M3WE, Sch name = DDR-WE
- Subsignal("we_n", Pins("E3"), IOStandard("SSTL18_II")),
-
- # NET "DDR2BA0" LOC = "F2"; # Bank = 3, Pin name = IO_L48P_M3BA0, Sch name = DDR-BA0
- # NET "DDR2BA1" LOC = "F1"; # Bank = 3, Pin name = IO_L48N_M3BA1, Sch name = DDR-BA1
- # NET "DDR2BA2" LOC = "E1"; # Bank = 3, Pin name = IO_L50N_M3BA2, Sch name = DDR-BA2
- Subsignal("ba", Pins("F2 F1 E1"), IOStandard("SSTL18_II")),
-
- # NET "DDR2A0" LOC = "J7"; # Bank = 3, Pin name = IO_L47P_M3A0, Sch name = DDR-A0
- # NET "DDR2A1" LOC = "J6"; # Bank = 3, Pin name = IO_L47N_M3A1, Sch name = DDR-A1
- # NET "DDR2A2" LOC = "H5"; # Bank = 3, Pin name = IO_L49N_M3A2, Sch name = DDR-A2
- # NET "DDR2A3" LOC = "L7"; # Bank = 3, Pin name = IO_L45P_M3A3, Sch name = DDR-A3
- # NET "DDR2A4" LOC = "F3"; # Bank = 3, Pin name = IO_L51N_M3A4, Sch name = DDR-A4
- # NET "DDR2A5" LOC = "H4"; # Bank = 3, Pin name = IO_L44P_GCLK21_M3A5, Sch name = DDR-A5
- # NET "DDR2A6" LOC = "H3"; # Bank = 3, Pin name = IO_L44N_GCLK20_M3A6, Sch name = DDR-A6
- # NET "DDR2A7" LOC = "H6"; # Bank = 3, Pin name = IO_L49P_M3A7, Sch name = DDR-A7
- # NET "DDR2A8" LOC = "D2"; # Bank = 3, Pin name = IO_L52P_M3A8, Sch name = DDR-A8
- # NET "DDR2A9" LOC = "D1"; # Bank = 3, Pin name = IO_L52N_M3A9, Sch name = DDR-A9
- # NET "DDR2A10" LOC = "F4"; # Bank = 3, Pin name = IO_L51P_M3A10, Sch name = DDR-A10
- # NET "DDR2A11" LOC = "D3"; # Bank = 3, Pin name = IO_L54N_M3A11, Sch name = DDR-A11
- # NET "DDR2A12" LOC = "G6"; # Bank = 3, Pin name = IO_L53N_M3A12, Sch name = DDR-A12
- Subsignal("a", Pins("J7 J6 H5 L7 F3 H4 H3 H6 D2 D1 F4 D3 G6"), IOStandard("SSTL18_II")),
- # NET "DDR2DQ0" LOC = "L2"; # Bank = 3, Pin name = IO_L37P_M3DQ0, Sch name = DDR-DQ0
- # NET "DDR2DQ1" LOC = "L1"; # Bank = 3, Pin name = IO_L37N_M3DQ1, Sch name = DDR-DQ1
- # NET "DDR2DQ2" LOC = "K2"; # Bank = 3, Pin name = IO_L38P_M3DQ2, Sch name = DDR-DQ2
- # NET "DDR2DQ3" LOC = "K1"; # Bank = 3, Pin name = IO_L38N_M3DQ3, Sch name = DDR-DQ3
- # NET "DDR2DQ4" LOC = "H2"; # Bank = 3, Pin name = IO_L41P_GCLK27_M3DQ4, Sch name = DDR-DQ4
- # NET "DDR2DQ5" LOC = "H1"; # Bank = 3, Pin name = IO_L41N_GCLK26_M3DQ5, Sch name = DDR-DQ5
- # NET "DDR2DQ6" LOC = "J3"; # Bank = 3, Pin name = IO_L40P_M3DQ6, Sch name = DDR-DQ6
- # NET "DDR2DQ7" LOC = "J1"; # Bank = 3, Pin name = IO_L40N_M3DQ7, Sch name = DDR-DQ7
- # NET "DDR2DQ8" LOC = "M3"; # Bank = 3, Pin name = IO_L36P_M3DQ8, Sch name = DDR-DQ8
- # NET "DDR2DQ9" LOC = "M1"; # Bank = 3, Pin name = IO_L36N_M3DQ9, Sch name = DDR-DQ9
- # NET "DDR2DQ10" LOC = "N2"; # Bank = 3, Pin name = IO_L35P_M3DQ10, Sch name = DDR-DQ10
- # NET "DDR2DQ11" LOC = "N1"; # Bank = 3, Pin name = IO_L35N_M3DQ11, Sch name = DDR-DQ11
- # NET "DDR2DQ12" LOC = "T2"; # Bank = 3, Pin name = IO_L33P_M3DQ12, Sch name = DDR-DQ12
- # NET "DDR2DQ13" LOC = "T1"; # Bank = 3, Pin name = IO_L33N_M3DQ13, Sch name = DDR-DQ13
- # NET "DDR2DQ14" LOC = "U2"; # Bank = 3, Pin name = IO_L32P_M3DQ14, Sch name = DDR-DQ14
- # NET "DDR2DQ15" LOC = "U1"; # Bank = 3, Pin name = IO_L32N_M3DQ15, Sch name = DDR-DQ15
+ Subsignal("we_n", Pins("E3"), IOStandard("SSTL18_II")),
+ Subsignal("ba", Pins("F2 F1 E1"), IOStandard("SSTL18_II")),
+ Subsignal("a", Pins(
+ "J7 J6 H5 L7 F3 H4 H3 H6",
+ "D2 D1 F4 D3 G6"),
+ IOStandard("SSTL18_II")),
Subsignal("dq", Pins(
- "L2 L1 K2 K1 H2 H1 J3 J1",
- "M3 M1 N2 N1 T2 T1 U2 U1"), IOStandard("SSTL18_II")),
- # U == Upper, L == Lower
- # NET "DDR2UDQS" LOC="P2"; # Bank = 3, Pin name = IO_L34P_M3UDQS, Sch name = DDR-UDQS_P
- # NET "DDR2UDQSN" LOC="P1"; # Bank = 3, Pin name = IO_L34N_M3UDQSN, Sch name = DDR-UDQS_N
- # NET "DDR2LDQS" LOC="L4"; # Bank = 3, Pin name = IO_L39P_M3LDQS, Sch name = DDR-LDQS_P
- # NET "DDR2LDQSN" LOC="L3"; # Bank = 3, Pin name = IO_L39N_M3LDQSN, Sch name = DDR-LDQS_N
- Subsignal("dqs", Pins("P2 L4"), IOStandard("DIFF_SSTL18_II")),
+ "L2 L1 K2 K1 H2 H1 J3 J1",
+ "M3 M1 N2 N1 T2 T1 U2 U1"),
+ IOStandard("SSTL18_II")),
+ Subsignal("dqs", Pins("P2 L4"), IOStandard("DIFF_SSTL18_II")),
Subsignal("dqs_n", Pins("P1 L3"), IOStandard("DIFF_SSTL18_II")),
- # NET "DDR2UDM" LOC="K4"; # Bank = 3, Pin name = IO_L42P_GCLK25_TRDY2_M3UDM, Sch name = DDR-UDM
- # NET "DDR2LDM" LOC="K3"; # Bank = 3, Pin name = IO_L42N_GCLK24_M3LDM, Sch name = DDR-LDM
- Subsignal("dm", Pins("K4 K3"), IOStandard("SSTL18_II")),
- # NET "DDR2ODT" LOC="K6"; # Bank = 3, Pin name = IO_L45N_M3ODT, Sch name = DDR-ODT
- Subsignal("odt", Pins("K6"), IOStandard("SSTL18_II"))
+ Subsignal("dm", Pins("K4 K3"), IOStandard("SSTL18_II")),
+ Subsignal("odt", Pins("K6"), IOStandard("SSTL18_II"))
),
- ## onboard HDMI OUT
- # Type A connector, marked as J2 on the board, next to the power connector.
- # Buffered / protected with TMDS141RHAR
- # NET "HDMIOUTCLKP" LOC = "B6"; # Bank = 0, Pin name = IO_L8P, Sch name = TMDS-TX-CLK_P
- # NET "HDMIOUTCLKN" LOC = "A6"; # Bank = 0, Pin name = IO_L8N_VREF, Sch name = TMDS-TX-CLK_N
- # NET "HDMIOUTD0P" LOC = "D8"; # Bank = 0, Pin name = IO_L11P, Sch name = TMDS-TX-0_P
- # NET "HDMIOUTD0N" LOC = "C8"; # Bank = 0, Pin name = IO_L11N, Sch name = TMDS-TX-0_N
- # NET "HDMIOUTD1P" LOC = "C7"; # Bank = 0, Pin name = IO_L10P, Sch name = TMDS-TX-1_P
- # NET "HDMIOUTD1N" LOC = "A7"; # Bank = 0, Pin name = IO_L10N, Sch name = TMDS-TX-1_N
- # NET "HDMIOUTD2P" LOC = "B8"; # Bank = 0, Pin name = IO_L33P, Sch name = TMDS-TX-2_P
- # NET "HDMIOUTD2N" LOC = "A8"; # Bank = 0, Pin name = IO_L33N, Sch name = TMDS-TX-2_N
- # NET "HDMIOUTSCL" LOC = "D9"; # Bank = 0, Pin name = IO_L34P_GCLK19, Sch name = TMDS-TX-SCL
- # NET "HDMIOUTSDA" LOC = "C9"; # Bank = 0, Pin name = IO_L34N_GCLK18, Sch name = TMDS-TX-SDA
+ # HDMI Out 0
("hdmi_out", 0,
- Subsignal("clk_p", Pins("B6"), IOStandard("TMDS_33")),
- Subsignal("clk_n", Pins("A6"), IOStandard("TMDS_33")),
+ Subsignal("clk_p", Pins("B6"), IOStandard("TMDS_33")),
+ Subsignal("clk_n", Pins("A6"), IOStandard("TMDS_33")),
Subsignal("data0_p", Pins("D8"), IOStandard("TMDS_33")),
Subsignal("data0_n", Pins("C8"), IOStandard("TMDS_33")),
Subsignal("data1_p", Pins("C7"), IOStandard("TMDS_33")),
Subsignal("data1_n", Pins("A7"), IOStandard("TMDS_33")),
Subsignal("data2_p", Pins("B8"), IOStandard("TMDS_33")),
Subsignal("data2_n", Pins("A8"), IOStandard("TMDS_33")),
- # Disconnect JP6 and JP7 for FPGA SCL/SDA control, otherwise
- # this is connected to J3's SCL/SDA pins.
- Subsignal("scl", Pins("D9"), IOStandard("I2C")),
- Subsignal("sda", Pins("C9"), IOStandard("I2C")),
+ Subsignal("scl", Pins("D9"), IOStandard("I2C")),
+ Subsignal("sda", Pins("C9"), IOStandard("I2C")),
),
- ## onboard HDMI IN1 (PMODA)
- # Type A connector, marked as J1, on side with USB connectors.
- # Buffered / protected with TMDS141RHAR
- # JP4 connects / disconnects 5V to HDMI pin 18, for input to work make
- # sure it is connected.
- # NET "HDMIIN1CLKP" LOC = "D11"; # Bank = 0, Pin name = IO_L36P_GCLK15, Sch name = TMDS-RXB-CLK_P
- # NET "HDMIIN1CLKN" LOC = "C11"; # Bank = 0, Pin name = IO_L36N_GCLK14, Sch name = TMDS-RXB-CLK_N
- # NET "HDMIIN1D0P" LOC = "G9"; # Bank = 0, Pin name = IO_L38P, Sch name = TMDS-RXB-0_P
- # NET "HDMIIN1D0N" LOC = "F9"; # Bank = 0, Pin name = IO_L38N_VREF, Sch name = TMDS-RXB-0_N
- # NET "HDMIIN1D1P" LOC = "B11"; # Bank = 0, Pin name = IO_L39P, Sch name = TMDS-RXB-1_P
- # NET "HDMIIN1D1N" LOC = "A11"; # Bank = 0, Pin name = O_L39N, Sch name = TMDS-RXB-1_N
- # NET "HDMIIN1D2P" LOC = "B12"; # Bank = 0, Pin name = IO_L41P, Sch name = TMDS-RXB-2_P
- # NET "HDMIIN1D2N" LOC = "A12"; # Bank = 0, Pin name = IO_L41N, Sch name = TMDS-RXB-2_N
- # NET "HDMIIN1SCL" LOC = "C13"; # Bank = 0, Pin name = IO_L50P, Sch name = PMOD-SCL
- # NET "HDMIIN1SDA" LOC = "A13"; # Bank = 0, Pin name = IO_L50N, Sch name = PMOD-SDA
+ # HDMI In 0
("hdmi_in", 0,
- Subsignal("clk_p", Pins("D11")),
- Subsignal("clk_n", Pins("C11")),
+ Subsignal("clk_p", Pins("D11")),
+ Subsignal("clk_n", Pins("C11")),
Subsignal("data0_p", Pins("G9")),
Subsignal("data0_n", Pins("F9")),
Subsignal("data1_p", Pins("B11")),
Subsignal("data1_n", Pins("A11")),
Subsignal("data2_p", Pins("B12")),
Subsignal("data2_n", Pins("A12")),
- # Make sure JP2 is connected. Shared with J1.
- Subsignal("scl", Pins("C13"), IOStandard(LVCMOS_BANK0)),
- Subsignal("sda", Pins("A13"), IOStandard(LVCMOS_BANK0)),
- #Subsignal("hpd_notif", Pins("G22"), IOStandard("LVCMOS33")),
- #Subsignal("hpd_en", Pins("G17"), IOStandard("LVCMOS33"))
+ Subsignal("scl", Pins("C13"), IOStandard("LVCMOS33")),
+ Subsignal("sda", Pins("A13"), IOStandard("LVCMOS33")),
),
- ## onboard HDMI IN2
- # Type A connector, marked as J3, between audio connectors and Ethernet
- # RJ45 connector.
- # Buffered / protected with a TMDS141RHAR
- # JP8 connects / disconnects 5V to HDMI pin 18, for input to work make
- # sure it is connected.
- # NET "HDMIIN2CLKP" LOC = "H17"; # Bank = 1, Pin name = IO_L43P_GCLK5_M1DQ4, Sch name = TMDS-RX-CLK_P
- # NET "HDMIIN2CLKN" LOC = "H18"; # Bank = 1, Pin name = IO_L43N_GCLK4_M1DQ5, Sch name = TMDS-RX-CLK_N
- # NET "HDMIIN2D0P" LOC = "K17"; # Bank = 1, Pin name = IO_L45P_A1_M1LDQS, Sch name = TMDS-RX-0_P
- # NET "HDMIIN2D0N" LOC = "K18"; # Bank = 1, Pin name = IO_L45N_A0_M1LDQSN, Sch name = TMDS-RX-0_N
- # NET "HDMIIN2D1P" LOC = "L17"; # Bank = 1, Pin name = IO_L46P_FCS_B_M1DQ2, Sch name = TMDS-RX-1_P
- # NET "HDMIIN2D1N" LOC = "L18"; # Bank = 1, Pin name = IO_L46N_FOE_B_M1DQ3, Sch name = TMDS-RX-1_N
- # NET "HDMIIN2D2P" LOC = "J16"; # Bank = 1, Pin name = IO_L44P_A3_M1DQ6, Sch name = TMDS-RX-2_P
- # NET "HDMIIN2D2N" LOC = "J18"; # Bank = 1, Pin name = IO_L44N_A2_M1DQ7, Sch name = TMDS-RX-2_N
- # NET "HDMIIN2SCL" LOC = "M16"; # Bank = 1, Pin name = IO_L47P_FWE_B_M1DQ0, Sch name = TMDS-RX-SCL
- # NET "HDMIIN2SDA" LOC = "M18"; # Bank = 1, Pin name = IO_L47N_LDC_M1DQ1, Sch name = TMDS-RX-SDA
+ # HDMI In 1
("hdmi_in", 1,
- Subsignal("clk_p", Pins("H17")),
- Subsignal("clk_n", Pins("H18")),
+ Subsignal("clk_p", Pins("H17")),
+ Subsignal("clk_n", Pins("H18")),
Subsignal("data0_p", Pins("K17")),
Subsignal("data0_n", Pins("K18")),
Subsignal("data1_p", Pins("L17")),
Subsignal("data1_n", Pins("L18")),
Subsignal("data2_p", Pins("J16")),
Subsignal("data2_n", Pins("J18")),
- # Disconnect JP6 and JP7 for FPGA SCL/SDA control, otherwise
- # this is connected to J2's SCL/SDA pins.
- Subsignal("scl", Pins("M16"), IOStandard(LVCMOS_BANK1)),
- Subsignal("sda", Pins("M18"), IOStandard(LVCMOS_BANK1)),
- #Subsignal("hpd_notif", Pins("G16"), IOStandard("LVCMOS33")),
- #Subsignal("hpd_en", Pins("B20"), IOStandard("LVCMOS33"))
- ),
-
- ## onboard USB Host Controller - FIXME
- # PIC32MX440F256H-40I/MR
- # USB-HID port (for mouse/keyboard)
- # PS/2 Keyboard - K_CLK - P17
- # PS/2 Keyboard - K_DAT - N15
- # PS/2 Mouse - M_CLK - N18
- # PS/2 Mouse - M_DAT - P18
- # FPGA Serial programming - DIN - R13
- # FPGA Serial programming - CLK - R15
- # NET "USBCLK" LOC = "P17"; # Bank = 1, Pin name = IO_L49P_M1DQ10, Sch name = PIC32-SCK1
- # NET "USBSDI" LOC = "N15"; # Bank = 1, Pin name = IO_L50P_M1UDQS, Sch name = PIC32-SDI1
-
- # NET "USBSS" LOC = "P18"; # Bank = 1, Pin name = IO_L49N_M1DQ11, Sch name = PIC32-SS1
- # NET "USBSDO" LOC = "N18"; # Bank = 1, Pin name = IO_L48N_M1DQ9, Sch name = PIC32-SDO1
-
- ## Audio - FIXME
- # National Semiconductor - LM4550VH
- # AC-97 Codec with line-in, line-out, mic, & headphone
- # Audio
- # NET "BITCLK" LOC = "L13"; # Bank = 1, Pin name = IO_L40N_GCLK10_M1A6, Sch name = AUD-BIT-CLK
- # NET "AUDSYNC" LOC = "U17"; # Bank = 1, Pin name = IO_L52P_M1DQ14, Sch name = AUD-SYNC
- # NET "AUDRST" LOC = "T17"; # Bank = 1, Pin name = IO_L51P_M1DQ12, Sch name = AUD-RESET
- # NET "AUDSDI" LOC = "T18"; # Bank = 1, Pin name = IO_L51N_M1DQ13, Sch name = AUD-SDI
- # NET "AUDSDO" LOC = "N16"; # Bank = 1, Pin name = IO_L50N_M1UDQSN, Sch name = AUD-SDO
-
- ## USB UART Connector
- # USB Micro B port marked as UART between HDMI connector and USB A connector.
- # XR21V1410IL16 - Vizzini USB Serial - https://github.com/shenki/exar-uart-driver
- # NET "UartRx" LOC = "A16"; # Bank = 0, Pin name = IO_L66N_SCP0, Sch name = USBB-RXD
- # NET "UartTx" LOC = "B16"; # Bank = 0, Pin name = IO_L66P_SCP1, Sch name = USBB-TXD
- ("serial", 0,
- Subsignal("rx", Pins("A16"), IOStandard("LVCMOS33")),
- Subsignal("tx", Pins("B16"), IOStandard("LVCMOS33")),
- ),
-
-# ("fpga_cfg",
-# Subsignal("din", Pins("T14")),
-# Subsignal("cclk", Pins("R14")),
-# Subsignal("init_b", Pins("T12")),
-# Subsignal("prog_b", Pins("A2")),
-# Subsignal("done", Pins("T15")),
-# ),
-# ("jtag",
-# Subsignal("tms", Pins("B2")),
-# Subsignal("tdo", Pins("B16")),
-# Subsignal("tdi", Pins("B1")),
-# Subsignal("tck", Pins("A15")),
-# ),
-
-]
-
-# This Micro-D HDMI connector only works when VCCB2 is set to 3V3.
-_io_vccb2_3v3 = [
- ## PMOD Connector
- # Micro-D connector, marked as JB, on the same side as switches + LEDs
- # but on the underside of the board below MOD connector. Works as
- # either output or input because it isn't buffered. Also often referred
- # to as "JA".
- # JP12 connects VCC to 3.3V or 2.5V, make sure 3.3V is selected.
- # JP3 connects / disconnects 5V to HDMI pin 19.
- # * To use as output, remove the jumper.
- # * To use as input, make sure it is connected.
- # NET "JB<5>" LOC = "T9"; # Bank = 2, Pin name = IO_L32P_GCLK29, Sch name = JA-CLK_P
- # NET "JB<4>" LOC = "V9"; # Bank = 2, Pin name = IO_L32N_GCLK28, Sch name = JA-CLK_N
- # NET "JB<1>" LOC = "R3"; # Bank = 2, Pin name = IO_L62P_D5, Sch name = JA-D0_P
- # NET "JB<0>" LOC = "T3"; # Bank = 2, Pin name = IO_L62N_D6, Sch name = JA-D0_N
- # NET "JB<7>" LOC = "T4"; # Bank = 2, Pin name = IO_L63P, Sch name = JA-D1_P
- # NET "JB<6>" LOC = "V4"; # Bank = 2, Pin name = IO_L63N, Sch name = JA-D1_N
- # NET "JB<3>" LOC = "N5"; # Bank = 2, Pin name = IO_L64P_D8, Sch name = JA-D2_P
- # NET "JB<2>" LOC = "P6"; # Bank = 2, Pin name = IO_L64N_D9, Sch name = JA-D2_N
- ("hdmi_out", 1,
- Subsignal("clk_p", Pins("T9"), IOStandard("TMDS_33")),
- Subsignal("clk_n", Pins("V9"), IOStandard("TMDS_33")),
- Subsignal("data0_p", Pins("R3"), IOStandard("TMDS_33")),
- Subsignal("data0_n", Pins("T3"), IOStandard("TMDS_33")),
- Subsignal("data1_p", Pins("T4"), IOStandard("TMDS_33")),
- Subsignal("data1_n", Pins("V4"), IOStandard("TMDS_33")),
- Subsignal("data2_p", Pins("N5"), IOStandard("TMDS_33")),
- Subsignal("data2_n", Pins("P6"), IOStandard("TMDS_33")),
- # Make sure JP2 is connected. Shared with JA.
- #Subsignal("scl", Pins("C13"), IOStandard("LVCMOS33")),
- #Subsignal("sda", Pins("A13"), IOStandard("LVCMOS33")),
+ Subsignal("scl", Pins("M16"), IOStandard("LVCMOS33")),
+ Subsignal("sda", Pins("M18"), IOStandard("LVCMOS33")),
),
]
-_io_vccb2_2v5 = []
+# Connectors ---------------------------------------------------------------------------------------
_connectors = [
- ## onboard VHDCI - FIXME
- # Can either run at 2.5V or 3.3V dependent on JP12 connector.
- # Channel 1 connects to P signals, Channel 2 to N signals
- # NET "VHDCIIO1<0>" LOC = "U16"; # Bank = 2, Pin name = IO_L2P_CMPCLK, Sch name = EXP-IO1_P
- # NET "VHDCIIO1<1>" LOC = "U15"; # Bank = 2, Pin name = *IO_L5P, Sch name = EXP-IO2_P
- # NET "VHDCIIO1<2>" LOC = "U13"; # Bank = 2, Pin name = IO_L14P_D11, Sch name = EXP-IO3_P
- # NET "VHDCIIO1<3>" LOC = "M11"; # Bank = 2, Pin name = *IO_L15P, Sch name = EXP-IO4_P
- # NET "VHDCIIO1<4>" LOC = "R11"; # Bank = 2, Pin name = IO_L16P, Sch name = EXP-IO5_P
- # NET "VHDCIIO1<5>" LOC = "T12"; # Bank = 2, Pin name = *IO_L19P, Sch name = EXP-IO6_P
- # NET "VHDCIIO1<6>" LOC = "N10"; # Bank = 2, Pin name = *IO_L20P, Sch name = EXP-IO7_P
- # NET "VHDCIIO1<7>" LOC = "M10"; # Bank = 2, Pin name = *IO_L22P, Sch name = EXP-IO8_P
- # NET "VHDCIIO1<8>" LOC = "U11"; # Bank = 2, Pin name = IO_L23P, Sch name = EXP-IO9_P
- # NET "VHDCIIO1<9>" LOC = "R10"; # Bank = 2, Pin name = IO_L29P_GCLK3, Sch name = EXP-IO10_P
- # NET "VHDCIIO1<10>" LOC = "U10"; # Bank = 2, Pin name = IO_L30P_GCLK1_D13, Sch name = EXP-IO11_P
- # NET "VHDCIIO1<11>" LOC = "R8"; # Bank = 2, Pin name = IO_L31P_GCLK31_D14, Sch name = EXP-IO12_P
- # NET "VHDCIIO1<12>" LOC = "M8"; # Bank = 2, Pin name = *IO_L40P, Sch name = EXP-IO13_P
- # NET "VHDCIIO1<13>" LOC = "U8"; # Bank = 2, Pin name = IO_L41P, Sch name = EXP-IO14_P
- # NET "VHDCIIO1<14>" LOC = "U7"; # Bank = 2, Pin name = IO_L43P, Sch name = EXP-IO15_P
- # NET "VHDCIIO1<15>" LOC = "N7"; # Bank = 2, Pin name = *IO_L44P, Sch name = EXP-IO16_P
- # NET "VHDCIIO1<16>" LOC = "T6"; # Bank = 2, Pin name = IO_L45P, Sch name = EXP-IO17_P
- # NET "VHDCIIO1<17>" LOC = "R7"; # Bank = 2, Pin name = IO_L46P, Sch name = EXP-IO18_P
- # NET "VHDCIIO1<18>" LOC = "N6"; # Bank = 2, Pin name = *IO_L47P, Sch name = EXP-IO19_P
- # NET "VHDCIIO1<19>" LOC = "U5"; # Bank = 2, Pin name = IO_49P_D3, Sch name = EXP-IO20_P
- # --
- # NET "VHDCIIO2<0>" LOC = "V16"; # Bank = 2, Pin name = IO_L2N_CMPMOSI, Sch name = EXP-IO1_N
- # NET "VHDCIIO2<1>" LOC = "V15"; # Bank = 2, Pin name = *IO_L5N, Sch name = EXP-IO2_N
- # NET "VHDCIIO2<2>" LOC = "V13"; # Bank = 2, Pin name = IO_L14N_D12, Sch name = EXP-IO3_N
- # NET "VHDCIIO2<3>" LOC = "N11"; # Bank = 2, Pin name = *IO_L15N, Sch name = EXP-IO4_N
- # NET "VHDCIIO2<4>" LOC = "T11"; # Bank = 2, Pin name = IO_L16N_VREF, Sch name = EXP-IO5_N
- # NET "VHDCIIO2<5>" LOC = "V12"; # Bank = 2, Pin name = *IO_L19N, Sch name = EXP-IO6_N
- # NET "VHDCIIO2<6>" LOC = "P11"; # Bank = 2, Pin name = *IO_L20N, Sch name = EXP-IO7_N
- # NET "VHDCIIO2<7>" LOC = "N9"; # Bank = 2, Pin name = *IO_L22N, Sch name = EXP-IO8_N
- # NET "VHDCIIO2<8>" LOC = "V11"; # Bank = 2, Pin name = IO_L23N, Sch name = EXP-IO9_N
- # NET "VHDCIIO2<9>" LOC = "T10"; # Bank = 2, Pin name = IO_L29N_GCLK2, Sch name = EXP-IO10_N
- # NET "VHDCIIO2<10>" LOC = "V10"; # Bank = 2, Pin name = IO_L30N_GCLK0_USERCCLK, Sch name = EXP-IO11_N
- # NET "VHDCIIO2<11>" LOC = "T8"; # Bank = 2, Pin name = IO_L31N_GCLK30_D15, Sch name = EXP-IO12_N
- # NET "VHDCIIO2<12>" LOC = "N8"; # Bank = 2, Pin name = *IO_L40N, Sch name = EXP-IO13_N
- # NET "VHDCIIO2<13>" LOC = "V8"; # Bank = 2, Pin name = IO_L41N_VREF, Sch name = EXP-IO14_N
- # NET "VHDCIIO2<14>" LOC = "V7"; # Bank = 2, Pin name = IO_L43N, Sch name = EXP-IO15_N
- # NET "VHDCIIO2<15>" LOC = "P8"; # Bank = 2, Pin name = *IO_L44N, Sch name = EXP-IO16_N
- # NET "VHDCIIO2<16>" LOC = "V6"; # Bank = 2, Pin name = IO_L45N, Sch name = EXP-IO17_N
- # NET "VHDCIIO2<17>" LOC = "T7"; # Bank = 2, Pin name = IO_L46N, Sch name = EXP-IO18_N
- # NET "VHDCIIO2<18>" LOC = "P7"; # Bank = 2, Pin name = *IO_L47N, Sch name = EXP-IO19_N
- # NET "VHDCIIO2<19>" LOC = "V5"; # Bank = 2, Pin name = IO_49N_D4, Sch name = EXP-IO20_N
("VHDCI",
{
- "EXP-IO1_P": "U16",
- "EXP-IO2_P": "U15",
- "EXP-IO3_P": "U13",
- "EXP-IO4_P": "M11",
- "EXP-IO5_P": "R11",
- "EXP-IO6_P": "T12",
- "EXP-IO7_P": "N10",
- "EXP-IO8_P": "M10",
- "EXP-IO9_P": "U11",
- "EXP-IO10_P": "R10",
- "EXP-IO11_P": "U10",
- "EXP-IO12_P": "R8",
- "EXP-IO13_P": "M8",
- "EXP-IO14_P": "U8",
- "EXP-IO15_P": "U7",
- "EXP-IO16_P": "N7",
- "EXP-IO17_P": "T6",
- "EXP-IO18_P": "R7",
- "EXP-IO19_P": "N6",
- "EXP-IO20_P": "U5",
- "EXP-IO1_N": "V16",
- "EXP-IO2_N": "V15",
- "EXP-IO3_N": "V13",
- "EXP-IO4_N": "N11",
- "EXP-IO5_N": "T11",
- "EXP-IO6_N": "V12",
- "EXP-IO7_N": "P11",
- "EXP-IO8_N": "N9",
- "EXP-IO9_N": "V11",
- "EXP-IO10_N": "T10",
- "EXP-IO11_N": "V10",
- "EXP-IO12_N": "T8",
- "EXP-IO13_N": "N8",
- "EXP-IO14_N": "V8",
- "EXP-IO15_N": "V7",
- "EXP-IO16_N": "P8",
- "EXP-IO17_N": "V6",
- "EXP-IO18_N": "T7",
- "EXP-IO19_N": "P7",
- "EXP-IO20_N": "V5",
+ "EXP-IO1_P" : "U16",
+ "EXP-IO2_P" : "U15",
+ "EXP-IO3_P" : "U13",
+ "EXP-IO4_P" : "M11",
+ "EXP-IO5_P" : "R11",
+ "EXP-IO6_P" : "T12",
+ "EXP-IO7_P" : "N10",
+ "EXP-IO8_P" : "M10",
+ "EXP-IO9_P" : "U11",
+ "EXP-IO10_P" : "R10",
+ "EXP-IO11_P" : "U10",
+ "EXP-IO12_P" : "R8",
+ "EXP-IO13_P" : "M8",
+ "EXP-IO14_P" : "U8",
+ "EXP-IO15_P" : "U7",
+ "EXP-IO16_P" : "N7",
+ "EXP-IO17_P" : "T6",
+ "EXP-IO18_P" : "R7",
+ "EXP-IO19_P" : "N6",
+ "EXP-IO20_P" : "U5",
+ "EXP-IO1_N" : "V16",
+ "EXP-IO2_N" : "V15",
+ "EXP-IO3_N" : "V13",
+ "EXP-IO4_N" : "N11",
+ "EXP-IO5_N" : "T11",
+ "EXP-IO6_N" : "V12",
+ "EXP-IO7_N" : "P11",
+ "EXP-IO8_N" : "N9",
+ "EXP-IO9_N" : "V11",
+ "EXP-IO10_N" : "T10",
+ "EXP-IO11_N" : "V10",
+ "EXP-IO12_N" : "T8",
+ "EXP-IO13_N" : "N8",
+ "EXP-IO14_N" : "V8",
+ "EXP-IO15_N" : "V7",
+ "EXP-IO16_N" : "P8",
+ "EXP-IO17_N" : "V6",
+ "EXP-IO18_N" : "T7",
+ "EXP-IO19_N" : "P7",
+ "EXP-IO20_N" : "V5",
}
),
]
-
-_hdmi_infos = {
- "HDMI_IN0_MNEMONIC": "J1",
- "HDMI_IN0_DESCRIPTION" : (
- " Type A connector, marked as J1, on side with USB connectors.\\r\\n"
- " To use J1, make sure:\\r\\n"
- " * JP4 has a jumper (it connects / disconnects 5V to HDMI pin 18).\\r\\n"
- " * JP2 (marked only as SDA/SCL - not to be confused with JP6 and JP6)\\r\\n"
- " has *two* jumpers (horizontally).\\r\\n"
- " * JP5 has a jumper (it enables the HDMI input buffer).\\r\\n"
- ),
-
- "HDMI_IN1_MNEMONIC": "J3",
- "HDMI_IN1_DESCRIPTION" : (
- " Type A connector, marked as J3, between audio connectors and\\r\\n"
- " Ethernet RJ45 connector.\\r\\n"
- " To use J3, make sure:\\r\\n"
- " * JP8 has a jumper (it connects / disconnects 5V to HDMI pin 18)\\r\\n"
- " * JP6 and JP7 do *not* have any jumpers (it connect J3's and J2's\\r\\n"
- " EDID lines together).\\r\\n"
- ),
-
- "HDMI_OUT0_MNEMONIC": "J2",
- "HDMI_OUT0_DESCRIPTION" : (
- " Type A connector, marked as J2, next to the power connector.\\r\\n"
- " To use J2, make sure:\\r\\n"
- " * JP8 has a jumper (it connects / disconnects 5V to HDMI pin 18)\\r\\n"
- " * JP6 and JP7 do *not* have any jumpers (it connect J3's and J2's\\r\\n"
- " EDID lines together).\\r\\n"
- ),
-
- "HDMI_OUT1_MNEMONIC": "JB",
- "HDMI_OUT1_DESCRIPTION" : (
- " Micro-D connector, marked as JB, on the same side as switches\\r\\n"
- " + LEDs but on the underside of the board below MOD connector.\\r\\n"
- " Works as either output or input because it isn't buffered.\\r\\n"
- " Also often referred to as 'JA'.\\r\\n"
- )
-}
-
+# Platform -----------------------------------------------------------------------------------------
class Platform(XilinxPlatform):
- name = "atlys"
- default_clk_name = "clk100"
- default_clk_period = 10.0
- hdmi_infos = _hdmi_infos
+ default_clk_name = "clk100"
+ default_clk_period = 1e9/100e6
- # https://reference.digilentinc.com/atlys:atlys:refmanual#flash_memory
- # The Atlys has a XC6SLX45 which bitstream takes up ~12Mbit (1484472 bytes)
- # 0x200000 offset (16Mbit) gives plenty of space
- gateware_size = 0x200000
-
- # Micron N25Q128 (ID 0x0018ba20)
- # FIXME: Create a "spi flash module" object in the same way we have SDRAM
- # module objects.
- spiflash_model = "n25q128"
- spiflash_read_dummy_bits = 10
- spiflash_clock_div = 4
- spiflash_total_size = int((128/8)*1024*1024) # 128Mbit
- spiflash_page_size = 256
- spiflash_sector_size = 0x10000
-
- def __init__(self, programmer="openocd", vccb2_voltage="VCC3V3"):
- # Some IO configurations only work at certain vccb2 voltages.
- if vccb2_voltage == "VCC3V3":
- _io.extend(_io_vccb2_3v3)
- elif vccb2_voltage == "VCC2V5":
- _io.extend(_io_vccb2_2v5)
- else:
- raise SystemError("Unknown vccb2_voltage=%r" % vccb2_voltage)
-
- # Resolve the LVCMOS_BANK2 voltage level before anything uses the _io
- # definition.
- LVCMOS_BANK2.set(vccb2_voltage)
-
- # XC6SLX45-2CSG324C
+ def __init__(self,):
XilinxPlatform.__init__(self, "xc6slx45-csg324-3", _io, _connectors)
- self.programmer = programmer
-
- # FPGA AUX is connected to the 3.3V supply on the Atlys
self.add_platform_command("""CONFIG VCCAUX="3.3";""")
def create_programmer(self):
- # Preferred programmer - Needs ixo-usb-jtag and latest openocd.
- proxy="bscan_spi_{}.bit".format(self.device.split('-')[0])
- if self.programmer == "openocd":
- return OpenOCD(config="board/digilent_atlys.cfg", flash_proxy_basename=proxy)
- # Alternative programmers - not regularly tested.
- elif self.programmer == "xc3sprog":
- return XC3SProg("jtaghs1_fast", "bscan_spi_digilent_atlys.bit")
- elif self.programmer == "impact":
- return iMPACT()
- elif self.programmer == "adept":
- return Adept("Atlys", 0)
- elif self.programmer == "fpgalink":
- from mibuild.fpgalink_programmer import FPGALink
- return FPGALink("1443:0007")
- elif self.programmer == "urjtag":
- return UrJTAG(cable="USBBlaster", pld="spartan-6")
- else:
- raise ValueError("{} programmer is not supported".format(self.programmer))
+ return iMPACT()
def do_finalize(self, fragment):
XilinxPlatform.do_finalize(self, fragment)
-
- # The oscillator clock sources.
- try:
- self.add_period_constraint(self.lookup_request("clk100"), 10.0)
- except ConstraintError:
- pass
-
- # HDMI input clock pins.
- for i in range(2):
- try:
- self.add_period_constraint(self.lookup_request("hdmi_in", i).clk_p, 12)
- except ConstraintError:
- pass
-
- # Ethernet input clock pins.
- try:
- self.add_period_constraint(self.lookup_request("eth_clocks").rx, 40.0)
- except ConstraintError:
- pass
-
- # USB input clock pins.
- try:
- self.add_period_constraint(self.lookup_request("fx2").ifclk, 10)
- except ConstraintError:
- pass
-
-
+ self.add_period_constraint(self.lookup_request("clk100", loose=True), 1e9/100e6)
+ self.add_period_constraint(self.lookup_request("hdmi_in:clk_p", 0, loose=True), 1e9/74.25e6)
+ self.add_period_constraint(self.lookup_request("hdmi_in:clk_p", 1, loose=True), 1e9/74.25e6)
+ self.add_period_constraint(self.lookup_request("eth_clocks:rx", loose=True), 1e9/25e6)
+ self.add_period_constraint(self.lookup_request("fx2:ifclk", loose=True), 1e9/100e6)
diff --git a/litex_boards/targets/digilent_atlys.py b/litex_boards/targets/digilent_atlys.py
old mode 100644
new mode 100755
index f346e55..f14e8dc
--- a/litex_boards/targets/digilent_atlys.py
+++ b/litex_boards/targets/digilent_atlys.py
@@ -21,20 +21,12 @@ from migen.genlib.resetsync import AsyncResetSynchronizer
from litex_boards.platforms import atlys
from litex.soc.integration.soc_core import *
-from litex.soc.integration.soc_sdram import *
from litex.soc.integration.builder import *
from litex.soc.cores.led import LedChaser
from litedram.modules import MT47H64M16
from litedram.phy import s6ddrphy
-from liteeth.phy import LiteEthPHYGMII
-
-# LiteEthPHY
-#from liteeth.phy.mii import LiteEthMAC
-
-from liteeth.phy.mii import LiteEthPHYMII
-
# CRG ----------------------------------------------------------------------------------------------
class _CRG(Module):
@@ -58,8 +50,8 @@ class _CRG(Module):
i_I=clk100, o_DIVCLK=clk100b)
# PLL --------------------------------------------------------------------------------------
- pll_lckd = Signal()
- pll_fb = Signal()
+ pll_lckd = Signal()
+ pll_fb = Signal()
pll_sdram_full = Signal()
pll_sdram_half_a = Signal()
pll_sdram_half_b = Signal()
@@ -120,10 +112,6 @@ class _CRG(Module):
# System clock
self.specials += Instance("BUFG", i_I=pll_sys, o_O=self.cd_sys.clk)
self.comb += self.cd_por.clk.eq(self.cd_sys.clk)
-
- print("-- self.cd_sys.clk:")
- print( self.cd_sys.clk)
-
self.specials += AsyncResetSynchronizer(self.cd_sys, ~pll_lckd | (por > 0))
# SDRAM clocks -----------------------------------------------------------------------------
@@ -151,32 +139,18 @@ class _CRG(Module):
output_clk = Signal()
clk = platform.request("ddram_clock")
self.specials += Instance("ODDR2", p_DDR_ALIGNMENT="NONE",
- p_INIT=0, p_SRTYPE="SYNC",
- i_D0=1, i_D1=0, i_S=0, i_R=0, i_CE=1,
- i_C0=clk_sdram_half_shifted,
- i_C1=~clk_sdram_half_shifted,
- o_Q=output_clk)
+ p_INIT=0, p_SRTYPE="SYNC",
+ i_D0=1, i_D1=0, i_S=0, i_R=0, i_CE=1,
+ i_C0=clk_sdram_half_shifted,
+ i_C1=~clk_sdram_half_shifted,
+ o_Q=output_clk)
self.specials += Instance("OBUFDS", i_I=output_clk, o_O=clk.p, o_OB=clk.n)
- #
- #
- # self.specials += Instance("ODDR2", p_DDR_ALIGNMENT="NONE",
- # p_INIT=0, p_SRTYPE="SYNC",
- # i_D0=1, i_D1=0, i_S=0, i_R=0, i_CE=1,
- # i_C0=clk_sdram_half_shifted,
- # i_C1=~clk_sdram_half_shifted,
- # o_Q=clk.p)
- # self.specials += Instance("ODDR2", p_DDR_ALIGNMENT="NONE",
- # p_INIT=0, p_SRTYPE="SYNC",
- # i_D0=0, i_D1=1, i_S=0, i_R=0, i_CE=1,
- # i_C0=clk_sdram_half_shifted,
- # i_C1=~clk_sdram_half_shifted,
- # o_Q=clk.n)
# BaseSoC ------------------------------------------------------------------------------------------
class BaseSoC(SoCCore):
def __init__(self, with_ethernet=True, with_etherbone=False, eth_phy=0, **kwargs):
- sys_clk_freq = int(75e6) # Fraction(75*1000*1000,1) # (83 + Fraction(1, 3))*1000*1000
+ sys_clk_freq = int(75e6)
platform = atlys.Platform()
# SoCCore ----------------------------------------------------------------------------------
@@ -189,7 +163,7 @@ class BaseSoC(SoCCore):
self.submodules.crg = _CRG(platform, sys_clk_freq)
self.platform.add_period_constraint(self.crg.cd_sys.clk, 1e9/sys_clk_freq)
- # DDR2 SDRAM ------------------------------------------------------------------------------
+ # DDR2 SDRAM -------------------------------------------------------------------------------
if not self.integrated_main_ram_size:
self.submodules.ddrphy = s6ddrphy.S6HalfRateDDRPHY(platform.request("ddram"),
memtype = "DDR2",
@@ -200,15 +174,10 @@ class BaseSoC(SoCCore):
self.ddrphy.clk4x_wr_strb.eq(self.crg.clk4x_wr_strb),
self.ddrphy.clk4x_rd_strb.eq(self.crg.clk4x_rd_strb),
]
- self.add_csr("ddrphy")
self.add_sdram("sdram",
- phy = self.ddrphy,
- module = MT47H64M16(sys_clk_freq, "1:2"),
- origin = self.mem_map["main_ram"],
- size = kwargs.get("max_sdram_size", 0x4000000), # 0x100000000),
- l2_cache_size = kwargs.get("l2_size", 8192),
- l2_cache_min_data_width = kwargs.get("min_l2_data_width", 128),
- l2_cache_reverse = True
+ phy = self.ddrphy,
+ module = MT47H64M16(sys_clk_freq, "1:2"),
+ l2_cache_size = kwargs.get("l2_size", 8192),
)
# Ethernet / Etherbone ---------------------------------------------------------------------
@@ -218,35 +187,20 @@ class BaseSoC(SoCCore):
clock_pads = self.platform.request("eth_clocks", eth_phy),
pads = self.platform.request("eth", eth_phy),
clk_freq = int(self.sys_clk_freq))
- self.add_csr("ethphy")
-
if with_ethernet:
self.add_ethernet(phy=self.ethphy)
if with_etherbone:
- print("etherbone")
self.add_etherbone(phy=self.ethphy)
-
self.ethphy.crg.cd_eth_rx.clk.attr.add("keep")
self.ethphy.crg.cd_eth_tx.clk.attr.add("keep")
-
- # FIXME: This is probably too tight?
-# self.platform.add_period_constraint(self.ethphy.crg.cd_eth_rx.clk, 8.0)
-
-
self.platform.add_platform_command("""
-# FIXME: ERROR:Place:1108 - A clock IOB / BUFGMUX clock component pair have
-# been found that are not placed at an optimal clock IOB / BUFGMUX site pair.
-# The clock IOB component <eth_clocks_rx> is placed at site <K15>.
NET "{eth_clocks_rx}" CLOCK_DEDICATED_ROUTE = FALSE;
-# The IOB component <eth_clocks_tx> is placed at site <K16>.
NET "{eth_clocks_tx}" CLOCK_DEDICATED_ROUTE = FALSE;
""",
eth_clocks_rx=platform.lookup_request("eth_clocks").rx,
eth_clocks_tx=platform.lookup_request("eth_clocks").tx,
)
-
- # self.add_interrupt("ethmac")
# Leds -------------------------------------------------------------------------------------
self.submodules.leds = LedChaser(
pads = platform.request_all("user_led"),
@@ -263,10 +217,10 @@ def main():
parser.add_argument("--with-etherbone", action="store_true", help="Enable Etherbone support")
builder_args(parser)
- soc_sdram_args(parser)
+ soc_core_args(parser)
args = parser.parse_args()
- soc = BaseSoC(**soc_sdram_argdict(args))
+ soc = BaseSoC(**soc_core_argdict(args))
builder = Builder(soc, **builder_argdict(args), )
builder.build(run=args.build)