micropython control of SPI works (as far as I can tell)

gateware/extio.py

@@ -49,7 +49,12 @@ class Waveform(LiteXModule):
                 origin= 0x18,
                 bitwidth= 16,
                 rw= True,
-            )
+            ),
+            "force_stop" : Register (
+                origin=0x1C,
+                bitwidth=1,
+                rw=True,
+            ),
     }
 
     width = 0x20
@@ -85,6 +90,7 @@ class Waveform(LiteXModule):
         wform_size = Signal(counter_max_wid)
         timer = Signal(timer_wid)
         timer_spacing = Signal(timer_wid)
+        force_stop = Signal()
 
         self.sync += If(b.cyc & b.stb & ~b.ack,
                 Case(b.adr, {
@@ -118,6 +124,11 @@ class Waveform(LiteXModule):
                         ).Else(
                             b.dat_r[0:timer_wid].eq(timer_spacing),
                         ),
+                    0x1C: If(b.we,
+                            force_stop.eq(b.dat_w[0]),
+                        ).Else(
+                            b.dat_r[0].eq(force_stop),
+                        ),
                         # (W)A(V)EFO(RM)
                     "default": b.dat_r.eq(0xAEF0AEF0),
                     }
@@ -136,6 +147,7 @@ class Waveform(LiteXModule):
                 i_clk = ClockSignal(),
 
                 i_run = run,
+                i_force_stop = force_stop,
                 o_cntr = cntr,
                 i_do_loop = do_loop,
                 o_finished = finished,
@@ -190,11 +202,11 @@ class SPIMaster(Module):
     width = 0x20
 
     public_registers = {
-            # The first bit is the "finished" bit, when the master is
-            # armed and finished with a transmission.
-            # The second bit is the "ready" bit, when the master is
+            # The first bit is the "ready" bit, when the master is
             # not armed and ready to be armed.
-            "ready_or_finished": Register(
+            # The second bit is the "finished" bit, when the master is
+            # armed and finished with a transmission.
+            "finished_or_ready": Register(
                 origin= 0,
                 bitwidth= 2,
                 rw=False,
@@ -224,7 +236,7 @@ class SPIMaster(Module):
 
             # Same as ready_or_finished, but halts until ready or finished
             # goes high. Dangerous, might cause cores to hang!
-            "wait_ready_or_finished": Register(
+            "wait_finished_or_ready": Register(
                 origin=0x10,
                 bitwidth=2,
                 rw= False,
@@ -333,7 +345,8 @@ class SPIMaster(Module):
             p_PHASE = phase,
 
             i_clk = ClockSignal(),
-            i_rst_L = rst,
+            # module_reset is active high
+            i_rst_L = ~rst,
             i_miso = miso,
             o_mosi = mosi,
             o_sck_wire = sck,

gateware/rtl/waveform/waveform.v

@@ -15,6 +15,7 @@ module waveform #(
 
 	/* Waveform output control */
 	input run,
+	input force_stop,
 	output reg[COUNTER_MAX_WID-1:0] cntr,
 	input do_loop,
 	output reg finished,
@@ -57,7 +58,9 @@ localparam WAIT_PERIOD = 13;
 
 reg [4-1:0] state = CHECK_START;
 
-always @ (posedge clk) case (state)
+always @ (posedge clk) if (force_stop) begin
+	state <= CHECK_START;
+end else case (state)
 CHECK_START: if (run) begin
 		cntr <= 0;
 		ready <= 0;

gateware/rtl/waveform/waveform_sim.v

@@ -15,6 +15,7 @@ module waveform_sim #(
 
 	/* Waveform output control */
 	input run,
+	input force_stop,
 	output [COUNTER_MAX_WID-1:0] cntr,
 	input do_loop,
 	output finished,
@@ -52,6 +53,7 @@ waveform #(
 ) wf (
 	.clk(clk),
 	.run(run),
+	.force_stop(force_stop),
 	.cntr(cntr),
 	.do_loop(do_loop),
 	.finished(finished),

gateware/soc.py

@@ -274,7 +274,7 @@ class UpsilonSoC(SoCCore):
         def f(csrs):
             wid = kwargs["spi_wid"]
             origin = csrs["memories"][name.lower() + "_pi"]['base']
-            return f'{name} = SPI({wid}, {origin}, {spi.mmio(origin)})'
+            return f'{name} = SPI({wid}, {name}_PI, {origin}, {spi.mmio(origin)})'
         self.mmio_closures.append(f)
 
         return spi, pi

linux/spi.py

@@ -1,6 +1,26 @@
 from registers import *
 
 class SPI(RegisterRegion):
-    def __init__(self, spiwid, origin, **regs):
+    def __init__(self, spiwid, spi_PI, origin, **regs):
         self.spiwid = spiwid
+        self.spi_PI = spi_PI
         super().__init__(origin, **regs)
+
+    def send(self, val, force=False):
+        if self.spi_PI.v != 0 and not force:
+            raise Exception("SPI is controlled by another master")
+
+        self.spi_PI.v = 0
+
+        self.arm.v = 0
+        while self.finished_or_ready.v == 0:
+            pass
+
+        self.to_slave.v = val
+        self.arm.v = 1
+        while self.finished_or_ready.v == 0:
+            pass
+
+        read_val = self.from_slave.v
+        self.arm.v = 0
+        return read_val

linux/waveform.py

@@ -38,6 +38,10 @@ class Waveform(Immutable):
         while self.regs.finished_or_ready == 0:
             pass
 
+    def force_stop(self):
+        self.regs.force_stop = 1
+        selff.regs.force_stop = 0
+
     def dump(self):
         """ Dump contents of control registers. """
         return self.regs.dump()