spi/spi_master.v

174 lines
3.4 KiB
Verilog

/* (c) Peter McGoron 2022 v0.2
* This Source Code Form is subject to the terms of the Mozilla Public
* License, v.2.0. If a copy of the MPL was not distributed with this
* file, You can obtain one at https://mozilla.org/MPL/2.0/.
*/
module
`ifdef SPI_MASTER_NO_READ
spi_master_no_read
`else
`ifdef SPI_MASTER_NO_WRITE
spi_master_no_write
`else
spi_master
`endif
`endif
#(
parameter WID = 24, // Width of bits per transaction.
parameter WID_LEN = 5, // Length in bits required to store WID
parameter CYCLE_HALF_WAIT = 1, // Half of the wait time of a cycle minus 1.
// One SCK cycle is 2*(CYCLE_HALF_WAIT + 1) clock cycles.
parameter TIMER_LEN = 3, // Length in bits required to store CYCLE_HALF_WAIT
parameter POLARITY = 0, // 0 = sck idle low, 1 = sck idle high
parameter PHASE = 0 // 0 = rising-read falling-write, 1 = rising-write falling-read.
)
(
input clk,
`ifndef SPI_MASTER_NO_READ
output reg [WID-1:0] from_slave,
input miso,
`endif
`ifndef SPI_MASTER_NO_WRITE
input [WID-1:0] to_slave,
output reg mosi,
`endif
output reg sck_wire,
output reg finished,
input arm
);
parameter WAIT_ON_ARM = 0;
parameter ON_CYCLE = 1;
parameter CYCLE_WAIT = 2;
parameter WAIT_FINISHED = 3;
reg [1:0] state = WAIT_ON_ARM;
reg [WID_LEN-1:0] bit_counter = 0;
reg [TIMER_LEN-1:0] timer = 0;
`ifndef SPI_MASTER_NO_WRITE
reg [WID-1:0] send_buf = 0;
`endif
reg sck = 0;
assign sck_wire = sck;
task idle_state();
if (POLARITY == 0) begin
sck <= 0;
end else begin
sck <= 1;
end
`ifndef SPI_MASTER_NO_WRITE
mosi <= 0;
`endif
timer <= 0;
bit_counter <= 0;
endtask
task read_data();
`ifndef SPI_MASTER_NO_READ
from_slave <= from_slave << 1;
from_slave[0] <= miso;
`endif
endtask
task write_data();
`ifndef SPI_MASTER_NO_WRITE
mosi <= send_buf[WID-1];
send_buf <= send_buf << 1;
`endif
endtask
task setup_bits();
/* at Mode 00, the transmission starts with
* a rising edge, and at mode 11, it starts with a falling
* edge. For both modes, these are READs.
*
* For mode 01 and mode 10, the first action is a WRITE.
*/
if (POLARITY == PHASE) begin
`ifndef SPI_MASTER_NO_WRITE
mosi <= to_slave[WID-1];
send_buf <= to_slave << 1;
`endif
state <= CYCLE_WAIT;
end else begin
`ifndef SPI_MASTER_NO_WRITE
send_buf <= to_slave;
`endif
state <= ON_CYCLE;
end
endtask
task cycle_change();
// Stop transfer when the clock returns to its original polarity.
if (bit_counter == WID[WID_LEN-1:0] && sck == POLARITY[0]) begin
state <= WAIT_FINISHED;
end else begin
sck <= !sck;
state <= ON_CYCLE;
end
endtask
always @ (posedge clk) begin
case (state)
WAIT_ON_ARM: begin
if (!arm) begin
idle_state();
finished <= 0;
end else begin
setup_bits();
end
end
ON_CYCLE: begin
if (sck) begin // rising edge
if (PHASE == 1) begin
write_data();
end else begin
read_data();
end
if (POLARITY == 0) begin
bit_counter <= bit_counter + 1;
end
end else begin // falling edge
if (PHASE == 1) begin
read_data();
end else begin
write_data();
end
if (POLARITY == 1) begin
bit_counter <= bit_counter + 1;
end
end
if (CYCLE_HALF_WAIT == 0) begin
cycle_change();
end else begin
state <= CYCLE_WAIT;
end
end
CYCLE_WAIT: begin
if (timer == CYCLE_HALF_WAIT) begin
timer <= 1;
cycle_change();
end else begin
timer <= timer + 1;
end
end
WAIT_FINISHED: begin
finished <= 1;
idle_state();
if (!arm) begin
state <= WAIT_ON_ARM;
end
end
endcase
end
endmodule