Rough Draft

Signed-off-by: Joshua Fife <jpfife17@gmail.com>

docs/index.rst

@@ -32,3 +32,4 @@ currently targeting chips from multiple vendors, e.g.:
    getting-symbiflow
    building-examples
    running-examples
+   personal-designs

docs/personal-designs.rst

@@ -0,0 +1,102 @@
+Using Symbiflow to upload your own designs
+===========================================
+
+This section describes how you can upload you're own designs to an FPGA from start to finish using only open source tools.
+
+Prepareing your environment
+----------------------------
+Before building any example, set the installation directory to match what you
+set it to earlier, for example:
+
+.. code-block:: bash
+   :name: export-install-dir
+
+   export INSTALL_DIR=~/opt/symbiflow
+
+Select your FPGA family:
+
+.. tabs::
+
+   .. group-tab:: Artix-7
+
+      .. code-block:: bash
+         :name: fpga-fam-xc7
+
+         FPGA_FAM="xc7"
+
+   .. group-tab:: EOS S3
+
+      .. code-block:: bash
+         :name: fpga-fam-eos-s3
+
+         FPGA_FAM="eos-s3"
+
+Next, prepare the environment:
+
+.. code-block:: bash
+   :name: conda-prep-env
+
+   export PATH="$INSTALL_DIR/$FPGA_FAM/install/bin:$PATH";
+   source "$INSTALL_DIR/$FPGA_FAM/conda/etc/profile.d/conda.sh"
+
+Finally, enter your working Conda environment:
+
+.. code-block:: bash
+   :name: conda-act-env
+
+   conda activate $FPGA_FAM
+
+
+File pre-requisits
+-------------------
+
+
+
+Creating the Makefile
+----------------------
+
+
+Building your personal projects
+-------------------------------
+Before you begin building your design navigate to the directory where you have stored your Makefile, virilog, and .xdc files:
+
+.. code-block:: bash
+   :name: your-directory
+
+   cd <path to your directory>
+
+Then, to build your design, simply run make on your current dirrectory: 
+
+.. code-block:: bash
+   :name: run-make
+
+   make -C .
+
+
+If your design builds withought error, the bitstream can be found in the following location:
+
+.. code-block:: bash
+
+   cd build/<board>
+
+Finaly, for **Arty and Basys3**, you can upload the design with:
+
+.. code-block:: bash
+
+   openocd -f ${INSTALL_DIR}/${FPGA_FAM}/conda/envs/${FPGA_FAM}/share/openocd/scripts/board/digilent_arty.cfg -c "init; pld load 0 top.bit; exit"
+
+
+.. tip::
+    Many of the commands needed to build a project are run many times withought deviation. You might consider adding a few aliases or even a few bash functions to your .bashrc file to save yourself some typing or repeated coppy/paste. 
+    For example, instead of using the cumbersome command used to upload the bitsream to arty or basys3 every time, you could just add the following lines to your bashrc file:
+    
+    .. code-block:: bash
+       :name: bash-functions
+
+        symbi_bit() { 
+        #Creates and downloads the bitstream to Basys 3 or Arty boards:
+        openocd -f /home/chem3000/opt/symbiflow/xc7/conda/envs/xc7/share/openocd/scripts/board/digilent_arty.cfg -c "init; pld load 0 top.bit; exit"
+       }
+
+    Now whenever you need to download a bitstream to the arty or basysis you can simply type ``symbi_bit`` into the terminal and hit enter.
+