f4pga/source/toolchain-desc/yosys.rst

410 lines
15 KiB
ReStructuredText
Raw Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

Yosys
=====
Yosys is a Free and Open Source Verilog HDL synthesis tool. It was designed
to be highly extensible and multiplatform. In SymbiFlow toolchain,
it is responsible for the whole synthesis process described in `FPGA Design Flow
<./design-flow.html>`_
It is not necessary to call Yosys directly using the SymbiFlow
toolchain. Nevertheless, the following description, should provide
sufficient introduction to Yosys usage inside the project.
It is also a good starting point for a deeper understanding of the whole
toolchain.
Short description
-----------------
Yosys consists of several subsystems. Most distinguishable are the
first and last ones used in the synthesis process, called *frontend*
and *backend* respectively. Intermediate subsystems are called *passes*.
The *frontend* is responsible for changing the Verilog input file into
an internal Yosys, representation which is common for all *passes* used
by the program. The *passes* are responsible for a variety of optimizations
(``opt_``) and simplifications (``proc_``).
Two *passes*, that are worth
to mention separately are ``ABC`` and ``techmap``. The first one optimizes
logic functions from the design and assigns obtained results into Look Up Tables
(LUTs) of chosen width. The second mentioned *pass* - ``techmap``
is responsible for mapping the synthesized design from Yosys internal
blocks to the primitives used by the implementation tool.
Recommended synthesis flows for different FPGAs are combined into
macros i.e. ``synth_ice40`` (for Lattice iCE40 FPGA) or ``synth_xilinx``
(for Xilinx 7-series FPGAs).
The *backend* on the other hand, is responsible
for converting internal Yosys representation into one of the standardized
formats. Symbiflow uses ``.eblif`` as its output file format.
Usage in Toolchain
------------------
All operations performed by Yosys are written in ``.tcl`` script. Commands used
in the scripts are responsible for preparing output file to match with the
expectations of other toolchain tools.
There is no need to change it even for big designs.
An example configuration script can be found below:
.. code-block:: tcl
yosys -import
synth_ice40 -nocarry
opt_expr -undriven
opt_clean
setundef -zero -params
write_blif -attr -cname -param $::env(OUT_EBLIF)
write_verilog $::env(OUT_SYNTH_V)
It can be seen that this script performs a platform-specific process of
synthesis, some optimization steps (``opt_`` commands), and writes the final file in
``.eblif`` and Verilog formats. Yosys synthesis configuration scripts are platform-specific
and can by found in ``<platform-dir>/yosys/synth.tcl``
in the `Symbiflow Architecture Definitions <https://github.com/SymbiFlow/symbiflow-arch-defs>`_
repository.
To understand performed operations, view the log file. It is usually generated
in the project build directory. It should be named ``top.eblif.log``.
Output analysis
---------------
Input file:
.. code-block:: verilog
module top (
input clk,
output LD7,
);
localparam BITS = 1;
localparam LOG2DELAY = 25;
reg [BITS+LOG2DELAY-1:0] counter = 0;
always @(posedge clk) begin
counter <= counter + 1;
end
assign {LD7} = counter >> LOG2DELAY;
endmodule
after synthesis is described only with use of primitives appropriate for
chosen platform:
.. code-block:: verilog
module top(clk, LD7);
wire [25:0] _000_;
wire _001_;
...
FDRE_ZINI #(
.IS_C_INVERTED(1'h0),
.ZINI(1'h1)
) _073_ (
.C(clk),
.CE(_012_),
.D(_000_[0]),
.Q(counter[0]),
.R(_013_)
);
...
SR_GND _150_ (
.GND(_062_)
);
assign _003_[25:0] = _000_;
assign counter[25] = LD7;
endmodule
The same structure is described by the ``.eblif`` file.
Technology mapping in SymbiFlow toolchain
-----------------------------------------
.. _Xilinx 7 Series FPGAs Clocking Resources User Guide: https://www.xilinx.com/support/documentation/user_guides/ug472_7Series_Clocking.pdf#page=38
.. _VTR FPGA Architecture Description: https://docs.verilogtorouting.org/en/latest/arch/
.. _techmap section in the Yosys Manual: http://www.clifford.at/yosys/files/yosys_manual.pdf#page=153
It is important to understand the connection between the synthesis and
implementation tools used in the SymbiFlow toolchain. As mentioned before,
synthesis tools like Yosys take the design description from the source files
and convert them into a netlist that consists of the primitives used by
the implementation tool. Usually, to support multiple implementation tools,
an additional intermediate representation of FPGA primitives is provided.
The process of translating the primitives from the synthesis
tools internal representation to the specific primitives used in the
implementation tools is called technology mapping (or techmapping).
Technology mapping for VPR
--------------------------
As mentioned before, VPR is one of the implementation tools (often referred to
as Place & Route or P&R tools) used in SymbiFlow. By default, the SymbiFlow
toolchain uses it during bitstream generation for, i.e., Xilinx 7-Series
devices. Since the architecture models for this FPGA family were created from
scratch, appropriate techmaps were needed to instruct Yosys on translating
the primitives to the versions compatible with VPR.
The clock buffers used in the 7-Series devices are a good example for explaining
the techmapping process. Generally, as stated in the
`Xilinx 7 Series FPGAs Clocking Resources User Guide`_, a designer has various
buffer types that they can use in designs:
- ``BUFGCTRL``
- ``BUFG``
- ``BUFGCE``
- ``BUFGCE_1``
- ``BUFGMUX``
- ``BUFGMUX_1``
- ``BUFGMUX_CTRL``
Nevertheless, the actual chips consist only of the ``BUFGCTRL`` primitives,
which are the most universal and can function as other clock buffer
primitives from the Xilinx manual. Because of that, only one architecture model
is required for VPR. The rest of the primitives is mapped to this general
buffer during the techmapping process. The model of ``BUFGCTRL`` primitive used
by VPR is called ``BUFGCTR_VPR`` (More information about the architecture
modeling in VPR can be found in the `VTR FPGA Architecture Description`_).
Support for particular primitive in VTR consist of two files:
- Model XML (``xxx.model.xml``) - Contains general information about
the module's input and output ports and their relations.
- Physical Block XML (``xxx.pb_type.xml``) - Describes the actual layout of the
primitive, with information about the timings, internal connections, etc.
Below you can see the pb_type XML for ``BUFGCTRL_VPR`` primitive:
.. code-block:: xml
<!-- Model of BUFG group in BUFG_CLK_TOP/BOT -->
<pb_type name="BLK-TL-BUFGCTRL" xmlns:xi="http://www.w3.org/2001/XInclude">
<output name="O" num_pins="1"/>
<input name="CE0" num_pins="1"/>
<input name="CE1" num_pins="1"/>
<clock name="I0" num_pins="1"/>
<clock name="I1" num_pins="1"/>
<input name="IGNORE0" num_pins="1"/>
<input name="IGNORE1" num_pins="1"/>
<input name="S0" num_pins="1"/>
<input name="S1" num_pins="1"/>
<mode name="EMPTY">
<pb_type name="empty" blif_model=".latch" num_pb="1" />
<interconnect />
</mode>
<mode name="BUFGCTRL">
<pb_type name="BUFGCTRL_VPR" blif_model=".subckt BUFGCTRL_VPR" num_pb="1">
<output name="O" num_pins="1"/>
<input name="CE0" num_pins="1"/>
<input name="CE1" num_pins="1"/>
<clock name="I0" num_pins="1"/>
<clock name="I1" num_pins="1"/>
<input name="IGNORE0" num_pins="1"/>
<input name="IGNORE1" num_pins="1"/>
<input name="S0" num_pins="1"/>
<input name="S1" num_pins="1"/>
<metadata>
<meta name="fasm_params">
ZPRESELECT_I0 = ZPRESELECT_I0
ZPRESELECT_I1 = ZPRESELECT_I1
IS_IGNORE0_INVERTED = IS_IGNORE0_INVERTED
IS_IGNORE1_INVERTED = IS_IGNORE1_INVERTED
ZINV_CE0 = ZINV_CE0
ZINV_CE1 = ZINV_CE1
ZINV_S0 = ZINV_S0
ZINV_S1 = ZINV_S1
</meta>
</metadata>
</pb_type>
<interconnect>
<direct name="O" input="BUFGCTRL_VPR.O" output="BLK-TL-BUFGCTRL.O"/>
<direct name="CE0" input="BLK-TL-BUFGCTRL.CE0" output="BUFGCTRL_VPR.CE0"/>
<direct name="CE1" input="BLK-TL-BUFGCTRL.CE1" output="BUFGCTRL_VPR.CE1"/>
<direct name="I0" input="BLK-TL-BUFGCTRL.I0" output="BUFGCTRL_VPR.I0"/>
<direct name="I1" input="BLK-TL-BUFGCTRL.I1" output="BUFGCTRL_VPR.I1"/>
<direct name="IGNORE0" input="BLK-TL-BUFGCTRL.IGNORE0" output="BUFGCTRL_VPR.IGNORE0"/>
<direct name="IGNORE1" input="BLK-TL-BUFGCTRL.IGNORE1" output="BUFGCTRL_VPR.IGNORE1"/>
<direct name="S0" input="BLK-TL-BUFGCTRL.S0" output="BUFGCTRL_VPR.S0"/>
<direct name="S1" input="BLK-TL-BUFGCTRL.S1" output="BUFGCTRL_VPR.S1"/>
</interconnect>
<metadata>
<meta name="fasm_features">
IN_USE
</meta>
</metadata>
</mode>
</pb_type>
A correctly prepared techmap for any VPR model contains a declaration of
the module that should be substituted. Inside the module declaration, one
should provide a necessary logic and instantiate another module that
will substitute its original version. Additionally, all equations within
a techmap that are not used directly in a module instantiation should evaluate
to a constant value. Therefore most of the techmaps use additional constant
parameters to modify the signals attached to the instantiated module.
Here is a piece of a techmap, which instructs Yosys to convert
a ``BUFG`` primitive to the ``BUFGCTRL_VPR``. In this case, the techmaping process
consists of two steps. Firstly, the techmap shows how to translate the ``BUFG``
primitive to the ``BUFGCTRL``. Then how to translate the ``BUFGCTRL`` to
the ``BUFGCTRL_VPR``:
.. code-block:: verilog
module BUFG (
input I,
output O
);
BUFGCTRL _TECHMAP_REPLACE_ (
.O(O),
.CE0(1'b1),
.CE1(1'b0),
.I0(I),
.I1(1'b1),
.IGNORE0(1'b0),
.IGNORE1(1'b1),
.S0(1'b1),
.S1(1'b0)
);
endmodule
module BUFGCTRL (
output O,
input I0, input I1,
input S0, input S1,
input CE0, input CE1,
input IGNORE0, input IGNORE1
);
parameter [0:0] INIT_OUT = 1'b0;
parameter [0:0] PRESELECT_I0 = 1'b0;
parameter [0:0] PRESELECT_I1 = 1'b0;
parameter [0:0] IS_IGNORE0_INVERTED = 1'b0;
parameter [0:0] IS_IGNORE1_INVERTED = 1'b0;
parameter [0:0] IS_CE0_INVERTED = 1'b0;
parameter [0:0] IS_CE1_INVERTED = 1'b0;
parameter [0:0] IS_S0_INVERTED = 1'b0;
parameter [0:0] IS_S1_INVERTED = 1'b0;
parameter _TECHMAP_CONSTMSK_IGNORE0_ = 0;
parameter _TECHMAP_CONSTVAL_IGNORE0_ = 0;
parameter _TECHMAP_CONSTMSK_IGNORE1_ = 0;
parameter _TECHMAP_CONSTVAL_IGNORE1_ = 0;
parameter _TECHMAP_CONSTMSK_CE0_ = 0;
parameter _TECHMAP_CONSTVAL_CE0_ = 0;
parameter _TECHMAP_CONSTMSK_CE1_ = 0;
parameter _TECHMAP_CONSTVAL_CE1_ = 0;
parameter _TECHMAP_CONSTMSK_S0_ = 0;
parameter _TECHMAP_CONSTVAL_S0_ = 0;
parameter _TECHMAP_CONSTMSK_S1_ = 0;
parameter _TECHMAP_CONSTVAL_S1_ = 0;
localparam [0:0] INV_IGNORE0 = (
_TECHMAP_CONSTMSK_IGNORE0_ == 1 &&
_TECHMAP_CONSTVAL_IGNORE0_ == 0 &&
IS_IGNORE0_INVERTED == 0);
localparam [0:0] INV_IGNORE1 = (
_TECHMAP_CONSTMSK_IGNORE1_ == 1 &&
_TECHMAP_CONSTVAL_IGNORE1_ == 0 &&
IS_IGNORE1_INVERTED == 0);
localparam [0:0] INV_CE0 = (
_TECHMAP_CONSTMSK_CE0_ == 1 &&
_TECHMAP_CONSTVAL_CE0_ == 0 &&
IS_CE0_INVERTED == 0);
localparam [0:0] INV_CE1 = (
_TECHMAP_CONSTMSK_CE1_ == 1 &&
_TECHMAP_CONSTVAL_CE1_ == 0 &&
IS_CE1_INVERTED == 0);
localparam [0:0] INV_S0 = (
_TECHMAP_CONSTMSK_S0_ == 1 &&
_TECHMAP_CONSTVAL_S0_ == 0 &&
IS_S0_INVERTED == 0);
localparam [0:0] INV_S1 = (
_TECHMAP_CONSTMSK_S1_ == 1 &&
_TECHMAP_CONSTVAL_S1_ == 0 &&
IS_S1_INVERTED == 0);
BUFGCTRL_VPR #(
.INIT_OUT(INIT_OUT),
.ZPRESELECT_I0(PRESELECT_I0),
.ZPRESELECT_I1(PRESELECT_I1),
.IS_IGNORE0_INVERTED(!IS_IGNORE0_INVERTED ^ INV_IGNORE0),
.IS_IGNORE1_INVERTED(!IS_IGNORE1_INVERTED ^ INV_IGNORE1),
.ZINV_CE0(!IS_CE0_INVERTED ^ INV_CE0),
.ZINV_CE1(!IS_CE1_INVERTED ^ INV_CE1),
.ZINV_S0(!IS_S0_INVERTED ^ INV_S0),
.ZINV_S1(!IS_S1_INVERTED ^ INV_S1)
) _TECHMAP_REPLACE_ (
.O(O),
.CE0(CE0 ^ INV_CE0),
.CE1(CE1 ^ INV_CE1),
.I0(I0),
.I1(I1),
.IGNORE0(IGNORE0 ^ INV_IGNORE0),
.IGNORE1(IGNORE1 ^ INV_IGNORE1),
.S0(S0 ^ INV_S0),
.S1(S1 ^ INV_S1)
);
endmodule
.. note::
All SymbiFlow techmaps for Xilinx 7-Series devices use special inverter
logic that converts constant 0 signals at the BEL to constant-1 signals
at the site. This behavior is desired since VCC is the default signal in
7-Series and US/US+ devices. The presented solution matches the conventions
used by the vendor tools and gives the opportunity to validate generated
bitstreams with fasm2bels and Vivado.
Yosys provides special techmapping naming conventions for wires,
parameters, and modules. The special names that start with ``_TECHMAP_``
can be used to force certain behavior during the techmapping process.
Currently, the following special names are used in SymbiFlow techmaps:
- ``_TECHMAP_REPLACE_`` is used as a name for an instantiated module, which will
replace the one used in the original design. This special name causes
the instantiated module to inherit the name and all attributes
from the module that is being replaced.
- ``_TECHMAP_CONSTMSK_<port_name>_`` and ``_TECHMAP_CONSTVAL_<port_name>_``
are used together as names of parameters. The ``_TECHMAP_CONSTMASK_<port_name>_``
has a length of the input signal. Its bits take the value 1 if
the corresponding signal bit has a constant value, or 0 otherwise.
The ``_TECHMAP_CONSTVAL_<port_name>_`` bits store the actual constant signal
values when the ``_TECHMAP_CONSTMASK_<port_name>_`` is equal to 1.
More information about special wire, parameter, and module names can be found in
`techmap section in the Yosys Manual`_.
.. note::
Techmapping can be used not only to change the names of the primitives
but primarily to match the port declarations and express the logic behind
the primitive substitution:
.. verilog:module:: module BUFG (output O, input I)
.. verilog:module:: module BUFGCTRL (output O, input CE0, input CE1, input I0, input I1, input IGNORE0, input IGNORE1, input S0, input S1)
More information
----------------
Additional information about Yosys can be found on the `Yosys Project Website
<http://www.clifford.at/yosys/>`_ , or in `Yosys Manual
<http://www.clifford.at/yosys/files/yosys_manual.pdf>`_. You can also compile
one of the tests described in Getting Started section and watch the log file
to understand which operations are performed by Yosys.