692 lines
53 KiB
Plaintext
692 lines
53 KiB
Plaintext
|
/****************************************************************************************
|
||
|
|
*
|
||
|
|
* Disclaimer This software code and all associated documentation, comments or other
|
||
|
|
* of Warranty: information (collectively "Software") is provided "AS IS" without
|
||
|
|
* warranty of any kind. MICRON TECHNOLOGY, INC. ("MTI") EXPRESSLY
|
||
|
|
* DISCLAIMS ALL WARRANTIES EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
|
||
|
|
* TO, NONINFRINGEMENT OF THIRD PARTY RIGHTS, AND ANY IMPLIED WARRANTIES
|
||
|
|
* OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. MTI DOES NOT
|
||
|
|
* WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT THE
|
||
|
|
* OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
|
||
|
|
* FURTHERMORE, MTI DOES NOT MAKE ANY REPRESENTATIONS REGARDING THE USE OR
|
||
|
|
* THE RESULTS OF THE USE OF THE SOFTWARE IN TERMS OF ITS CORRECTNESS,
|
||
|
|
* ACCURACY, RELIABILITY, OR OTHERWISE. THE ENTIRE RISK ARISING OUT OF USE
|
||
|
|
* OR PERFORMANCE OF THE SOFTWARE REMAINS WITH YOU. IN NO EVENT SHALL MTI,
|
||
|
|
* ITS AFFILIATED COMPANIES OR THEIR SUPPLIERS BE LIABLE FOR ANY DIRECT,
|
||
|
|
* INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES (INCLUDING,
|
||
|
|
* WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION,
|
||
|
|
* OR LOSS OF INFORMATION) ARISING OUT OF YOUR USE OF OR INABILITY TO USE
|
||
|
|
* THE SOFTWARE, EVEN IF MTI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
|
||
|
|
* DAMAGES. Because some jurisdictions prohibit the exclusion or
|
||
|
|
* limitation of liability for consequential or incidental damages, the
|
||
|
|
* above limitation may not apply to you.
|
||
|
|
*
|
||
|
|
* Copyright 2003 Micron Technology, Inc. All rights reserved.
|
||
|
|
*
|
||
|
|
****************************************************************************************/
|
||
|
|
|
||
|
|
// Timing parameters based on 2Gb_DDR3_SDRAM.pdf - Rev. P 2/12 EN
|
||
|
|
|
||
|
|
// SYMBOL UNITS DESCRIPTION
|
||
|
|
// ------ ----- -----------
|
||
|
|
`ifdef sg093 // sg093 is equivalent to the JEDEC DDR3-2133 (14-14-14) speed bin
|
||
|
|
parameter TCK_MIN = 938; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 50; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 100; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 74; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 87; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 97; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 105; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 111; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 116; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 121; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 125; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 128; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 132; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 134; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 5; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 20; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 70; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.27; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.18; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.18; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 180; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.40; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.40; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 280; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 470; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 35; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 75; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 33000; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 46130; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 13090; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 13090; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 6000; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5000; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 180; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 122; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 122; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 7500; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 13090; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 13090; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg107 // sg107 is equivalent to the JEDEC DDR3-1866 (13-13-13) speed bin
|
||
|
|
parameter TCK_MIN = 1071; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 60; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 120; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 88; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 105; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 117; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 126; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 133; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 139; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 145; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 150; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 154; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 158; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 161; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 10; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 20; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 80; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.27; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.18; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.18; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 200; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.40; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.40; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 320; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 535; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 50; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 100; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 34000; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 48910; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 13910; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 13910; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 6000; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5000; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 200; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 140; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 140; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 7500; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 13910; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 13910; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg125 // sg125 is equivalent to the JEDEC DDR3-1600 (11-11-11) speed bin
|
||
|
|
parameter TCK_MIN = 1250; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 70; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 140; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 103; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 122; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 136; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 147; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 155; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 163; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 169; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 175; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 180; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 184; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 188; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 10; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 45; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 100; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.27; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.18; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.18; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 225; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.40; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.40; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 360; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 560; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 170; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 120; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 35000; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 48750; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 13750; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 13750; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 6000; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5000; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 250; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 165; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 165; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 7500; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 13750; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 13750; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg15E // sg15E is equivalent to the JEDEC DDR3-1333H (9-9-9) speed bin
|
||
|
|
parameter TCK_MIN = 1500; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 80; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 160; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 118; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 140; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 155; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 168; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 177; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 186; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 193; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 200; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 205; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 210; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 215; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 30; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 65; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 125; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 255; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.40; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.40; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 400; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 620; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 190; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 140; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 36000; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 49500; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 13500; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 13500; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 6000; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5625; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 250; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 195; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 195; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 13500; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 13500; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg15 // sg15 is equivalent to the JEDEC DDR3-1333J (10-10-10) speed bin
|
||
|
|
parameter TCK_MIN = 1500; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 80; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 160; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 118; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 140; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 155; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 168; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 177; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 186; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 193; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 200; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 205; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 210; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 215; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 30; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 65; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 125; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 255; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.40; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.40; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 400; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 620; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 190; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 140; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 36000; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 51000; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 15000; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 15000; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 6000; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5625; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 250; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 195; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 195; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 15000; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 15000; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg187E // sg187E is equivalent to the JEDEC DDR3-1066F (7-7-7) speed bin
|
||
|
|
parameter TCK_MIN = 1875; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 90; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 180; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 132; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 157; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 175; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 188; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 200; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 209; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 217; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 224; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 231; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 237; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 242; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 75; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 100; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 150; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 300; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.38; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.38; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 490; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 780; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 275; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 200; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 37500; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 50625; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 13125; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 13125; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 7500; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5625; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 300; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 245; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 245; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 13125; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 13125; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg187 // sg187 is equivalent to the JEDEC DDR3-1066G (8-8-8) speed bin
|
||
|
|
parameter TCK_MIN = 1875; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 90; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 180; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 132; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 157; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 175; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 188; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 200; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 209; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 217; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 224; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 231; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 237; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 242; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 75; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 100; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 150; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 300; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.38; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.38; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 490; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 780; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 275; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 200; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 37500; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 52500; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 15000; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 15000; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 7500; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 5625; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 300; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 245; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 245; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 15000; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 15000; // CL ps Minimum CAS Latency
|
||
|
|
`elsif sg25E // sg25E is equivalent to the JEDEC DDR3-800D (5-5-5) speed bin
|
||
|
|
parameter TCK_MIN = 2500; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 100; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 200; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 147; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 175; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 194; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 209; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 222; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 232; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 241; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 249; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 257; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 263; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 269; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 125; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 150; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 200; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 400; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.38; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.38; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 600; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 900; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 350; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 275; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 37500; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 50000; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 12500; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 12500; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 7500; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 7500; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 400; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 325; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 325; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 12500; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 12500; // CL ps Minimum CAS Latency
|
||
|
|
`else
|
||
|
|
`define sg25 // sg25 is equivalent to the JEDEC DDR3-800E (6-6-6) speed bin
|
||
|
|
parameter TCK_MIN = 2500; // tCK ps Minimum Clock Cycle Time
|
||
|
|
parameter TJIT_PER = 100; // tJIT(per) ps Period JItter
|
||
|
|
parameter TJIT_CC = 200; // tJIT(cc) ps Cycle to Cycle jitter
|
||
|
|
parameter TERR_2PER = 147; // tERR(2per) ps Accumulated Error (2-cycle)
|
||
|
|
parameter TERR_3PER = 175; // tERR(3per) ps Accumulated Error (3-cycle)
|
||
|
|
parameter TERR_4PER = 194; // tERR(4per) ps Accumulated Error (4-cycle)
|
||
|
|
parameter TERR_5PER = 209; // tERR(5per) ps Accumulated Error (5-cycle)
|
||
|
|
parameter TERR_6PER = 222; // tERR(6per) ps Accumulated Error (6-cycle)
|
||
|
|
parameter TERR_7PER = 232; // tERR(7per) ps Accumulated Error (7-cycle)
|
||
|
|
parameter TERR_8PER = 241; // tERR(8per) ps Accumulated Error (8-cycle)
|
||
|
|
parameter TERR_9PER = 249; // tERR(9per) ps Accumulated Error (9-cycle)
|
||
|
|
parameter TERR_10PER = 257; // tERR(10per)ps Accumulated Error (10-cycle)
|
||
|
|
parameter TERR_11PER = 263; // tERR(11per)ps Accumulated Error (11-cycle)
|
||
|
|
parameter TERR_12PER = 269; // tERR(12per)ps Accumulated Error (12-cycle)
|
||
|
|
parameter TDS = 125; // tDS ps DQ and DM input setup time relative to DQS
|
||
|
|
parameter TDH = 150; // tDH ps DQ and DM input hold time relative to DQS
|
||
|
|
parameter TDQSQ = 200; // tDQSQ ps DQS-DQ skew, DQS to last DQ valid, per group, per access
|
||
|
|
parameter TDQSS = 0.25; // tDQSS tCK Rising clock edge to DQS/DQS# latching transition
|
||
|
|
parameter TDSS = 0.20; // tDSS tCK DQS falling edge to CLK rising (setup time)
|
||
|
|
parameter TDSH = 0.20; // tDSH tCK DQS falling edge from CLK rising (hold time)
|
||
|
|
parameter TDQSCK = 400; // tDQSCK ps DQS output access time from CK/CK#
|
||
|
|
parameter TQSH = 0.38; // tQSH tCK DQS Output High Pulse Width
|
||
|
|
parameter TQSL = 0.38; // tQSL tCK DQS Output Low Pulse Width
|
||
|
|
parameter TDIPW = 600; // tDIPW ps DQ and DM input Pulse Width
|
||
|
|
parameter TIPW = 900; // tIPW ps Control and Address input Pulse Width
|
||
|
|
parameter TIS = 350; // tIS ps Input Setup Time
|
||
|
|
parameter TIH = 275; // tIH ps Input Hold Time
|
||
|
|
parameter TRAS_MIN = 37500; // tRAS ps Minimum Active to Precharge command time
|
||
|
|
parameter TRC = 52500; // tRC ps Active to Active/Auto Refresh command time
|
||
|
|
parameter TRCD = 15000; // tRCD ps Active to Read/Write command time
|
||
|
|
parameter TRP = 15000; // tRP ps Precharge command period
|
||
|
|
parameter TXP = 7500; // tXP ps Exit power down to a valid command
|
||
|
|
parameter TCKE = 7500; // tCKE ps CKE minimum high or low pulse width
|
||
|
|
parameter TAON = 400; // tAON ps RTT turn-on from ODTLon reference
|
||
|
|
parameter TWLS = 325; // tWLS ps Setup time for tDQS flop
|
||
|
|
parameter TWLH = 325; // tWLH ps Hold time of tDQS flop
|
||
|
|
parameter TWLO = 9000; // tWLO ps Write levelization output delay
|
||
|
|
parameter TAA_MIN = 15000; // TAA ps Internal READ command to first data
|
||
|
|
parameter CL_TIME = 15000; // CL ps Minimum CAS Latency
|
||
|
|
`endif
|
||
|
|
|
||
|
|
parameter TDQSCK_DLLDIS = TDQSCK; // tDQSCK ps for DLLDIS mode, timing not guaranteed
|
||
|
|
|
||
|
|
`ifdef x16
|
||
|
|
`ifdef sg093
|
||
|
|
parameter TRRD = 6000; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 35000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`elsif sg107
|
||
|
|
parameter TRRD = 6000; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 35000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`elsif sg125
|
||
|
|
parameter TRRD = 7500; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 40000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`elsif sg15E
|
||
|
|
parameter TRRD = 7500; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 45000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`elsif sg15
|
||
|
|
parameter TRRD = 7500; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 45000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`else // sg187E, sg187, sg25, sg25E
|
||
|
|
parameter TRRD = 10000; // tRRD ps (2KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 50000; // tFAW ps (2KB page size) Four Bank Activate window
|
||
|
|
`endif
|
||
|
|
`else // x4, x8
|
||
|
|
`ifdef sg093
|
||
|
|
parameter TRRD = 5000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 25000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg107
|
||
|
|
parameter TRRD = 5000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 25000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg125
|
||
|
|
parameter TRRD = 6000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 30000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg15E
|
||
|
|
parameter TRRD = 6000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 30000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg15
|
||
|
|
parameter TRRD = 6000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 30000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg187E
|
||
|
|
parameter TRRD = 7500; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 37500; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`elsif sg187
|
||
|
|
parameter TRRD = 7500; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 37500; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`else // sg25, sg25E
|
||
|
|
parameter TRRD = 10000; // tRRD ps (1KB page size) Active bank a to Active bank b command time
|
||
|
|
parameter TFAW = 40000; // tFAW ps (1KB page size) Four Bank Activate window
|
||
|
|
`endif
|
||
|
|
`endif
|
||
|
|
|
||
|
|
// Timing Parameters
|
||
|
|
|
||
|
|
// Mode Register
|
||
|
|
parameter CL_MIN = 5; // CL tCK Minimum CAS Latency
|
||
|
|
parameter CL_MAX = 14; // CL tCK Maximum CAS Latency
|
||
|
|
parameter AL_MIN = 0; // AL tCK Minimum Additive Latency
|
||
|
|
parameter AL_MAX = 2; // AL tCK Maximum Additive Latency
|
||
|
|
parameter WR_MIN = 5; // WR tCK Minimum Write Recovery
|
||
|
|
parameter WR_MAX = 16; // WR tCK Maximum Write Recovery
|
||
|
|
parameter BL_MIN = 4; // BL tCK Minimum Burst Length
|
||
|
|
parameter BL_MAX = 8; // BL tCK Minimum Burst Length
|
||
|
|
parameter CWL_MIN = 5; // CWL tCK Minimum CAS Write Latency
|
||
|
|
parameter CWL_MAX = 10; // CWL tCK Maximum CAS Write Latency
|
||
|
|
|
||
|
|
// Clock
|
||
|
|
parameter TCK_MAX = 3300; // tCK ps Maximum Clock Cycle Time
|
||
|
|
parameter TCH_AVG_MIN = 0.47; // tCH tCK Minimum Clock High-Level Pulse Width
|
||
|
|
parameter TCL_AVG_MIN = 0.47; // tCL tCK Minimum Clock Low-Level Pulse Width
|
||
|
|
parameter TCH_AVG_MAX = 0.53; // tCH tCK Maximum Clock High-Level Pulse Width
|
||
|
|
parameter TCL_AVG_MAX = 0.53; // tCL tCK Maximum Clock Low-Level Pulse Width
|
||
|
|
parameter TCH_ABS_MIN = 0.43; // tCH tCK Minimum Clock High-Level Pulse Width
|
||
|
|
parameter TCL_ABS_MIN = 0.43; // tCL tCK Maximum Clock Low-Level Pulse Width
|
||
|
|
parameter TCKE_TCK = 3; // tCKE tCK CKE minimum high or low pulse width
|
||
|
|
parameter TAA_MAX = 20000; // TAA ps Internal READ command to first data
|
||
|
|
|
||
|
|
// Data OUT
|
||
|
|
parameter TQH = 0.38; // tQH ps DQ output hold time from DQS, DQS#
|
||
|
|
// Data Strobe OUT
|
||
|
|
parameter TRPRE = 0.90; // tRPRE tCK DQS Read Preamble
|
||
|
|
parameter TRPST = 0.30; // tRPST tCK DQS Read Postamble
|
||
|
|
// Data Strobe IN
|
||
|
|
parameter TDQSH = 0.45; // tDQSH tCK DQS input High Pulse Width
|
||
|
|
parameter TDQSL = 0.45; // tDQSL tCK DQS input Low Pulse Width
|
||
|
|
parameter TWPRE = 0.90; // tWPRE tCK DQS Write Preamble
|
||
|
|
parameter TWPST = 0.30; // tWPST tCK DQS Write Postamble
|
||
|
|
// Command and Address
|
||
|
|
integer TZQCS; // tZQCS tCK ZQ Cal (Short) time
|
||
|
|
integer TZQINIT; // tZQinit tCK ZQ Cal (Long) time
|
||
|
|
integer TZQOPER; // tZQoper tCK ZQ Cal (Long) time
|
||
|
|
parameter TCCD = 4; // tCCD tCK Cas to Cas command delay
|
||
|
|
parameter TCCD_DG = 2; // tCCD_DG tCK Cas to Cas command delay to different group
|
||
|
|
parameter TRAS_MAX = 60e9; // tRAS ps Maximum Active to Precharge command time
|
||
|
|
parameter TWR = 15000; // tWR ps Write recovery time
|
||
|
|
parameter TMRD = 4; // tMRD tCK Load Mode Register command cycle time
|
||
|
|
parameter TMOD = 15000; // tMOD ps LOAD MODE to non-LOAD MODE command cycle time
|
||
|
|
parameter TMOD_TCK = 12; // tMOD tCK LOAD MODE to non-LOAD MODE command cycle time
|
||
|
|
parameter TRRD_TCK = 4; // tRRD tCK Active bank a to Active bank b command time
|
||
|
|
parameter TRRD_DG = 3000; // tRRD_DG ps Active bank a to Active bank b command time to different group
|
||
|
|
parameter TRRD_DG_TCK = 2; // tRRD_DG tCK Active bank a to Active bank b command time to different group
|
||
|
|
parameter TRTP = 7500; // tRTP ps Read to Precharge command delay
|
||
|
|
parameter TRTP_TCK = 4; // tRTP tCK Read to Precharge command delay
|
||
|
|
parameter TWTR = 7500; // tWTR ps Write to Read command delay
|
||
|
|
parameter TWTR_DG = 3750; // tWTR_DG ps Write to Read command delay to different group
|
||
|
|
parameter TWTR_TCK = 4; // tWTR tCK Write to Read command delay
|
||
|
|
parameter TWTR_DG_TCK = 2; // tWTR_DG tCK Write to Read command delay to different group
|
||
|
|
parameter TDLLK = 512; // tDLLK tCK DLL locking time
|
||
|
|
// Refresh - 2Gb
|
||
|
|
parameter TRFC_MIN = 160000; // tRFC ps Refresh to Refresh Command interval minimum value
|
||
|
|
parameter TRFC_MAX =70200000; // tRFC ps Refresh to Refresh Command Interval maximum value
|
||
|
|
// Power Down
|
||
|
|
parameter TXP_TCK = 3; // tXP tCK Exit power down to a valid command
|
||
|
|
parameter TXPDLL = 24000; // tXPDLL ps Exit precharge power down to READ or WRITE command (DLL-off mode)
|
||
|
|
parameter TXPDLL_TCK = 10; // tXPDLL tCK Exit precharge power down to READ or WRITE command (DLL-off mode)
|
||
|
|
parameter TACTPDEN = 1; // tACTPDEN tCK Timing of last ACT command to power down entry
|
||
|
|
parameter TPRPDEN = 1; // tPREPDEN tCK Timing of last PRE command to power down entry
|
||
|
|
parameter TREFPDEN = 1; // tARPDEN tCK Timing of last REFRESH command to power down entry
|
||
|
|
parameter TCPDED = 1; // tCPDED tCK Command pass disable/enable delay
|
||
|
|
parameter TPD_MAX =TRFC_MAX; // tPD ps Power-down entry-to-exit timing
|
||
|
|
parameter TXPR = 170000; // tXPR ps Exit Reset from CKE assertion to a valid command
|
||
|
|
parameter TXPR_TCK = 5; // tXPR tCK Exit Reset from CKE assertion to a valid command
|
||
|
|
// Self Refresh
|
||
|
|
parameter TXS = 170000; // tXS ps Exit self refesh to a non-read or write command
|
||
|
|
parameter TXS_TCK = 5; // tXS tCK Exit self refesh to a non-read or write command
|
||
|
|
parameter TXSDLL = TDLLK; // tXSRD tCK Exit self refresh to a read or write command
|
||
|
|
parameter TISXR = TIS; // tISXR ps CKE setup time during self refresh exit.
|
||
|
|
parameter TCKSRE = 10000; // tCKSRE ps Valid Clock requirement after self refresh entry (SRE)
|
||
|
|
parameter TCKSRE_TCK = 5; // tCKSRE tCK Valid Clock requirement after self refresh entry (SRE)
|
||
|
|
parameter TCKSRX = 10000; // tCKSRX ps Valid Clock requirement prior to self refresh exit (SRX)
|
||
|
|
parameter TCKSRX_TCK = 5; // tCKSRX tCK Valid Clock requirement prior to self refresh exit (SRX)
|
||
|
|
parameter TCKESR_TCK = 4; // tCKESR tCK Minimum CKE low width for Self Refresh entry to exit timing
|
||
|
|
// ODT
|
||
|
|
parameter TAOF = 0.7; // tAOF tCK RTT turn-off from ODTLoff reference
|
||
|
|
parameter TAONPD = 8500; // tAONPD ps Asynchronous RTT turn-on delay (Power-Down with DLL frozen)
|
||
|
|
parameter TAOFPD = 8500; // tAONPD ps Asynchronous RTT turn-off delay (Power-Down with DLL frozen)
|
||
|
|
parameter ODTH4 = 4; // ODTH4 tCK ODT minimum HIGH time after ODT assertion or write (BL4)
|
||
|
|
parameter ODTH8 = 6; // ODTH8 tCK ODT minimum HIGH time after write (BL8)
|
||
|
|
parameter TADC = 0.7; // tADC tCK RTT dynamic change skew
|
||
|
|
// Write Levelization
|
||
|
|
parameter TWLMRD = 40; // tWLMRD tCK First DQS pulse rising edge after tDQSS margining mode is programmed
|
||
|
|
parameter TWLDQSEN = 25; // tWLDQSEN tCK DQS/DQS delay after tDQSS margining mode is programmed
|
||
|
|
parameter TWLOE = 2000; // tWLOE ps Write levelization output error
|
||
|
|
|
||
|
|
// Size Parameters based on Part Width
|
||
|
|
|
||
|
|
`ifdef x4
|
||
|
|
parameter DM_BITS = 1; // Set this parameter to control how many Data Mask bits are used
|
||
|
|
parameter ADDR_BITS = 15; // MAX Address Bits
|
||
|
|
parameter ROW_BITS = 15; // Set this parameter to control how many Address bits are used
|
||
|
|
parameter COL_BITS = 11; // Set this parameter to control how many Column bits are used
|
||
|
|
parameter DQ_BITS = 4; // Set this parameter to control how many Data bits are used **Same as part bit width**
|
||
|
|
parameter DQS_BITS = 1; // Set this parameter to control how many Dqs bits are used
|
||
|
|
`elsif x8
|
||
|
|
parameter DM_BITS = 1; // Set this parameter to control how many Data Mask bits are used
|
||
|
|
parameter ADDR_BITS = 15; // MAX Address Bits
|
||
|
|
parameter ROW_BITS = 15; // Set this parameter to control how many Address bits are used
|
||
|
|
parameter COL_BITS = 10; // Set this parameter to control how many Column bits are used
|
||
|
|
parameter DQ_BITS = 8; // Set this parameter to control how many Data bits are used **Same as part bit width**
|
||
|
|
parameter DQS_BITS = 1; // Set this parameter to control how many Dqs bits are used
|
||
|
|
`else
|
||
|
|
`define x16
|
||
|
|
parameter DM_BITS = 2; // Set this parameter to control how many Data Mask bits are used
|
||
|
|
parameter ADDR_BITS = 14; // MAX Address Bits
|
||
|
|
parameter ROW_BITS = 14; // Set this parameter to control how many Address bits are used
|
||
|
|
parameter COL_BITS = 10; // Set this parameter to control how many Column bits are used
|
||
|
|
parameter DQ_BITS = 16; // Set this parameter to control how many Data bits are used **Same as part bit width**
|
||
|
|
parameter DQS_BITS = 2; // Set this parameter to control how many Dqs bits are used
|
||
|
|
`endif
|
||
|
|
|
||
|
|
// Size Parameters
|
||
|
|
parameter BA_BITS = 3; // Set this parmaeter to control how many Bank Address bits are used
|
||
|
|
parameter MEM_BITS = 10; // Set this parameter to control how many write data bursts can be stored in memory. The default is 2^10=1024.
|
||
|
|
parameter AP = 10; // the address bit that controls auto-precharge and precharge-all
|
||
|
|
parameter BC = 12; // the address bit that controls burst chop
|
||
|
|
parameter BL_BITS = 3; // the number of bits required to count to BL_MAX
|
||
|
|
parameter BO_BITS = 2; // the number of Burst Order Bits
|
||
|
|
|
||
|
|
`ifdef QUAD_RANK
|
||
|
|
parameter CS_BITS = 4; // Number of Chip Select Bits
|
||
|
|
parameter RANKS = 4; // Number of Chip Selects
|
||
|
|
`elsif DUAL_RANK
|
||
|
|
parameter CS_BITS = 2; // Number of Chip Select Bits
|
||
|
|
parameter RANKS = 2; // Number of Chip Selects
|
||
|
|
`else
|
||
|
|
parameter CS_BITS = 1; // Number of Chip Select Bits
|
||
|
|
parameter RANKS = 1; // Number of Chip Selects
|
||
|
|
`endif
|
||
|
|
|
||
|
|
// Simulation parameters
|
||
|
|
parameter RZQ = 240; // termination resistance
|
||
|
|
parameter PRE_DEF_PAT = 8'hAA; // value returned during mpr pre-defined pattern readout
|
||
|
|
parameter STOP_ON_ERROR = 1; // If set to 1, the model will halt on command sequence/major errors
|
||
|
|
parameter DEBUG = 1; // Turn on Debug messages
|
||
|
|
parameter BUS_DELAY = 0; // delay in nanoseconds
|
||
|
|
parameter RANDOM_OUT_DELAY = 0; // If set to 1, the model will put a random amount of delay on DQ/DQS during reads
|
||
|
|
parameter RANDOM_SEED = 31913; //seed value for random generator.
|
||
|
|
|
||
|
|
parameter RDQSEN_PRE = 2; // DQS driving time prior to first read strobe
|
||
|
|
parameter RDQSEN_PST = 1; // DQS driving time after last read strobe
|
||
|
|
parameter RDQS_PRE = 2; // DQS low time prior to first read strobe
|
||
|
|
parameter RDQS_PST = 1; // DQS low time after last read strobe
|
||
|
|
parameter RDQEN_PRE = 0; // DQ/DM driving time prior to first read data
|
||
|
|
parameter RDQEN_PST = 0; // DQ/DM driving time after last read data
|
||
|
|
parameter WDQS_PRE = 2; // DQS half clock periods prior to first write strobe
|
||
|
|
parameter WDQS_PST = 1; // DQS half clock periods after last write strobe
|
||
|
|
|
||
|
|
// check for legal cas latency based on the cas write latency
|
||
|
|
function valid_cl;
|
||
|
|
input [3:0] cl;
|
||
|
|
input [3:0] cwl;
|
||
|
|
|
||
|
|
case ({cwl, cl})
|
||
|
|
`ifdef sg093
|
||
|
|
{4'd5 , 4'd5 },
|
||
|
|
{4'd5 , 4'd6 },
|
||
|
|
{4'd6 , 4'd7 },
|
||
|
|
{4'd6 , 4'd8 },
|
||
|
|
{4'd7 , 4'd9 },
|
||
|
|
{4'd7 , 4'd10},
|
||
|
|
{4'd8 , 4'd11},
|
||
|
|
{4'd9 , 4'd13},
|
||
|
|
{4'd10, 4'd14}: valid_cl = 1;
|
||
|
|
`elsif sg107
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd7 },
|
||
|
|
{4'd6, 4'd8 },
|
||
|
|
{4'd7, 4'd9 },
|
||
|
|
{4'd7, 4'd10},
|
||
|
|
{4'd8, 4'd11},
|
||
|
|
{4'd9, 4'd13}: valid_cl = 1;
|
||
|
|
`elsif sg125
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd7 },
|
||
|
|
{4'd6, 4'd8 },
|
||
|
|
{4'd7, 4'd9 },
|
||
|
|
{4'd7, 4'd10},
|
||
|
|
{4'd8, 4'd11}: valid_cl = 1;
|
||
|
|
`elsif sg15E
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd7 },
|
||
|
|
{4'd6, 4'd8 },
|
||
|
|
{4'd7, 4'd9 },
|
||
|
|
{4'd7, 4'd10}: valid_cl = 1;
|
||
|
|
`elsif sg15
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd8 },
|
||
|
|
{4'd7, 4'd10}: valid_cl = 1;
|
||
|
|
`elsif sg187E
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd7 },
|
||
|
|
{4'd6, 4'd8 }: valid_cl = 1;
|
||
|
|
`elsif sg187
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 },
|
||
|
|
{4'd6, 4'd8 }: valid_cl = 1;
|
||
|
|
`elsif sg25E
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 }: valid_cl = 1;
|
||
|
|
`elsif sg25
|
||
|
|
{4'd5, 4'd5 },
|
||
|
|
{4'd5, 4'd6 }: valid_cl = 1;
|
||
|
|
`endif
|
||
|
|
default : valid_cl = 0;
|
||
|
|
endcase
|
||
|
|
endfunction
|
||
|
|
|
||
|
|
// find the minimum valid cas write latency
|
||
|
|
function [3:0] min_cwl;
|
||
|
|
input period;
|
||
|
|
real period;
|
||
|
|
min_cwl = (period >= 2500.0) ? 5:
|
||
|
|
(period >= 1875.0) ? 6:
|
||
|
|
(period >= 1500.0) ? 7:
|
||
|
|
(period >= 1250.0) ? 8:
|
||
|
|
(period >= 1071.0) ? 9:
|
||
|
|
10; // (period >= 938)
|
||
|
|
endfunction
|
||
|
|
|
||
|
|
// find the minimum valid cas latency
|
||
|
|
function [3:0] min_cl;
|
||
|
|
input period;
|
||
|
|
real period;
|
||
|
|
reg [3:0] cwl;
|
||
|
|
reg [3:0] cl;
|
||
|
|
begin
|
||
|
|
cwl = min_cwl(period);
|
||
|
|
for (cl=CL_MAX; cl>=CL_MIN; cl=cl-1) begin
|
||
|
|
if (valid_cl(cl, cwl)) begin
|
||
|
|
min_cl = cl;
|
||
|
|
end
|
||
|
|
end
|
||
|
|
end
|
||
|
|
endfunction
|