litex/misoclib/mem/litesata/phy/k7/trx.py

864 lines
30 KiB
Python

from misoclib.mem.litesata.common import *
def ones(width):
return 2**width-1
class _PulseSynchronizer(PulseSynchronizer):
def __init__(self, i, idomain, o, odomain):
PulseSynchronizer.__init__(self, idomain, odomain)
self.comb += [
self.i.eq(i),
o.eq(self.o)
]
class _RisingEdge(Module):
def __init__(self, i, o):
i_d = Signal()
self.sync += i_d.eq(i)
self.comb += o.eq(i & ~i_d)
class _LowPassFilter(Module):
def __init__(self, i, o, cycles):
i_d = Signal()
self.submodules.timer = WaitTimer(cycles)
self.sync += [
i_d.eq(i),
If(self.timer.done,
o.eq(i_d)
)
]
self.comb += self.timer.wait.eq(i == i_d)
class K7LiteSATAPHYTRX(Module):
def __init__(self, pads, revision):
# Common signals
# control
self.tx_idle = Signal() #i
self.tx_cominit_stb = Signal() #i
self.tx_cominit_ack = Signal() #o
self.tx_comwake_stb = Signal() #i
self.tx_comwake_ack = Signal() #o
self.rx_idle = Signal() #o
self.rx_align = Signal() #i
self.rx_cominit_stb = Signal() #o
self.rx_comwake_stb = Signal() #o
# datapath
self.sink = Sink(phy_description(16))
self.source = Source(phy_description(16))
# K7 specific signals
# Channel - Ref Clock Ports
self.gtrefclk0 = Signal()
# Channel PLL
self.cplllock = Signal()
self.cpllreset = Signal()
# Receive Ports
self.rxuserrdy = Signal()
# Receive Ports - 8b10b Decoder
self.rxcharisk = Signal(2)
# Receive Ports - RX Data Path interface
self.gtrxreset = Signal()
self.rxdata = Signal(16)
self.rxoutclk = Signal()
self.rxusrclk = Signal()
self.rxusrclk2 = Signal()
# Receive Ports - RX Driver,OOB signalling,Coupling and Eq.,CDR
self.rxelecidle = Signal()
# Receive Ports - RX PLL Ports
self.rxresetdone = Signal()
self.rxdlyreset = Signal()
self.rxdlyresetdone = Signal()
# Receive Ports - RX Ports for SATA
self.rxcominitdet = Signal()
self.rxcomwakedet = Signal()
# Transmit Ports
self.txuserrdy = Signal()
# Transmit Ports - 8b10b Encoder Control Ports
self.txcharisk = Signal(2)
# Transmit Ports - TX Data Path interface
self.gttxreset = Signal()
self.txdata = Signal(16)
self.txoutclk = Signal()
self.txusrclk = Signal()
self.txusrclk2 = Signal()
# Transmit Ports - TX PLL Ports
self.txresetdone = Signal()
self.txdlyreset = Signal()
self.txdlyresetdone = Signal()
# Transmit Ports - TX Ports for PCI Express
self.txelecidle = Signal(reset=1)
# Transmit Ports - TX Ports for SATA
self.txcomfinish = Signal()
self.txcominit = Signal()
self.txcomwake = Signal()
# Config at startup
div_config = {
"sata_gen1": 4,
"sata_gen2": 2,
"sata_gen3": 1
}
rxout_div = div_config[revision]
txout_div = div_config[revision]
cdr_config = {
"sata_gen1": 0x0380008BFF40100008,
"sata_gen2": 0x0388008BFF40200008,
"sata_gen3": 0x0380008BFF10200010
}
rxcdr_cfg = cdr_config[revision]
# Specific / Generic signals encoding/decoding
self.comb += [
self.txelecidle.eq(self.tx_idle),
self.tx_cominit_ack.eq(self.tx_cominit_stb & self.txcomfinish),
self.tx_comwake_ack.eq(self.tx_comwake_stb & self.txcomfinish),
self.rx_idle.eq(self.rxelecidle),
self.rx_cominit_stb.eq(self.rxcominitdet),
self.rx_comwake_stb.eq(self.rxcomwakedet),
]
self.submodules += [
_RisingEdge(self.tx_cominit_stb, self.txcominit),
_RisingEdge(self.tx_comwake_stb, self.txcomwake),
]
self.comb += [
self.txcharisk.eq(self.sink.charisk),
self.txdata.eq(self.sink.data),
self.sink.ack.eq(1),
self.source.stb.eq(1),
self.source.charisk.eq(self.rxcharisk),
self.source.data.eq(self.rxdata)
]
# Internals and clock domain crossing
# sys_clk --> sata_tx clk
txuserrdy = Signal()
txelecidle = Signal(reset=1)
txcominit = Signal()
txcomwake = Signal()
txdlyreset = Signal()
txdlyresetdone = Signal()
gttxreset = Signal()
self.specials += [
MultiReg(self.txuserrdy, txuserrdy, "sata_tx"),
MultiReg(self.txelecidle, txelecidle, "sata_tx"),
MultiReg(self.gttxreset, gttxreset, "sata_tx"),
]
self.submodules += [
_PulseSynchronizer(self.txcominit, "sys", txcominit, "sata_tx"),
_PulseSynchronizer(self.txcomwake, "sys", txcomwake, "sata_tx"),
_PulseSynchronizer(self.txdlyreset, "sys", txdlyreset, "sata_tx"),
]
# sata_tx clk --> sys clk
txresetdone = Signal()
txcomfinish = Signal()
self.specials += [
MultiReg(txresetdone, self.txresetdone, "sys"),
MultiReg(txdlyresetdone, self.txdlyresetdone, "sys"),
]
self.submodules += [
_PulseSynchronizer(txcomfinish, "sata_tx", self.txcomfinish, "sys"),
]
# sys clk --> sata_rx clk
rxuserrdy = Signal()
rxdlyreset = Signal()
self.specials += [
MultiReg(self.rxuserrdy, rxuserrdy, "sata_rx"),
]
self.submodules += [
_PulseSynchronizer(self.rxdlyreset, "sys", rxdlyreset, "sata_rx"),
]
# sata_rx clk --> sys clk
rxelecidle = Signal()
rxelecidle_i = Signal()
rxresetdone = Signal()
rxcominitdet = Signal()
rxcomwakedet = Signal()
rxratedone = Signal()
rxdlyresetdone = Signal()
self.specials += [
MultiReg(rxelecidle, rxelecidle_i, "sys"),
MultiReg(rxresetdone, self.rxresetdone, "sys"),
MultiReg(rxcominitdet, self.rxcominitdet, "sys"),
MultiReg(rxcomwakedet, self.rxcomwakedet, "sys"),
MultiReg(rxdlyresetdone, self.rxdlyresetdone, "sys"),
]
rxelecidle_filter = _LowPassFilter(rxelecidle_i, self.rxelecidle, 256)
self.submodules += rxelecidle_filter
# QPLL input clock
self.qpllclk = Signal()
self.qpllrefclk = Signal()
# Instance
gtxe2_channel_parameters = {
# Simulation-Only Attributes
"p_SIM_RECEIVER_DETECT_PASS": "TRUE",
"p_SIM_TX_EIDLE_DRIVE_LEVEL": "X",
"p_SIM_RESET_SPEEDUP": "TRUE",
"p_SIM_CPLLREFCLK_SEL": 0b001,
"p_SIM_VERSION": "4.0",
# RX Byte and Word Alignment Attributes
"p_ALIGN_COMMA_DOUBLE": "FALSE",
"p_ALIGN_COMMA_ENABLE": ones(10),
"p_ALIGN_COMMA_WORD": 1,
"p_ALIGN_MCOMMA_DET": "TRUE",
"p_ALIGN_MCOMMA_VALUE": 0b1010000011,
"p_ALIGN_PCOMMA_DET": "TRUE",
"p_ALIGN_PCOMMA_VALUE": 0b0101111100,
"p_SHOW_REALIGN_COMMA": "FALSE",
"p_RXSLIDE_AUTO_WAIT": 7,
"p_RXSLIDE_MODE": "PCS",
"p_RX_SIG_VALID_DLY": 10,
# RX 8B/10B Decoder Attributes
"p_RX_DISPERR_SEQ_MATCH": "TRUE",
"p_DEC_MCOMMA_DETECT": "TRUE",
"p_DEC_PCOMMA_DETECT": "TRUE",
"p_DEC_VALID_COMMA_ONLY": "FALSE",
# RX Clock Correction Attributes
"p_CBCC_DATA_SOURCE_SEL": "DECODED",
"p_CLK_COR_SEQ_2_USE": "FALSE",
"p_CLK_COR_KEEP_IDLE": "FALSE",
"p_CLK_COR_MAX_LAT": 9,
"p_CLK_COR_MIN_LAT": 7,
"p_CLK_COR_PRECEDENCE": "TRUE",
"p_CLK_COR_REPEAT_WAIT": 0,
"p_CLK_COR_SEQ_LEN": 1,
"p_CLK_COR_SEQ_1_ENABLE": ones(4),
"p_CLK_COR_SEQ_1_1": 0b0100000000,
"p_CLK_COR_SEQ_1_2": 0b0000000000,
"p_CLK_COR_SEQ_1_3": 0b0000000000,
"p_CLK_COR_SEQ_1_4": 0b0000000000,
"p_CLK_CORRECT_USE": "FALSE",
"p_CLK_COR_SEQ_2_ENABLE": ones(4),
"p_CLK_COR_SEQ_2_1": 0b0100000000,
"p_CLK_COR_SEQ_2_2": 0b0000000000,
"p_CLK_COR_SEQ_2_3": 0b0000000000,
"p_CLK_COR_SEQ_2_4": 0b0000000000,
# RX Channel Bonding Attributes
"p_CHAN_BOND_KEEP_ALIGN": "FALSE",
"p_CHAN_BOND_MAX_SKEW": 1,
"p_CHAN_BOND_SEQ_LEN": 1,
"p_CHAN_BOND_SEQ_1_1": 0,
"p_CHAN_BOND_SEQ_1_1": 0,
"p_CHAN_BOND_SEQ_1_2": 0,
"p_CHAN_BOND_SEQ_1_3": 0,
"p_CHAN_BOND_SEQ_1_4": 0,
"p_CHAN_BOND_SEQ_1_ENABLE": ones(4),
"p_CHAN_BOND_SEQ_2_1": 0,
"p_CHAN_BOND_SEQ_2_2": 0,
"p_CHAN_BOND_SEQ_2_3": 0,
"p_CHAN_BOND_SEQ_2_4": 0,
"p_CHAN_BOND_SEQ_2_ENABLE": ones(4),
"p_CHAN_BOND_SEQ_2_USE": "FALSE",
"p_FTS_DESKEW_SEQ_ENABLE": ones(4),
"p_FTS_LANE_DESKEW_CFG": ones(4),
"p_FTS_LANE_DESKEW_EN": "FALSE",
# RX Margin Analysis Attributes
"p_ES_CONTROL": 0,
"p_ES_ERRDET_EN": "FALSE",
"p_ES_EYE_SCAN_EN": "TRUE",
"p_ES_HORZ_OFFSET": 0,
"p_ES_PMA_CFG": 0,
"p_ES_PRESCALE": 0,
"p_ES_QUALIFIER": 0,
"p_ES_QUAL_MASK": 0,
"p_ES_SDATA_MASK": 0,
"p_ES_VERT_OFFSET": 0,
# FPGA RX Interface Attributes
"p_RX_DATA_WIDTH": 20,
# PMA Attributes
"p_OUTREFCLK_SEL_INV": 0b11,
"p_PMA_RSV": 0x00018480,
"p_PMA_RSV2": 0x2050,
"p_PMA_RSV3": 0,
"p_PMA_RSV4": 0,
"p_RX_BIAS_CFG": 0b100,
"p_DMONITOR_CFG": 0xA00,
"p_RX_CM_SEL": 0b11,
"p_RX_CM_TRIM": 0b010,
"p_RX_DEBUG_CFG": 0,
"p_RX_OS_CFG": 0b10000000,
"p_TERM_RCAL_CFG": 0b10000,
"p_TERM_RCAL_OVRD": 0,
"p_TST_RSV": 0,
"p_RX_CLK25_DIV": 6,
"p_TX_CLK25_DIV": 6,
"p_UCODEER_CLR": 0,
# PCI Express Attributes
"p_PCS_PCIE_EN": "FALSE",
# PCS Attributes
"p_PCS_RSVD_ATTR": 0x100,
# RX Buffer Attributes
"p_RXBUF_ADDR_MODE": "FAST",
"p_RXBUF_EIDLE_HI_CNT": 0b1000,
"p_RXBUF_EIDLE_LO_CNT": 0b0000,
"p_RXBUF_EN": "FALSE",
"p_RX_BUFFER_CFG": 0,
"p_RXBUF_RESET_ON_CB_CHANGE": "TRUE",
"p_RXBUF_RESET_ON_COMMAALIGN": "FALSE",
"p_RXBUF_RESET_ON_EIDLE": "FALSE",
"p_RXBUF_RESET_ON_RATE_CHANGE": "TRUE",
"p_RXBUFRESET_TIME": 1,
"p_RXBUF_THRESH_OVFLW": 61,
"p_RXBUF_THRESH_OVRD": "FALSE",
"p_RXBUF_THRESH_UNDFLW": 4,
"p_RXDLY_CFG": 0x1f,
"p_RXDLY_LCFG": 0x30,
"p_RXDLY_TAP_CFG": 0,
"p_RXPH_CFG": 0,
"p_RXPHDLY_CFG": 0x084020,
"p_RXPH_MONITOR_SEL": 0,
"p_RX_XCLK_SEL": "RXUSR",
"p_RX_DDI_SEL": 0,
"p_RX_DEFER_RESET_BUF_EN": "TRUE",
# CDR Attributes
"p_RXCDR_CFG": rxcdr_cfg,
"p_RXCDR_FR_RESET_ON_EIDLE": 0,
"p_RXCDR_HOLD_DURING_EIDLE": 0,
"p_RXCDR_PH_RESET_ON_EIDLE": 0,
"p_RXCDR_LOCK_CFG": 0b010101,
# RX Initialization and Reset Attributes
"p_RXCDRFREQRESET_TIME": 1,
"p_RXCDRPHRESET_TIME": 1,
"p_RXISCANRESET_TIME": 1,
"p_RXPCSRESET_TIME": 1,
"p_RXPMARESET_TIME": 3,
# RX OOB Signaling Attributes
"p_RXOOB_CFG": 0b0000110,
# RX Gearbox Attributes
"p_RXGEARBOX_EN": "FALSE",
"p_GEARBOX_MODE": 0,
# PRBS Detection Attribute
"p_RXPRBS_ERR_LOOPBACK": 0,
# Power-Down Attributes
"p_PD_TRANS_TIME_FROM_P2": 0x03c,
"p_PD_TRANS_TIME_NONE_P2": 0x3c,
"p_PD_TRANS_TIME_TO_P2": 0x64,
# RX OOB Signaling Attributes
"p_SAS_MAX_COM": 64,
"p_SAS_MIN_COM": 36,
"p_SATA_BURST_SEQ_LEN": 0b0101,
"p_SATA_BURST_VAL": 0b100,
"p_SATA_EIDLE_VAL": 0b100,
"p_SATA_MAX_BURST": 8,
"p_SATA_MAX_INIT": 21,
"p_SATA_MAX_WAKE": 7,
"p_SATA_MIN_BURST": 4,
"p_SATA_MIN_INIT": 12,
"p_SATA_MIN_WAKE": 4,
# RX Fabric Clock Output Control Attributes
"p_TRANS_TIME_RATE": 0x0e,
# TX Buffer Attributes
"p_TXBUF_EN": "FALSE",
"p_TXBUF_RESET_ON_RATE_CHANGE": "FALSE",
"p_TXDLY_CFG": 0x1f,
"p_TXDLY_LCFG": 0x030,
"p_TXDLY_TAP_CFG": 0,
"p_TXPH_CFG": 0x0780,
"p_TXPHDLY_CFG": 0x084020,
"p_TXPH_MONITOR_SEL": 0,
"p_TX_XCLK_SEL": "TXUSR",
# FPGA TX Interface Attributes
"p_TX_DATA_WIDTH": 20,
# TX Configurable Driver Attributes
"p_TX_DEEMPH0": 0,
"p_TX_DEEMPH1": 0,
"p_TX_EIDLE_ASSERT_DELAY": 0b110,
"p_TX_EIDLE_DEASSERT_DELAY": 0b100,
"p_TX_LOOPBACK_DRIVE_HIZ": "FALSE",
"p_TX_MAINCURSOR_SEL": 0,
"p_TX_DRIVE_MODE": "DIRECT",
"p_TX_MARGIN_FULL_0": 0b1001110,
"p_TX_MARGIN_FULL_1": 0b1001001,
"p_TX_MARGIN_FULL_2": 0b1000101,
"p_TX_MARGIN_FULL_3": 0b1000010,
"p_TX_MARGIN_FULL_4": 0b1000000,
"p_TX_MARGIN_LOW_0": 0b1000110,
"p_TX_MARGIN_LOW_1": 0b1000100,
"p_TX_MARGIN_LOW_2": 0b1000010,
"p_TX_MARGIN_LOW_3": 0b1000000,
"p_TX_MARGIN_LOW_4": 0b1000000,
# TX Gearbox Attributes
"p_TXGEARBOX_EN": "FALSE",
# TX Initialization and Reset Attributes
"p_TXPCSRESET_TIME": 1,
"p_TXPMARESET_TIME": 1,
# TX Receiver Detection Attributes
"p_TX_RXDETECT_CFG": 0x1832,
"p_TX_RXDETECT_REF": 0b100,
# CPLL Attributes
"p_CPLL_CFG": 0xBC07DC,
"p_CPLL_FBDIV": 4,
"p_CPLL_FBDIV_45": 5,
"p_CPLL_INIT_CFG": 0x00001e,
"p_CPLL_LOCK_CFG": 0x01e8,
"p_CPLL_REFCLK_DIV": 1,
"p_RXOUT_DIV": rxout_div,
"p_TXOUT_DIV": txout_div,
"p_SATA_CPLL_CFG": "VCO_3000MHZ",
# RX Initialization and Reset Attributes
"p_RXDFELPMRESET_TIME": 0b0001111,
# RX Equalizer Attributes
"p_RXLPM_HF_CFG": 0b00000011110000,
"p_RXLPM_LF_CFG": 0b00000011110000,
"p_RX_DFE_GAIN_CFG": 0x020fea,
"p_RX_DFE_H2_CFG": 0b000000000000,
"p_RX_DFE_H3_CFG": 0b000001000000,
"p_RX_DFE_H4_CFG": 0b00011110000,
"p_RX_DFE_H5_CFG": 0b00011100000,
"p_RX_DFE_KL_CFG": 0b0000011111110,
"p_RX_DFE_LPM_CFG": 0x0954,
"p_RX_DFE_LPM_HOLD_DURING_EIDLE": 1,
"p_RX_DFE_UT_CFG": 0b10001111000000000,
"p_RX_DFE_VP_CFG": 0b00011111100000011,
# Power-Down Attributes
"p_RX_CLKMUX_PD": 1,
"p_TX_CLKMUX_PD": 1,
# FPGA RX Interface Attribute
"p_RX_INT_DATAWIDTH": 0,
# FPGA TX Interface Attribute
"p_TX_INT_DATAWIDTH": 0,
# TX Configurable Driver Attributes
"p_TX_QPI_STATUS_EN": 0,
# RX Equalizer Attributes
"p_RX_DFE_KL_CFG2": 0b00110011000100000001100000001100,
"p_RX_DFE_XYD_CFG": 0b0000000000000,
# TX Configurable Driver Attributes
"p_TX_PREDRIVER_MODE": 0,
}
self.specials += \
Instance("GTXE2_CHANNEL",
# CPLL Ports
#o_CPLLFBCLKLOST=,
o_CPLLLOCK=self.cplllock,
i_CPLLLOCKDETCLK=0,
i_CPLLLOCKEN=1,
i_CPLLPD=0,
#o_CPLLREFCLKLOST=0,
i_CPLLREFCLKSEL=0b001,
i_CPLLRESET=self.cpllreset,
i_GTRSVD=0,
i_PCSRSVDIN=0,
i_PCSRSVDIN2=0,
i_PMARSVDIN=0,
i_PMARSVDIN2=0,
i_TSTIN=ones(20),
#o_TSTOUT=,
# Channel
i_CLKRSVD=0,
# Channel - Clocking Ports
i_GTGREFCLK=0,
i_GTNORTHREFCLK0=0,
i_GTNORTHREFCLK1=0,
i_GTREFCLK0=self.gtrefclk0,
i_GTREFCLK1=0,
i_GTSOUTHREFCLK0=0,
i_GTSOUTHREFCLK1=0,
# Channel - DRP Ports
i_DRPADDR=0,
i_DRPCLK=0,
i_DRPDI=0,
#o_DRPDO=,
i_DRPEN=0,
#o_DRPRDY=,
i_DRPWE=0,
# Clocking Ports
#o_GTREFCLKMONITOR=,
i_QPLLCLK=self.qpllclk,
i_QPLLREFCLK=self.qpllrefclk,
i_RXSYSCLKSEL=0b00,
i_TXSYSCLKSEL=0b00,
# Digital Monitor Ports
#o_DMONITOROUT=,
# FPGA TX Interface Datapath Configuration
i_TX8B10BEN=1,
# Loopback Ports
i_LOOPBACK=0,
# PCI Express Ports
#o_PHYSTATUS=,
i_RXRATE=0,
#o_RXVALID=,
# Power-Down Ports
i_RXPD=0b00,
i_TXPD=0b00,
# RX 8B/10B Decoder Ports
i_SETERRSTATUS=0,
# RX Initialization and Reset Ports
i_EYESCANRESET=0,
i_RXUSERRDY=rxuserrdy,
# RX Margin Analysis Ports
#o_EYESCANDATAERROR=,
i_EYESCANMODE=0,
i_EYESCANTRIGGER=0,
# Receive Ports - CDR Ports
i_RXCDRFREQRESET=0,
i_RXCDRHOLD=0,
#o_RXCDRLOCK=,
i_RXCDROVRDEN=0,
i_RXCDRRESET=0,
i_RXCDRRESETRSV=0,
# Receive Ports - Clock Correction Ports
#o_RXCLKCORCNT=,
# Receive Ports - FPGA RX Interface Datapath Configuration
i_RX8B10BEN=1,
# Receive Ports - FPGA RX Interface Ports
i_RXUSRCLK=self.rxusrclk,
i_RXUSRCLK2=self.rxusrclk2,
# Receive Ports - FPGA RX interface Ports
o_RXDATA=self.rxdata,
# Receive Ports - Pattern Checker Ports
#o_RXPRBSERR=,
i_RXPRBSSEL=0,
# Receive Ports - Pattern Checker ports
i_RXPRBSCNTRESET=0,
# Receive Ports - RX Equalizer Ports
i_RXDFEXYDEN=1,
i_RXDFEXYDHOLD=0,
i_RXDFEXYDOVRDEN=0,
# Receive Ports - RX 8B/10B Decoder Ports
#o_RXDISPERR=,
#o_RXNOTINTABLE=,
# Receive Ports - RX AFE
i_GTXRXP=pads.rxp,
i_GTXRXN=pads.rxn,
# Receive Ports - RX Buffer Bypass Ports
i_RXBUFRESET=0,
#o_RXBUFSTATUS=,
i_RXDDIEN=1,
i_RXDLYBYPASS=0,
i_RXDLYEN=0,
i_RXDLYOVRDEN=0,
i_RXDLYSRESET=rxdlyreset,
o_RXDLYSRESETDONE=rxdlyresetdone,
i_RXPHALIGN=0,
#o_RXPHALIGNDONE=,
i_RXPHALIGNEN=0,
i_RXPHDLYPD=0,
i_RXPHDLYRESET=0,
#o_RXPHMONITOR=,
i_RXPHOVRDEN=0,
#o_RXPHSLIPMONITOR=,
#o_RXSTATUS=,
# Receive Ports - RX Byte and Word Alignment Ports
#o_RXBYTEISALIGNED=,
#o_RXBYTEREALIGN=,
#o_RXCOMMADET=,
i_RXCOMMADETEN=1,
i_RXMCOMMAALIGNEN=1,
i_RXPCOMMAALIGNEN=1,
# Receive Ports - RX Channel Bonding Ports
#o_RXCHANBONDSEQ=,
i_RXCHBONDEN=0,
i_RXCHBONDLEVEL=0,
i_RXCHBONDMASTER=0,
#o_RXCHBONDO=,
i_RXCHBONDSLAVE=0,
# Receive Ports - RX Channel Bonding Ports
#o_RXCHANISALIGNED=,
#o_RXCHANREALIGN=,
# Receive Ports - RX Equalizer Ports
i_RXDFEAGCHOLD=0,
i_RXDFEAGCOVRDEN=0,
i_RXDFECM1EN=0,
i_RXDFELFHOLD=0,
i_RXDFELFOVRDEN=0,
i_RXDFELPMRESET=0,
i_RXDFETAP2HOLD=0,
i_RXDFETAP2OVRDEN=0,
i_RXDFETAP3HOLD=0,
i_RXDFETAP3OVRDEN=0,
i_RXDFETAP4HOLD=0,
i_RXDFETAP4OVRDEN=0,
i_RXDFETAP5HOLD=0,
i_RXDFETAP5OVRDEN=0,
i_RXDFEUTHOLD=0,
i_RXDFEUTOVRDEN=0,
i_RXDFEVPHOLD=0,
i_RXDFEVPOVRDEN=0,
i_RXDFEVSEN=0,
i_RXLPMLFKLOVRDEN=0,
#o_RXMONITOROUT=,
i_RXMONITORSEL=0b00,
i_RXOSHOLD=0,
i_RXOSOVRDEN=0,
# Receive Ports - RX Equilizer Ports
i_RXLPMHFHOLD=0,
i_RXLPMHFOVRDEN=0,
i_RXLPMLFHOLD=0,
# Receive Ports - RX Fabric ClocK Output Control Ports
#o_RXRATEDONE=,
# Receive Ports - RX Fabric Output Control Ports
o_RXOUTCLK=self.rxoutclk,
#o_RXOUTCLKFABRIC=,
#o_RXOUTCLKPCS=,
i_RXOUTCLKSEL=0b010,
# Receive Ports - RX Gearbox Ports
#o_RXDATAVALID=,
#o_RXHEADER=,
#o_RXHEADERVALID=,
#o_RXSTARTOFSEQ=,
# Receive Ports - RX Gearbox Ports
i_RXGEARBOXSLIP=0,
# Receive Ports - RX Initialization and Reset Ports
i_GTRXRESET=self.gtrxreset,
i_RXOOBRESET=0,
i_RXPCSRESET=0,
i_RXPMARESET=0,
# Receive Ports - RX Margin Analysis ports
i_RXLPMEN=0,
# Receive Ports - RX OOB Signaling ports
#o_RXCOMSASDET=,
o_RXCOMWAKEDET=rxcomwakedet,
# Receive Ports - RX OOB Signaling ports
o_RXCOMINITDET=rxcominitdet,
# Receive Ports - RX OOB signalling Ports
o_RXELECIDLE=rxelecidle,
i_RXELECIDLEMODE=0b00,
# Receive Ports - RX Polarity Control Ports
i_RXPOLARITY=0,
# Receive Ports - RX gearbox ports
i_RXSLIDE=0,
# Receive Ports - RX8B/10B Decoder Ports
#o_RXCHARISCOMMA=,
o_RXCHARISK=self.rxcharisk,
# Receive Ports - Rx Channel Bonding Ports
i_RXCHBONDI=0,
# Receive Ports -RX Initialization and Reset Ports
o_RXRESETDONE=rxresetdone,
# Rx AFE Ports
i_RXQPIEN=0,
#o_RXQPISENN=,
#o_RXQPISENP=,
# TX Buffer Bypass Ports
i_TXPHDLYTSTCLK=0,
# TX Configurable Driver Ports
i_TXPOSTCURSOR=0,
i_TXPOSTCURSORINV=0,
i_TXPRECURSOR=0,
i_TXPRECURSORINV=0,
i_TXQPIBIASEN=0,
i_TXQPISTRONGPDOWN=0,
i_TXQPIWEAKPUP=0,
# TX Initialization and Reset Ports
i_CFGRESET=0,
i_GTTXRESET=gttxreset,
#o_PCSRSVDOUT=,
i_TXUSERRDY=txuserrdy,
# Transceiver Reset Mode Operation
i_GTRESETSEL=0,
i_RESETOVRD=0,
# Transmit Ports - 8b10b Encoder Control Ports
i_TXCHARDISPMODE=0,
i_TXCHARDISPVAL=0,
# Transmit Ports - FPGA TX Interface Ports
i_TXUSRCLK=self.txusrclk,
i_TXUSRCLK2=self.txusrclk2,
# Transmit Ports - PCI Express Ports
i_TXELECIDLE=txelecidle,
i_TXMARGIN=0,
i_TXRATE=0,
i_TXSWING=0,
# Transmit Ports - Pattern Generator Ports
i_TXPRBSFORCEERR=0,
# Transmit Ports - TX Buffer Bypass Ports
i_TXDLYBYPASS=0,
i_TXDLYEN=0,
i_TXDLYHOLD=0,
i_TXDLYOVRDEN=0,
i_TXDLYSRESET=txdlyreset,
o_TXDLYSRESETDONE=txdlyresetdone,
i_TXDLYUPDOWN=0,
i_TXPHALIGN=0,
#o_TXPHALIGNDONE=txphaligndone,
i_TXPHALIGNEN=0,
i_TXPHDLYPD=0,
i_TXPHDLYRESET=0,
i_TXPHINIT=0,
#o_TXPHINITDONE=,
i_TXPHOVRDEN=0,
# Transmit Ports - TX Buffer Ports
#o_TXBUFSTATUS=,
# Transmit Ports - TX Configurable Driver Ports
i_TXBUFDIFFCTRL=0b100,
i_TXDEEMPH=0,
i_TXDIFFCTRL=0b1000,
i_TXDIFFPD=0,
i_TXINHIBIT=0,
i_TXMAINCURSOR=0,
i_TXPISOPD=0,
# Transmit Ports - TX Data Path interface
i_TXDATA=self.txdata,
# Transmit Ports - TX Driver and OOB signaling
o_GTXTXP=pads.txp,
o_GTXTXN=pads.txn,
# Transmit Ports - TX Fabric Clock Output Control Ports
o_TXOUTCLK=self.txoutclk,
#o_TXOUTCLKFABRIC=,
#o_TXOUTCLKPCS=,
i_TXOUTCLKSEL=0b11,
#o_TXRATEDONE=,
# Transmit Ports - TX Gearbox Ports
i_TXCHARISK=self.txcharisk,
#o_TXGEARBOXREADY=,
i_TXHEADER=0,
i_TXSEQUENCE=0,
i_TXSTARTSEQ=0,
# Transmit Ports - TX Initialization and Reset Ports
i_TXPCSRESET=0,
i_TXPMARESET=0,
o_TXRESETDONE=txresetdone,
# Transmit Ports - TX OOB signalling Ports
o_TXCOMFINISH=txcomfinish,
i_TXCOMINIT=txcominit,
i_TXCOMSAS=0,
i_TXCOMWAKE=txcomwake,
i_TXPDELECIDLEMODE=0,
# Transmit Ports - TX Polarity Control Ports
i_TXPOLARITY=0,
# Transmit Ports - TX Receiver Detection Ports
i_TXDETECTRX=0,
# Transmit Ports - TX8b/10b Encoder Ports
i_TX8B10BBYPASS=0,
# Transmit Ports - pattern Generator Ports
i_TXPRBSSEL=0,
# Tx Configurable Driver Ports
#o_TXQPISENN=,
#o_TXQPISENP=,
**gtxe2_channel_parameters
)