change converter code to drive new verilog

software/src/io.c

@@ -8,113 +8,59 @@ LOG_MODULE_REGISTER(adc_dac_io);
 #define CSR_LOCATIONS
 #include "pin_io.h"
 
+static int32_t
+sign_extend(uint32_t n, unsigned wid)
+{
+	if (n >> (wid - 1))
+		return (int32_t) (~((uint32_t) 0) & n);
+	else
+		return (int32_t) n;
+}
+
 int32_t
 adc_read(size_t num, unsigned wid)
 {
-	uint32_t buf = 0;
-
 	if (num >= ADC_MAX) {
-		LOG_ERR("Bad ADC %d\n", num);
+		LOG_ERR("adc_read got bad ADC %zd\n", num);
 		k_fatal_halt(K_ERR_KERNEL_OOPS);
 	}
 	if (wid > 32) {
-		LOG_ERR("Bad ADC Width %u\n", wid);
+		LOG_ERR("adc_read got bad width %u\n", wid);
 		k_fatal_halt(K_ERR_KERNEL_OOPS);
 	}
 
-	/* SCK is set low because data is changed at the rising edge. */
-	*adc_sck[num] = 0;
 	*adc_conv[num] = 1;
-
-	/* Wait setup time.
-	 * The ADC sends an interrupt signal to notify the master that
-	 * the ADC is ready to read out the data, but the evaluation boards
-	 * do not expose that signal. This code relies on the maximum times
-	 * listed in the datasheets.
-	 *
-	 * The ADCs have different maximum conversion times, so the longest
-	 * one (LTC2328) is used. This number also includes t_BUSYLH.
-	 */
 	k_sleep(K_NSEC(550));
+	*adc_arm[num] = 1;
 	*adc_conv[num] = 0;
+	// XXX: Guess
+	k_sleep(K_MSEC(40));
+	while (!*adc_finished[num]);
 
-	for (int i = 0; i < wid; i++) {
+	uint32_t buf = *adc_from_slave[num];
-		k_sleep(K_NSEC(20));
+	*adc_arm[num] = 0;
-		buf <<= 1;
+	return sign_extend(buf);
-		buf |= *adc_sdo[num];
-
-		*adc_sck[num] = 1;
-		k_sleep(K_NSEC(20));
-		*adc_sck[num] = 0;
 }
 
-	/* Sign extension.
-	 * LT ADCs return twos-complement integers. They can be either positive
-	 * or negative, and this is determined by the MSB (MSB = 1 means
-	 * negative number).
-	 *
-	 * The ADCs do not send 32 bit integers, so the integers that are
-	 * received must be sign extended.
-	 *
-	 * If a number is positive, no conversion is necessary.
-	 *
-	 * If a number is negative, then all bits beyond the original MSB
-	 * must be set to 1. This can be done by ANDing the received number
-	 * with all-bits-1.
-	 *
-	 * As an example, the negative 6-bit number
-	 *   101101
-	 * can be sign extended to 8-bit by
-	 *     11111111
-	 *   & 00101101
-	 *   ==========
-	 *     11101101
-	 *      (101101)
-	 */
-	if (buf >> wid)
-		return (int32_t) (~((uint32_t) 0) & buf);
-	else
-		return (int32_t) buf;
-}
-
-#define DAC_SS(n, v) *dac_ctrl[(n)] |= (v & 1) << 2
-#define DAC_SCK(n, v) *dac_ctrl[(n)] |= (v & 1) << 1
-#define DAC_MOSI(n, v) *dac_ctrl[(n)] |= (v & 1)
-#define DAC_MISO(n) *dac_miso[(n)]
-
-/* Thankfully we only have one type of DAC (for now).
- * AD DACs are register-based devices. To write to a register,
- * 1) Set SCK high.
- * 2) Set SS high in software (SYNC is active-low), wait setup time.
- * 3) Set SCK low.
- * 4) Read MISO, write MOSI.
- * 5) Set SCK high, wait setup time.
-*/
 uint32_t
 dac_write_raw(size_t n, uint32_t data)
 {
-	uint32_t r = 0;
-	DAC_SCK(n, 1);
-	DAC_SS(n, 1);
-	k_sleep(K_NSEC(10));
-
 	if (n >= DAC_MAX) {
 		LOG_ERR("dac_write_raw got bad ADC %d\n", n);
 		k_fatal_halt(K_ERR_KERNEL_OOPS);
 	}
 
-	for (int i = 0; i < 24; i++) {
+	*dac_to_slave[n] = data;
-		DAC_SCK(n, 0);
+	*dac_ss[n] = 1;
-		DAC_MOSI(n, data >> 31 & 1);
+	k_sleep(K_NSEC(20));
-		k_sleep(K_NSEC(500));
+	*dac_arm[n] = 1;
-
+	// XXX: Guess
-		r <<= 1;
+	k_sleep(K_MSEC(50));
-		data <<= 1;
+	while (!*dac_finished[num]);
-		r |= DAC_MISO(n) & 1;
-		DAC_SCK(n, 1);
-		k_sleep(K_NSEC(500));
-	}
 
+	*dac_ss[n] = 0;
+	uint32_t r = *dac_from_slave[n];
+	*dac_arm[n] = 0;
 	return r;
 }