131 lines
3.9 KiB
Markdown
131 lines
3.9 KiB
Markdown
Upsilon docker development environment setup.
|
|
|
|
# Dockerfile style guide
|
|
|
|
Dockerfiles should be simple. The Dockerfiles should be readable to a
|
|
beginner.
|
|
|
|
# Setup steps
|
|
|
|
Do all of the following in the `build` folder.
|
|
|
|
## Installing OpenFPGALoader
|
|
|
|
Install [openFPGALoader][1]. If this program is not in your repositories,
|
|
run `make openFPGALoader` to fetch and build the program. This will install
|
|
openFPGALoader locally.
|
|
|
|
Even if you install openFPGALoader locally, there are some files (udev rules)
|
|
that must be installed with administrative privleges. Check the documentation
|
|
for openFPGALoader.
|
|
|
|
[1]: https://trabucayre.github.io/openFPGALoader/index.html
|
|
|
|
## Setup Rootless Docker
|
|
|
|
Docker allows you to run programs in containers, which are isolated
|
|
environments. Build environments can be set up automatically, and re-setup
|
|
whenever needed.
|
|
|
|
If you have issues with docker, try adding to `~/.config/docker/daemon.json`
|
|
|
|
{
|
|
"storage-driver": "fuse-overlayfs"
|
|
}
|
|
|
|
|
|
## Download and Install Python3
|
|
|
|
Install `python3` and `python3-pip`.
|
|
|
|
## Clone External Repositories
|
|
|
|
Run `make clone`. You may need to download the upsilon repositories
|
|
and put them in the same folder as the Makefile.
|
|
|
|
## Setup Network
|
|
|
|
Plug in your router/switch to an ethernet port on your computer. If your
|
|
computer is usually wired to the network, you will need another ethernet
|
|
port (a PCI card is ideal, but a USB-Ethernet port works).
|
|
|
|
Set the ethernet port to static ip `192.168.1.100/24`, netmask `255.255.255.0`,
|
|
gateway `192.168.1.1`. Make sure this is not the default route. Make sure
|
|
to adjust your firewall to allow traffic on the 192.168.1.0/24 range.
|
|
|
|
If your local network already uses the 192.168.1.0/24 range, then you must
|
|
modify `upsilon/firmware/soc.py` to use different IPs. You must rebuild the
|
|
SoC after doing this.
|
|
|
|
## Setup Images
|
|
|
|
Run `make images` to create all docker images.
|
|
|
|
## Setup and Run Containers
|
|
|
|
For `NAME` in `hardware`, `opensbi`, `buildroot`:
|
|
|
|
1. Run `make $NAME-container` to build the container. You usually only need
|
|
to do this once.
|
|
2. If the container already exists, do `docker container start upsilon-$NAME`.
|
|
3. Run `make $NAME-copy` to copy Upsilon's code into the container.
|
|
4. Run `make $NAME-execute` to build the data.
|
|
5. Run `make $NAME-get` to retrieve the build artefacts.
|
|
|
|
If you do not delete the container you can run
|
|
|
|
make $NAME-copy $NAME-execute $NAME-get
|
|
|
|
when you need to rebuild. If you need shell access, run `make $NAME-shell`.
|
|
|
|
## Launch TFTP Server
|
|
|
|
Install py3tftp (`pip3 install --user py3tftp`). Then run `make tftp` to
|
|
launch the TFTP server. Keep this terminal open.
|
|
|
|
## Flash FPGA
|
|
|
|
Plug in your FPGA into the USB slot. If you have installed openFPGALoader
|
|
by your package manager, run `make OPENFPGALOADER=openfpgaloader flash`.
|
|
If you installed it using `make openFPGALoader`, then just run `make flash`.
|
|
|
|
In a second you should see messages in the TFTP terminal. This means your
|
|
controller is sucessfully connected to your computer.
|
|
|
|
## SSH Access
|
|
|
|
Add the following to your SSH config:
|
|
|
|
Host upsilon
|
|
HostName 192.168.1.50
|
|
StrictHostKeyChecking no
|
|
UserKnownHostsFile /dev/null
|
|
IdentityFile upsilon_key
|
|
User root
|
|
LogLevel QUIET
|
|
|
|
Then copy the file `build/upsilon_key` to `$HOME/.ssh`.
|
|
|
|
When the FPGA is connected you can access it with `ssh upsilon` (password
|
|
`upsilon`).
|
|
|
|
Wait about a minute for Linux to boot.
|
|
|
|
## Launch FPGA Shell (Optional)
|
|
|
|
If you cannot access the FPGA through SSH, you can launch a shell through
|
|
UART.
|
|
|
|
You will need to install [LiteX](https://github.com/enjoy-digital/litex).
|
|
Download and run `litex_setup.py`.
|
|
|
|
Run `litex_term /dev/ttyUSB1`. You should get messages in the window with
|
|
the TFTP server that the FPGA has connected to the server. Eventually you
|
|
will get a login prompt (username `root` password `upsilon`).
|
|
|
|
## Copy Library
|
|
|
|
Run `make copy` to copy the Micropython Upsilon library to the FPGA. After
|
|
this the modules `comm` and `mmio` are available when running scripts in
|
|
`/root`.
|