upsilon/doc/verilog_manual.md

11 KiB

Copyright 2023 (C) Peter McGoron.

This file is a part of Upsilon, a free and open source software project. For license terms, refer to the files in doc/copying in the Upsilon source distribution.


This document is from when there was a substantial amount of hand-written Verilog in this project, and hence is out of date. It is kept here because it is a good introduction to FPGAs. For more recent information, see /doc/gateware.rst .

The Hardware Maintenance Manual is an overview of the hardware (non-software) parts of Upsilon.

Crash Course in FPGAs

Upsilon runs on a Field Programmable Gate Array (FPGA). FPGAs are sets of logic gates and other peripherals that can be changed by a computer. FPGAs can implement CPUs, digital filters, and control code at a much higher speed than a computer. The downside is that FPGAs are much more difficult to program for.

A large part of Upsilon is written in Verilog. Verilog is a Hardware Description Language (HDL), which is similar to a programming language (such as C++ or Python).

The difference is, is that Verilog compiles to a piece of hardware that deals with individual bits executing operations in sync with a clock. This differs from a piece of software, which is a set of instructions that a computer follows. Verilog is usually much less abstract than regular code.

Regular code is tested on the system in which it is run. Hardware, on the other hand, is very difficult to test on the device that it is actually running on. Hardware is usually simulated. This project primarily simulates Verilog code using the program Verilator, where the code that runs the simulation is written in C++.

Instead of strings, integers, and classes, the basic components of all Verilog code is the wire and the register, which store bits (1 and 0). Wires connect components together, and registers store data, in a similar way to variables in software. Unlike usual programming languages, where code executes one step at a time, most FPGA code runs at the tick of a clock. Each block of code exceutes in parallel.

To compile Verilog to a format suitable for execution on an FPGA, you synthesize the Verilog into a low-level format that uses the specific resources of the FPGA you are using, and then you run a place and route program to allocate resources on the FPGA to fit your design. Running synthesis on its own can help you understand how much resources a module uses. Place-and-route gives you timing reports, which tell you about major design problems that outstrip the capabilities of the FPGA (or the programs you are using). You should look up what "timing" on an FPGA is and learn as much as you can about it, because it is an issue that does not happen in standard software and can be very difficult to fix when you run into it.

Once a bitstream is synthesized, it is loaded onto a FPGA through a cable (for this project, openFPGALoader).

Recommendations for Learners

Kishore Mishra. Advanced Chip Design.

Gisselquist Technology is the best free online resource for FPGA programming out there. These articles will help you understand how to write good FPGA code, not just valid code.

Here are some exercises for you to ease yourself into FPGA programming.

  • Write an FPGA program that implements addition without using the + operator. This program should add each number bit by bit, handling carried digits properly. This is called a full adder.
  • Write an FPGA program that multiplies two signed integers together, without using the * operator. The width of these integers should not be hard-coded: it should be easy to change. What you write in this is something that is actually a part of this project: see boothmul.v. You do not (and should not!) write it just like Upsilon has written it.
  • Write an FPGA program that communicates over SPI. For simplicity, you only need to write it for a single SPI mode: look up on the internet for details. There is an SPI slave device in this repository that you can use to simulate an end for the SPI master you write, but you should write the SPI slave yourself. For bonus points, connect your SPI master to a real SPI device and confirm that your communication works.

For each of these exercises, follow the complete "Design Testing Process" below. At the very least, write simulations and test your programs on real hardware.

Verilog Programming Guidelines

See also Dan Gisselquist's rules for FPGA development.

  • Use free and open source IP only. IP must be compatible with both the GPL v3.0 and the CERN OHL-v2-S.
  • Stick to Verilog 2005. F4PGA will accept SystemVerilog but yosys sometimes synthesizes it incorrectly.
  • Do not use parameters that are calculated from other parameters (yosys will not parse them correctly). Use m4 macros instead.
  • Do not use Verilog macros. Use m4.
  • Do all code and test generation in Makefiles.
  • Simulate every module, even the trivial ones using Verilator. Simulation must be simulatable with open-source software (Verilator is preferred, but Icarus Verilog and similar are fine). Put test code in the same directory as the Verilog module, unless the Verilog module is external.
  • Synthesize and verify large modules independently on hardware using the LiteX SoC generator. Put the generator source code (along with the hardware test driver) in the repository.
  • Write only synthesizable verilog (except for direct test-bench code), even for modules that will not be synthesized.
  • Dump traces using .fst format.
  • Use only one clock.
  • Only transition on the positive edge of the system clock.
  • Do not use asynchronous resets.
  • Don't write Wishbone bus code in Verilog modules. LiteX automatically takes care of connecting modules together and assigning each register a memory location.
  • Keep all Verilog as generic as possible.
  • Always initialize registers.
  • Rerun tests after every change to the module.

Conventions

Wires

  • When specfying widths, include the total bit width and subtract 1 from it, even in cases where the bit width is constant. For example, to declare an 8-bit register, write reg [8-1:0] r1.
  • If a wire is active low, append _L to the end of the name.

Parameters

  • Parameters are always in all caps.
  • Parameters ending in _WID are bit widths that do not have an associated number (eg DAC widths, input register sizes).
  • Parameters ending in _SIZ are the amount of bits required to store a certain number. These parameters can be calculated using floor(log2(number) + 1). For example,
    • 255 has a SIZ of 8 (8 bits are required to store 255).
    • 256 has a SIZ of 9
    • 254, 253, etc. have a SIZ of 8
    • 127 has a SIZ of 7

Design Testing Process

Simulation

When you write or modify a verilog module, the first thing you should do is write/run a simulation of that module. A simulation of that module should at the minimum compare the execution of the module with known results (called "Ground truth testing"). A simulation should also consider edge cases that you might overlook when writing Verilog.

For example, a module that multiplies two signed integers together should have a simulation that sends the module many pairs of integers, taking care to ensure that all possible permutations of sign are tested (i.e. positive times positive, negative times positive, etc.) and also that special-cases are handled (i.e. largest 32-bit integer multiplied by largest negative 32-bit integer, multiplication by 0 and 1, etc.).

Writing simulation code is a very boring task, but you must do it. Otherwise there is no way for you to check that

  1. Your code does what you want it to do
  2. Any changes you make to your code don't break it

If you find a bug that isn't covered by your simulation, make sure you add that case to the simulation.

The file firmware/rtl/testbench.hpp contains a class that you should use to organize individual tests. Make a derived class of TB and use the posedge() function to encode what default actions your test should take at every positive edge of the clock. Remember, in C++ each action is blocking: there is no equivalent to the non-blocking <=.

If you have to do a lot of non-blocking code for your test, you should write a Verilog wrapper for your test that implements the non-blocking code. Verilator only supports a subset of non-synthesizable Verilog. Unless you really need to, use synthesizable Verilog only. See firmware/rtl/waveform/waveform_sim.v and firmware/rtl/waveform/dma_sim.v for an example of Verilog files only used for tests.

Test Synthesis

Yosys only accepts a subset of Verilog. You might write a bunch of code that Verilator will happily simulate but that will fail to go through Yosys.

Once you have simulated your design, you should use yosys to synthesize it. This will allow you to understand how much and what resources the module is taking up. To do this, you can put the follwing in a script file:

read_verilog module_1.v
read_verilog module_2.v
...
read_verilog top_module.v
synth_xilinx -flatten -nosrl -noclkbuf -nodsp -iopad -nowidelut
write_verilog yosys_synth_output.v

and run yosys -s scriptfile. The options to synth_xilinx reflect the current limitations that F4PGA has. The file xc7.f4pga.tcl that F4PGA downloads is the complete synthesis script, read it to understand the internals of what F4PGA does to compile your verilog.

Test Compilation

I haven't been able to do this for most of this project. The basic idea is to use firmware/rtl/soc.py to load only the module to test, and to use LiteScope to write and read values from the module. For more information, you can look at the boothmul test.

Formal Verification

This isn't used for this project but it really should.

LiteX and F4PGA

LiteX is a System on a Chip builder written in Python. It easily integrates Verilog modules and large system components (CPU, RAM, Ethernet) into a design using a Python script.

All code written for LiteX is in gateware/soc.py. Run this script to build the gateware. If you need to add new modules, you can add them to the design by modifying the Base and the UpsilonSoC class.

All the code that you need to understand in soc.py is heavily documented. (If it's not, that means I don't understand it.)

F4PGA is an open source synthesis suite. LiteX handles F4PGA for you (most of the time).

You should use the Dockerfiles included with upsilon. They are simple and are pinned to the latest known stable version that can build Upsilon. If you really want to install LiteX and F4PGA to your system, just follow the commands in the docker files.