1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
|
/* (c) Peter McGoron 2022 v0.3
* This Source Code Form is subject to the terms of the Mozilla Public
* License, v.2.0. If a copy of the MPL was not distributed with this
* file, You can obtain one at https://mozilla.org/MPL/2.0/.
*/
module
`ifdef SPI_SLAVE_NO_READ
spi_slave_no_read
`elsif SPI_SLAVE_NO_WRITE
spi_slave_no_write
`else
spi_slave
`endif
#(
parameter WID = 24, // Width of bits per transaction.
parameter WID_LEN = 5, // Length in bits required to store WID
parameter POLARITY = 0,
parameter PHASE = 0 // 0 = rising-read falling-write, 1 = rising-write falling-read.
)
(
input clk,
input rst_L,
input sck,
input ss_L,
`ifndef SPI_SLAVE_NO_READ
output reg [WID-1:0] from_master,
input mosi,
`endif
`ifndef SPI_SLAVE_NO_WRITE
input [WID-1:0] to_master,
output reg miso,
`endif
output reg finished,
input rdy,
output reg err
);
`ifndef SPI_SLAVE_NO_READ
/* MOSI is almost always an external wire, so buffer it. */
reg mosi_hot = 0;
reg read_mosi = 0;
always @ (posedge clk) begin
read_mosi <= mosi_hot;
mosi_hot <= mosi;
end
`endif
wire ss = !ss_L;
reg sck_delay = 0;
reg [WID_LEN-1:0] bit_counter = 0;
reg ss_delay = 0;
reg ready_at_start = 0;
`ifndef SPI_SLAVE_NO_WRITE
reg [WID-1:0] send_buf = 0;
`endif
task read_data();
`ifndef SPI_SLAVE_NO_READ
from_master <= from_master << 1;
from_master[0] <= read_mosi;
`endif
endtask
task write_data();
`ifndef SPI_SLAVE_NO_WRITE
send_buf <= send_buf << 1;
miso <= send_buf[WID-1];
`endif
endtask
task setup_bits();
`ifndef SPI_SLAVE_NO_WRITE
/* at Mode 00, the transmission starts with
* a rising edge, and at mode 11, it starts with a falling
* edge. For both modes, these are READs.
*
* For mode 01 and mode 10, the first action is a WRITE.
*/
if (POLARITY == PHASE) begin
miso <= to_master[WID-1];
send_buf <= to_master << 1;
end else begin
send_buf <= to_master;
end
`endif
endtask
task check_counter();
if (bit_counter == WID[WID_LEN-1:0]) begin
err <= ready_at_start;
end else begin
bit_counter <= bit_counter + 1;
end
endtask
always @ (posedge clk) begin
if (!rst_L) begin
sck_delay <= 0;
bit_counter <= 0;
ss_delay <= 0;
ready_at_start <= 0;
`ifndef SPI_SLAVE_NO_READ
from_master <= 0;
`endif
`ifndef SPI_SLAVE_NO_WRITE
miso <= 0;
send_buf <= 0;
`endif
finished <= 0;
err <= 0;
end else begin
sck_delay <= sck;
ss_delay <= ss;
case ({ss_delay, ss})
2'b01: begin // rising edge of SS
bit_counter <= 0;
finished <= 0;
err <= 0;
ready_at_start <= rdy;
setup_bits();
end
2'b10: begin // falling edge
finished <= ready_at_start;
end
2'b11: begin
case ({sck_delay, sck})
2'b01: begin // rising edge
if (PHASE == 1) begin
write_data();
end else begin
read_data();
end
if (POLARITY == 0) begin
check_counter();
end
end
2'b10: begin // falling edge
if (PHASE == 1) begin
read_data();
end else begin
write_data();
end
if (POLARITY == 1) begin
check_counter();
end
end
default: ;
endcase
end
2'b00: if (!rdy) begin
finished <= 0;
err <= 0;
end
endcase
end
end
endmodule
|
