picorv32/README.md

PicoRV32 - A Size-Optimized RISC-V CPU

PicoRV32 is a CPU core that implements the RISC-V RV32I Instruction Set.

Tools (gcc, binutils, etc..) can be obtained via the RISC-V Website.

PicoRV32 is free and open hardware licensed under the ISC license (a license that is similar in terms to the MIT license or the 2-clause BSD license).

Features and Typical Applications:

• Small (~1000 LUTs in a 7-Series Xilinx FGPA)
• High fMAX (>250 MHz on 7-Series Xilinx FGPAs)
• Selectable native memory interface or AXI4-Lite master

This CPU is meant to be used as auxiliary processor in FPGA designs and ASICs. Due to its high fMAX it can be integrated in most existing designs without crossing clock domains. When operated on a lower frequency, it will have a lot of timing slack and thus can be added to a design without compromising timing closure.

For even smaller size it is possible disable support for registers x16..x31 as well as RDCYCLE[H], RDTIME[H], and RDINSTRET[H] instructions, turning the processor into an RV32E core.

Furthermore it is possible to choose between a single-port and a dual-port register file implementation. The former provides better performance while the latter results in a smaller core.

Note: In architectures that implement the register file in dedicated memory resources, such as many FPGAs, disabling the 16 upper registers and/or disabling the dual-port register file may not further reduce the core size.

The core exists in two variations: picorv32 and picorv32_axi. The former provides a simple native memory interface, that is easy to use in simple environments, and the latter provides an AXI-4 Lite Master interface that can easily be integrated with existing systems that are already using the AXI standard.

A separate core picorv32_axi_adapter is provided to bridge between the native memory interface and AXI4. This core can be used to create custom cores that include one or more PicoRV32 cores together with local RAM, ROM, and memory-mapped peripherals, communicating with each other using the native interface, and communicating with the outside world via AXI4.

Parameters:

The following Verilog module parameters can be used to configure the PicoRV32 core.

ENABLE_COUNTERS (default = 1)

This parameter enables support for the RDCYCLE[H], RDTIME[H], and RDINSTRET[H] instructions. This instructions will cause a hardware trap (like any other unsupported instruction) if ENABLE_COUNTERS is set to zero.

Note: Strictly speaking the RDCYCLE[H], RDTIME[H], and RDINSTRET[H] instructions are not optional for an RV32I core. But chances are they are not going to be missed after the application code has been debugged and profiled. This instructions are optional for an RV32E core.

ENABLE_REGS_16_31 (default = 1)

This parameter enables support for registers the x16..x31. The RV32E ISA excludes this registers. However, the RV32E ISA spec requires a hardware trap for when code tries to access this registers. This is not implemented in PicoRV32.

ENABLE_REGS_DUALPORT (default = 1)

The register file can be implemented with two or one read ports. A dual ported register file improves performance a bit, but can also increase the size of the core.

LATCHED_MEM_RDATA (default = 0)

Set this to 1 if the mem_rdata is kept stable by the external circuit after a transaction. In the default configuration the PicoRV32 core only expects the mem_rdata input to be valid in the cycle with mem_valid && mem_ready and latches the value internally.

ENABLE_EXTERNAL_IRQ (default = 0)

Set this to 1 to enable external IRQs.

ENABLE_ILLINSTR_IRQ (default = 0)

Set this to 1 to enable the illegal instruction IRQ. This can be used for software implementations of instructions such as MUL and DIV.

ENABLE_TIMER_IRQ (default = 0)

Set this to 1 to enable the built-in timer and timer IRQ.

PROGADDR_RESET (default = 0)

The start address of the program.

PROGADDR_IRQ (default = 16)

The start address of the interrupt handler.

Performance:

A short reminder: This core is optimized for size, not performance.

Unless stated otherwise, the following numbers apply to a PicoRV32 with ENABLE_REGS_DUALPORT active and connected to a memory that can accomodate requests within one clock cycle.

The average Cycles per Instruction (CPI) is 4 to 5, depending on the mix of instructions in the code. The CPI numbers for the individual instructions can be found in the table below. The column "CPI (SP)" contains the CPI numbers for a core built without ENABLE_REGS_DUALPORT.

Instruction	CPI	CPI (SP)
direct jump (jal)	3	3
ALU reg + immediate	3	3
ALU reg + reg	3	4
branch (not taken)	3	4
memory load	5	5
memory store	5	6
branch (taken)	5	6
indirect jump (jalr)	6	6
shift operations	4-14	4-15

Dhrystone benchmark results: 0.309 DMIPS/MHz (544 Dhrystones/Second/MHz)

For the Dhrystone benchmark the average CPI is 4.167.

Custom Instructions for IRQ Handling

The following custom instructions are supported when IRQs are enabled.

The core has 4 additional 32-bit registers q0 .. q3 that are used for IRQ handling. When an IRQ triggers, the register q0 contains the return address and q1 contains the IRQ number. Registers q2 and q3 are uninitialized and can be used as temporary storage when saving/restoring register values in the IRQ handler.

getq rd, qs

This instruction copies the value from a q-register to a general-purpose register. The Instruction is encoded under the custom0 opcode:

0000000 00000 000XX 000 XXXXX 0001011
f7      f5    qs    f3  rd    opcode

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
getq x5, q2	custom0 5, 2, 0, 0
getq x3, q0	custom0 3, 0, 0, 0
getq x1, q3	custom0 1, 3, 0, 0

setq qd, rs

This instruction copies the value from a general-purpose register to a q-register. The Instruction is encoded under the custom0 opcode:

0000001 00000 XXXXX 000 000XX 0001011
f7      f5    rs    f3  qd    opcode

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
setq q2, x5	custom0 2, 5, 0, 1
setq q0, x3	custom0 0, 3, 0, 1
setq q3, x1	custom0 3, 1, 0, 1

retirq

Return from interrupt. This instruction copies the value from q0 to the program counter and enables interrupts. The Instruction is encoded under the custom0 opcode:

0000010 00000 00000 000 00000 0001011
f7      f5    rs    f3  rd    opcode

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
retirq	custom0 0, 0, 0, 2

maskirq

Enable/disable interrupt sources. The Instruction is encoded under the custom0 opcode:

0000011 XXXXX 00000 000 00000 0001011
f7      f5    rs    f3  rd    opcode

The following interrupt sources occupy the following bits in the f5 field:

Bit	Interrupt Source
f5[0]	External IRQ
f5[1]	Timer Interrupt
f5[2]	Illegal Instruction
f5[3]	Reserved
f5[4]	Reserved

Set bits in the IRQ mask correspond to enabled interrupt sources.

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
maskirq 0	custom0 0, 0, 0, 3
maskirq 1	custom0 0, 0, 1, 3

The processor starts with all interrupts disabled.

An illegal instruction while the illegal instruction interrupt is disabled will cause the processor to halt.

waitirq (unimplemented)

Pause execution until an interrupt triggers. The Instruction is encoded under the custom0 opcode:

0000100 00000 00000 000 00000 0001011
f7      f5    rs    f3  rd    opcode

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
waitirq	custom0 0, 0, 0, 4

timer

Reset the timer counter to a new value. The counter counts down cycles and triggers the timer interrupt when transitioning from 1 to 0. Setting the counter to zero disables the timer.

0000101 00000 XXXXX 000 00000 0001011
f7      f5    rs    f3  rd    opcode

Example assembler code using the custom0 mnemonic:

Instruction	Assember Code
timer x2	custom0 0, 2, 0, 5

Todos:

• Optional FENCE support
• Optional write-through cache
• Optional support for compressed ISA
• Improved documentation and examples
• Code cleanups and refactoring of main FSM