i2c@f0000800: '#address-cells' is a required property
From schema: Documentation/devicetree/bindings/i2c/litex,i2c.yaml
i2c@f0000800: '#size-cells' is a required property
From schema: Documentation/devicetree/bindings/i2c/litex,i2c.yaml
Fix this by adding the missing properties.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
gpio@f0003000: 'gpio-controller' is a required property
From schema: Documentation/devicetree/bindings/gpio/litex,gpio.yaml
gpio@f0003000: '#gpio-cells' is a required property
From schema: Documentation/devicetree/bindings/gpio/litex,gpio.yaml
Fix this by adding the missing properties.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
mmc@f0006800:reg:0: [4026558464, 256, 4026560512, 256, 4026562560, 256, 4026564608, 256] is too long
From schema: dt-schema/dtschema/schemas/simple-bus.yaml
mmc@f0006800:reg:0: [4026558464, 256, 4026560512, 256, 4026562560, 256, 4026564608, 256] is too long
From schema: dt-schema/dtschema/schemas/reg.yaml
Fix this by grouping the tuples in the "reg" property using angle
brackets.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
serial@f0001000: 'device_type' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/serial/litex,liteuart.yaml
Fix this by dropping the offending property.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
interrupt-controller@f0c00000: compatible:0: 'sifive,plic-1.0.0' is not one of ['sifive,fu540-c000-plic', 'canaan,k210-plic']
From schema: Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
interrupt-controller@f0c00000: compatible:1: 'sifive,plic-1.0.0' was expected
From schema: Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
interrupt-controller@f0c00000: '#address-cells' is a required property
From schema: Documentation/devicetree/bindings/interrupt-controller/sifive,plic-1.0.0.yaml
Fix this by correcting the order of the compatible values, and adding
the missing #address-cells property.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Assuming "#[address|size]-cells = <1>", both of the following are
equivalent:
reg = <start1 size1>, <start2 size2>, ..., <startN sizeN>;
reg = <start1 size1 start2 size2 ... startN sizeN>;
The second form appears more widely used and popular, including in
the output of json2dts.py, with the exception of the mac0 node, which
uses the first form. This patch makes output generated for mac0
consistent with that for other DT nodes.
Un-allocated CSRs were already automatically detected so when un-allocated we can just
simply allocate them automatically instead of raising an error. This also allows
simplifying user's code since self.csr.add/self.add_csr will no longer be required.
Geert Uytterhoeven
Shawn Hoffman
Florent Kermarrec
Gabriel Somlo
Dolu1990
Jędrzej Boczar