9ae224a2a7
sipeed_tang_primer_25k: new board
2023-10-17 07:45:40 +02:00
842819d832
platforms/xilinx_zcu102: Add pin definitions for DDR4 SDRAM and FMC connectors.
2023-10-13 23:53:10 +09:00
371234b369
platforms/analog_pocket: Add Video Scaler pins definitions and output_term/current strength on SDRAM pins.
...
From https://github.com/tpwrules/pocket_linux .
2023-10-09 10:12:38 +02:00
149ed9630c
platforms/ocp_tap_timecard: Add with_multiboot parameter to enable/disable multiboot images generation.
...
Generating multiboot images is not very fast, disabling it for quick P&R iterations can be useful.
2023-10-03 19:03:42 +02:00
aa853d5a48
platforms/efinix_trion_t20_bga256_dev_kit: CON4 cleanup
2023-10-02 19:19:50 +02:00
bc6f6d869e
platforms/efinix_trion_t20_bga256_dev_kit: CON3 (LVDS RX) / CON4 (LVDS TX)
2023-10-02 18:51:53 +02:00
6f0cd56109
update to match zcu102 constraint spec
2023-09-28 11:11:21 +02:00
928c1a2539
platforms/sipeed_tang_mega_138k: Fix default_clk_name/period.
2023-09-26 21:07:21 +02:00
29018a8382
Merge pull request #523 from Icenowy/tangmega138k
...
[RFC] sipeed_tang_mega_138k: new board
2023-09-26 19:12:44 +02:00
5f8ac853b1
Resolve High Density bank IOStandard error
...
This resolves the following error during `build` on Vivado 2023.1:
```ERROR: [DRC BIVB-1] Bank IO standard Support: Bank 47 has incompatible IO(s) because: The LVDS I/O standard is not supported for banks of type High Density. Move the following ports or change their properties:
clk125_p```
2023-09-25 12:50:30 +02:00
1fb317840f
platforms/ocp_tap_timecard: Add clk10 and som_led.
2023-09-22 08:33:04 +02:00
c14d66cb6b
analog_pocket: Add Serial (to fix CI) and add to board list.
2023-09-21 10:11:55 +02:00
3df677cfeb
Add initial Analog Pocket platform/target with Clk/SDRAM, able to run a simple SoC with SDRAM over JTAG-UART.
...
$ ./analog_pocket.py --uart-name=jtag_uart --build --load
$ litex_term jtag --jtag-config=openocd_usb_blaster.cfg
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2023 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS built on Sep 21 2023 08:53:57
BIOS CRC passed (1e2b3f44)
LiteX git sha1: 7d738737
--=============== SoC ==================--
CPU: VexRiscv @ 50MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 128.0KiB
SRAM: 8.0KiB
L2: 8.0KiB
SDRAM: 64.0MiB 16-bit @ 50MT/s (CL-2 CWL-2)
MAIN-RAM: 64.0MiB
--========== Initialization ============--
Initializing SDRAM @0x40000000...
Switching SDRAM to software control.
Switching SDRAM to hardware control.
Memtest at 0x40000000 (2.0MiB)...
Write: 0x40000000-0x40200000 2.0MiB
Read: 0x40000000-0x40200000 2.0MiB
Memtest OK
Memspeed at 0x40000000 (Sequential, 2.0MiB)...
Write speed: 15.6MiB/s
Read speed: 22.1MiB/s
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex>
2023-09-21 09:19:57 +02:00
a0b7811c54
platforms/ti60_f225: Add n parameter to rgmii_ethernet_qse_ios to allow having multiple adapters.
2023-09-11 10:45:28 +02:00
b92c96b3a4
colorlight_i9plus: Cosmetic cleanups.
2023-08-30 17:22:11 +02:00
3471617878
Merge pull request #502 from chmousset/add_colorlight_i9plus
...
[init] added colorlight i9+ based on XC7A50 FPGA
2023-08-30 16:54:26 +02:00
4862d0667c
Merge pull request #515 from josuah/crosslink_nx_openocd
...
Allow use of OpenOCD for the Crosslink-NX
2023-08-28 16:35:20 +02:00
5799c35247
platforms/gsd_orangecrab: Set alt point to DFUProg.
2023-08-28 16:28:04 +02:00
ebfb9b8e01
sipeed_tang_mega_138k: new board
...
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2023-08-15 16:33:13 +08:00
8172a304b3
platforms/crosslink_nx_evn: allow use of OpenOCD
2023-08-08 23:25:41 +02:00
3903cdee92
Merge pull request #517 from bayi/master
...
Digilent CMOD A7 ISSIRAM fix
2023-08-08 19:29:32 +02:00
a6b025f7f3
Fix Digilent Cmod A7 ISSIRAM reading
2023-08-05 19:56:15 +02:00
5412d0e0e9
platforms/crosslink_nx_evn: allow use of UARTBone
...
This goes along a small resistor jumper modification and firmware flashing like
it is for the ECP5 board. A warning message is added as the default serial might
be affected (--serial serial by default). The FTDI modification software used
for the ECP5 seems to be requried and matching.
This can be tested this way:
targets/lattice_crosslink_nx_evn.py --csr-csv=csr.csv --toolchain=oxide --programmer=openocd --uart-name crossover+uartbone --build --load
litex_server --uart --uart-port /dev/ttyUSB1
litex_cli --regs
2023-08-04 20:47:32 +02:00
efc15a91a9
global: Use new WaitTimer integrated cast to int.
2023-08-01 14:56:35 +02:00
ace789653f
platforms/ti60_f225: Add connector numbering to ease review/schematic comparison.
2023-07-21 09:08:22 +02:00
72a951081a
xu8_pe3: Fix clk_p/n on pcie_x8.
2023-07-13 18:10:46 +02:00
18a3909a9c
global: Switch to litex.gen.genlib.misc.
2023-07-06 22:11:45 +02:00
e9335cd67a
Fix pins in Alchitry Cu platform, add target for Alchitry Cu
2023-06-27 21:35:55 +05:30
061a768495
Add Alchitry Cu board
2023-06-16 21:36:57 +05:30
c49a50a934
platform/gsd_butterstick: Add mssing USB comment.
2023-06-16 09:10:47 +02:00
28ecb1e9f3
enclustra_mercury_xu8_pe3: Fix pcie_x8 and add GTH banks for pcie_x4/x8.
2023-06-15 17:57:38 +02:00
06e8829eb4
platforms/gsd_butterstick: Add default programmer to avoid breaking older designs.
2023-06-14 16:40:35 +02:00
96175a9986
sitlinv_stlv7325_v2: Add default value to vccio.
2023-06-07 15:00:49 +02:00
765ee1a3ce
sitlinv_stlv7325_v2: VCCIO jumper default factory setting is 3.3V
2023-06-07 10:12:55 +07:00
b01abce7d5
platform/stlv7325-v2: update VCCIO to fix --with-pcie generation
2023-06-01 16:45:33 -04:00
7fc8ca9816
Merge pull request #506 from sensille/rv901t-spiflash
...
Add spiflash definition to linsn_rv901t board
2023-05-30 22:36:14 +02:00
8a263c18f2
sitlinv_stlv7325: Rename to v1 and update VCCIO to fix --with-pcie generation.
2023-05-30 10:39:20 +02:00
4a05e56058
Add spiflash definition to linsn_rv901t board
2023-05-27 16:20:32 +02:00
2ae2dfa6a3
Add vcu128 target ( #497 )
...
Add initial VCU128 support.
2023-05-25 22:25:44 +02:00
9362e589ac
Add initial Enclustra XU8/PE3 platform definition with Clk/I2C/PCIe/DDR4 and FMC connector definition.
2023-05-25 10:01:19 +02:00
550bc0eee5
add QMTech XC7K325T board, add seven segment display to daughterboard
2023-05-08 11:51:51 +07:00
187080228c
add qmtech_xc7l325t
2023-05-08 05:17:35 +07:00
d33cf1a74c
mnt_rkx7: Cosmetic cleanups.
2023-05-05 09:48:06 +02:00
6144966d24
Merge pull request #501 from mntmn/master
...
mnt_rkx7: RGB and USB fix, add HDMI terminal
2023-05-05 09:37:40 +02:00
31c680abf8
[enh] added option for uartbone
2023-04-30 09:42:31 +02:00
874532871f
[enh] taking advantage of pins directly connected
2023-04-30 09:24:49 +02:00
1202c387bf
[init] added colorlight i5a-907 support
2023-04-30 09:24:46 +02:00
322cc5d45b
[init] added colorlight i9+ based on XC7A50 FPGA
2023-04-29 18:36:35 +02:00
1185ff51f1
Initial support for STLV7325 (v2) Kintex-7 board.
...
This is the 2nd (2023) version of the board sold through
https://www.aliexpress.us/item/3256801088848039.html
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
2023-04-28 10:24:21 -04:00
a9e3e3c050
Merge branch 'master' of https://github.com/litex-hub/litex-boards
2023-04-25 20:29:11 +02:00
Gwenhael Goavec-Merou
rniwase
Florent Kermarrec
Gwenhael Goavec-Merou
Liana Koleva
Icenowy Zheng
Josuah Demangeon
Bayi
Mark1626
Hans Baier
Gabriel Somlo
Arne Jansen
Chen
Charles-Henri Mousset
Lukas F. Hartmann