8172a304b3
platforms/crosslink_nx_evn: allow use of OpenOCD
2023-08-08 23:25:41 +02:00
3903cdee92
Merge pull request #517 from bayi/master
...
Digilent CMOD A7 ISSIRAM fix
2023-08-08 19:29:32 +02:00
a6b025f7f3
Fix Digilent Cmod A7 ISSIRAM reading
2023-08-05 19:56:15 +02:00
5412d0e0e9
platforms/crosslink_nx_evn: allow use of UARTBone
...
This goes along a small resistor jumper modification and firmware flashing like
it is for the ECP5 board. A warning message is added as the default serial might
be affected (--serial serial by default). The FTDI modification software used
for the ECP5 seems to be requried and matching.
This can be tested this way:
targets/lattice_crosslink_nx_evn.py --csr-csv=csr.csv --toolchain=oxide --programmer=openocd --uart-name crossover+uartbone --build --load
litex_server --uart --uart-port /dev/ttyUSB1
litex_cli --regs
2023-08-04 20:47:32 +02:00
efc15a91a9
global: Use new WaitTimer integrated cast to int.
2023-08-01 14:56:35 +02:00
ace789653f
platforms/ti60_f225: Add connector numbering to ease review/schematic comparison.
2023-07-21 09:08:22 +02:00
72a951081a
xu8_pe3: Fix clk_p/n on pcie_x8.
2023-07-13 18:10:46 +02:00
18a3909a9c
global: Switch to litex.gen.genlib.misc.
2023-07-06 22:11:45 +02:00
e9335cd67a
Fix pins in Alchitry Cu platform, add target for Alchitry Cu
2023-06-27 21:35:55 +05:30
061a768495
Add Alchitry Cu board
2023-06-16 21:36:57 +05:30
c49a50a934
platform/gsd_butterstick: Add mssing USB comment.
2023-06-16 09:10:47 +02:00
28ecb1e9f3
enclustra_mercury_xu8_pe3: Fix pcie_x8 and add GTH banks for pcie_x4/x8.
2023-06-15 17:57:38 +02:00
06e8829eb4
platforms/gsd_butterstick: Add default programmer to avoid breaking older designs.
2023-06-14 16:40:35 +02:00
96175a9986
sitlinv_stlv7325_v2: Add default value to vccio.
2023-06-07 15:00:49 +02:00
765ee1a3ce
sitlinv_stlv7325_v2: VCCIO jumper default factory setting is 3.3V
2023-06-07 10:12:55 +07:00
b01abce7d5
platform/stlv7325-v2: update VCCIO to fix --with-pcie generation
2023-06-01 16:45:33 -04:00
7fc8ca9816
Merge pull request #506 from sensille/rv901t-spiflash
...
Add spiflash definition to linsn_rv901t board
2023-05-30 22:36:14 +02:00
8a263c18f2
sitlinv_stlv7325: Rename to v1 and update VCCIO to fix --with-pcie generation.
2023-05-30 10:39:20 +02:00
4a05e56058
Add spiflash definition to linsn_rv901t board
2023-05-27 16:20:32 +02:00
2ae2dfa6a3
Add vcu128 target ( #497 )
...
Add initial VCU128 support.
2023-05-25 22:25:44 +02:00
9362e589ac
Add initial Enclustra XU8/PE3 platform definition with Clk/I2C/PCIe/DDR4 and FMC connector definition.
2023-05-25 10:01:19 +02:00
550bc0eee5
add QMTech XC7K325T board, add seven segment display to daughterboard
2023-05-08 11:51:51 +07:00
187080228c
add qmtech_xc7l325t
2023-05-08 05:17:35 +07:00
d33cf1a74c
mnt_rkx7: Cosmetic cleanups.
2023-05-05 09:48:06 +02:00
6144966d24
Merge pull request #501 from mntmn/master
...
mnt_rkx7: RGB and USB fix, add HDMI terminal
2023-05-05 09:37:40 +02:00
31c680abf8
[enh] added option for uartbone
2023-04-30 09:42:31 +02:00
874532871f
[enh] taking advantage of pins directly connected
2023-04-30 09:24:49 +02:00
1202c387bf
[init] added colorlight i5a-907 support
2023-04-30 09:24:46 +02:00
322cc5d45b
[init] added colorlight i9+ based on XC7A50 FPGA
2023-04-29 18:36:35 +02:00
1185ff51f1
Initial support for STLV7325 (v2) Kintex-7 board.
...
This is the 2nd (2023) version of the board sold through
https://www.aliexpress.us/item/3256801088848039.html
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
2023-04-28 10:24:21 -04:00
a9e3e3c050
Merge branch 'master' of https://github.com/litex-hub/litex-boards
2023-04-25 20:29:11 +02:00
d160a5ad5d
mnt_rkx7: swap RGB red/blue channels
2023-04-25 20:28:16 +02:00
03913e2e15
Update terasic_de10nano.py
...
Corrected pin number
2023-04-23 22:28:00 -05:00
b8cb2eaa47
Merge pull request #493 from hansfbaier/deca-ddr3
...
make DDR3 memory work on the DECA with the UniPHY
2023-04-11 15:27:02 +02:00
60ac45e80c
make DDR3 memory work on the DECA with the UniPHY
2023-04-11 19:59:49 +07:00
e120b77ef0
enclustra kx2/st1: fix connectors
2023-04-11 10:58:52 +07:00
c7077880b9
copyright notices on enclustra
2023-04-11 10:29:52 +07:00
ed947d1b55
enclustra: add baseboard ST1
2023-04-11 10:29:44 +07:00
be8ee26b2c
enclustra_mercury_kx2: Add ST1 baseboard, part 1
2023-04-11 05:39:11 +07:00
58679262ad
enclustra kx2: add connectors
2023-04-10 14:06:42 +07:00
a8eb0b20c1
Merge pull request #491 from hansfbaier/stlv7325-hdmi
...
STL7325: Add Video, and connectors (FMC, BTB, 2.54mm)
2023-04-07 09:06:55 +02:00
52ca60c2ac
stlv7325: fix HDMI io standard
2023-04-07 09:50:04 +07:00
2f13decc49
stlv7325: make VCCIO configurable
2023-04-07 09:27:03 +07:00
abd639ba9e
stlv7325: add 2.54mm headers
2023-04-07 08:21:17 +07:00
3f85e4ae62
stlv7325: add BTB connectors
2023-04-07 08:09:27 +07:00
b3e44324d1
sitlinv_stlv7325: add FMC connector
2023-04-07 07:56:27 +07:00
5067a2683f
sitlinv_stlv7325: add video HDMI, enable compressed bitstream
2023-04-07 07:31:42 +07:00
43ce24dcb3
add QMTech 5CEFA5 Cyclone V board support
2023-04-06 18:27:51 +07:00
ae3d5d599b
sqrl_fk33: Remove es1 workaround now that recent version of Vivado support it non-es devices.
2023-04-04 18:11:38 +02:00
e11d40a249
Merge pull request #487 from ICE-V-Wireless/master
...
Add PMOD registrations to ICE-V Wireless
2023-04-02 11:44:02 +02:00
5de47baa44
Add PMOD registrations to ICE-V Wireless
...
Signed-off-by: Michael Welling <mwelling@ieee.org>
2023-04-02 03:31:55 -05:00
f564f80826
terasic_deca: hdmi i2s uses 1.8V, not 3.3V
2023-04-01 08:14:09 +07:00
74c8569a5c
DDR3 RAM works on 1.5V, not 1.35V
2023-03-27 15:17:42 +07:00
40c8e62b09
use bistream compression on those large devices
2023-03-21 09:25:56 +07:00
0125ae4271
Add support for QMTech Artix7 200T FBG484 board
2023-03-20 08:21:36 +07:00
98ddb97f5e
Support QMTech XC7A75T, XC7A100T core boards
2023-03-20 07:57:58 +07:00
6b8a5d35c0
sipeed_tang_nano_20k: support copackaged SDRAM
...
The copackaged SDRAM of GW2AR-18 QN88 package is 8MB size, 32bit DQ
width.
Add support for it.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2023-03-13 17:11:06 +08:00
291c43b898
sipeed_tang_nano_20k: new board
...
This board uses Gowin GW2AR series chip (which is GW2A with integrated
RAM).
Support for the integrated SDRAM on Tang Nano 20K is still TODO.
Note: currently when the SD card is enabled, block 0 could be correctly
read but block 1 will fail.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2023-03-13 16:45:25 +08:00
28a1aefc21
Update sipeed_tang_nano_9k.py
...
add pin info for _connectors
2023-03-09 17:57:39 +01:00
1df46d1571
platforms/sipeed_tang_nano_9k: Review SPI RGB LCD addition.
2023-03-06 09:03:12 +01:00
8d35591f47
Update sipeed_tang_nano_9k.py
...
add SPI-Interface for the 1.14inch LCD
2023-03-04 15:25:59 +01:00
943cf2636f
platforms/sipeed_tang_primer_20k: Add checkme on leds IOstandard.
2023-03-02 12:14:04 +01:00
9e73ba53ea
platforms/sipeed_tang_primer_20k: Update hdmi pins to official dock version and fix compilation.
...
Test:
./sipeed_tang_primer_20k.py --cpu-type=serv --with-video-terminal --build --load
Working.
2023-03-02 11:39:41 +01:00
47659835b0
platforms: Switch US/USP platforms to XilinxUS/USPPlatform.
...
We were still using Xilinx7SeriesPlatform.
2023-03-01 09:37:55 +01:00
8a6f0bd94f
opalkelly_xem8320: Review and update to recent LiteX changes.
2023-03-01 09:16:51 +01:00
e20391d366
Basic SoC for Opal Kelly XEM8320
2023-02-28 13:19:12 -07:00
33cfe59614
add pullups for kopflos ethernet
2023-02-22 08:00:58 +01:00
bd20b31a5c
add support for machdyne kopflos board
2023-02-21 11:18:22 +01:00
b1df2c0f85
Add initial support for the ICE-V wireless
...
Signed-off-by: Michael Welling <mwelling@ieee.org>
2023-02-19 00:00:07 -06:00
7b716e4899
antmicro_sdi_mipi_video_converter: Cleanup/Update to new LiteX conventions.
2023-02-16 09:02:14 +01:00
fe2be83feb
Merge pull request #473 from antmicro/crosslink-nx-zephyr
...
Add support for SDI-MIPI Video Converter
2023-02-16 08:49:04 +01:00
857166e455
xilinx_alveo_u200: Add missing copyrights.
2023-02-16 08:45:34 +01:00
adf8b8c5df
Merge pull request #472 from vietthanh85/xilinx_alveo_u200
...
Add support for Xilinx Alveo U200
2023-02-16 08:42:21 +01:00
31d718749a
Add copyrights
2023-02-15 12:37:33 +01:00
70f2fd6368
Fix format
2023-02-15 12:37:33 +01:00
0c774a906d
Add clk12 to platform
2023-02-15 12:37:33 +01:00
223a69cf91
Add platform and target files for Antmicro's sdi mipi video converter board
...
Signed-off-by: Tomasz Michalak <tmichalak@antmicro.com>
2023-02-15 12:37:33 +01:00
ec7a5c4c0b
Correct DDR4 IO Banks of Xilinx Alveo U200
2023-02-14 06:40:12 +07:00
fdffeb8474
radiona_ulx4m_ld_v2: Do a first review/cleanup path.
2023-02-13 16:11:32 +01:00
99db2ae60d
Delete ulx4m_ld_v2.py
2023-02-13 11:48:51 +01:00
57c9cff39e
Update radiona_ulx4m_ld_v2.py
2023-02-13 11:45:48 +01:00
9320ae8b74
Fixing platform file
2023-02-13 11:44:59 +01:00
a3815efccb
Adding radiona ULX4M-LD-V2
2023-02-11 16:57:34 +01:00
a354f04143
avoid undefined clocks by moving the derive*-statements to start of the additional constraints list
2023-02-09 15:58:41 +01:00
b9874685a5
gadgetfactory_papilio_pro: Cosmetic cleanups.
2023-01-17 15:43:12 +01:00
ec4d203eb6
Merge pull request #471 from Acathla-fr/papilio
...
Target/Platform Papilio Pro added (with Arcade MegaWing)
2023-01-17 11:21:27 +01:00
801008f5ad
Merge pull request #469 from hansfbaier/hpcstore-rename
...
HPC FPGA Store on AliExpress renamed itself to SITLINV
2023-01-17 11:20:19 +01:00
3b36e576ba
Add support for Xilinx Alveo U200
2023-01-17 06:44:21 +07:00
05ef1ee09e
Target/Platform Papilio Pro added (with Arcade MegaWing)
2023-01-16 13:41:24 +01:00
55fcb4cd47
xilinx_alveo_u2x0: Improve indentation on DRAMs.
2023-01-16 09:34:59 +01:00
be77f82720
platforms/xilinx_alveo_u250: Fix dram numbering.
2023-01-16 09:31:23 +01:00
e02f64a7db
platforms/gsd_butterstick: Fix copyright.
2023-01-16 08:41:10 +01:00
59a897e2dd
gsd_butterstick: Add missing pin defs
2023-01-16 17:32:39 +10:30
c0773ed9b9
HPC FPGA Store on AliExpress renamed itself to SITLINV
2023-01-16 11:31:35 +07:00
36a4100c8b
ocp_timecard: Add DDR3 SDRAM support.
2023-01-13 12:41:34 +01:00
1e35d78512
ocp_tap_timecard: Add initial SMAIOs peripherals to allow using SMA over PCIe DMA or also with direct (and slow) control/visualization with CSR registers.
2023-01-13 10:08:44 +01:00
fc7154a632
ocp_tap_timecard: Add Leds/I2C/PMOD/GPS/SMAs IOs.
2023-01-13 09:14:05 +01:00
a0fd3e7536
Add initial OCP-TAP TimeCard support with PCIe/SPIFlash/Leds/Buttons/DNA/XADC (Compiles but untested).
2023-01-12 18:50:23 +01:00
563ccbd8cf
Merge pull request #464 from machdyne/master
...
initial support for machdyne konfekt and noir
2023-01-01 16:12:51 +01:00
5de6865cbe
Merge pull request #463 from stone3311/master
...
terasic_deca: add SPI SD card support
2023-01-01 16:10:30 +01:00
f0dc9a6874
initial support for machdyne konfekt and noir
2022-12-30 17:00:35 +01:00
6cfb56bb07
terasic_deca: add SPI SD card support
2022-12-28 02:13:06 +01:00
57845d1ca4
Correct pinout and IOStandard
...
Correct connector pinout
Correct pinout for ETH
LED IOStandard set to LVCMOS33
BTN[0] IOStandard set to LVCMOS33
Changes are made based on Tang_primer_20K_3690 and Tang_Primer_20K-Dock_3709 schemes.
2022-12-22 18:30:36 +03:00
a92fdffb35
platforms/digilent_zybo_z7: reorder _io_x & _connectors_x, init cleanup
2022-12-12 22:17:39 +01:00
d28894a4b3
Reintroduce original Zybo + HDMI addition ( #461 )
...
* Reintroduce original Zybo support
* Reintroduce original zybo, add HDMI + fixes for Z7
2022-12-12 22:05:47 +01:00
c05ce32c8a
Merge pull request #458 from trabucayre/arty_s7_tcl_config
...
Arty z7 tcl config
2022-12-08 08:31:22 +01:00
25c40ddda7
add gpio to board
2022-12-05 21:38:56 -03:00
e71e3ab3ec
platforms,targets/digilent_arty_z7: use a dict for PS config instead of fetching file configuration
2022-12-03 16:54:39 +01:00
d0d90e9eef
Merge branch 'litex-hub:master' into master
2022-11-29 15:25:41 -03:00
926ed21f0b
fixed review remarks; added zynq7000 as a submodule for using the ps as a slave
2022-11-23 17:20:25 +01:00
570ea11744
fix(plataform.basys_3): V_sync is pin R19
...
Based in https://github.com/Digilent/digilent-xdc/blob/master/Basys-3-Master.xdc#LL129C34-L129C37
2022-11-23 09:16:50 -03:00
6f7716adbb
added config for ps7; introduced different variants for the zybo-board; fixed pins
2022-11-18 11:15:54 +01:00
6e10df234f
platforms/decklink_mini_4k: Fix data2_n pin (Thanks @rdolbeau).
2022-11-14 10:21:37 +01:00
3d8106f84d
stlv7325: fix Ethernet IO voltages
...
The IO voltages of Ethernet pins is set to 2.5V instead of 1.5V.
Fix this in the platform definition.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-11-13 17:27:23 +08:00
4ba5793822
sitlinv_stlv7325: remove unexistent COL/CRS pins
...
The COL and CRS pins of the Ethernet PHY is not connected on the board
at all, but assigned dummy positions in the platform definition, which
leads to Vivado warning when building.
Remove these pins from the platform definition.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-11-13 17:27:23 +08:00
24cd983b8c
platforms/alinx_axu2cga: adding missing psu_config at platform level
2022-11-06 21:52:00 +01:00
9960f38d95
targets: replace LiteXSoCArgumentParser by LiteXArgumentParser, remove tasks done LiteXArgumentParser
2022-11-06 11:27:47 +01:00
d7184fb043
stlv7325, a_e115fb: use the proper vendor name Sitlinv
...
The boards are in fact from a vendor called 成都赛特凌威科技有限公司,
and their English registered trademark (used on the banner of their
Taobao store) is Sitlinv, which sounds like 赛特凌威.
Use this vendor name instead of where it's bought.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-10-30 10:51:13 +08:00
6c05ddae1b
Merge pull request #438 from shawnanastasio/nexys4_part_name
...
platforms/nexys4*: Update part name
2022-10-27 12:11:07 +02:00
125569b2cb
add FPGAWars Alhambra II
2022-10-25 21:12:02 +02:00
474dcb5fb3
Merge pull request #436 from Icenowy/isx-im1283
...
Add ISX iM1283 board
2022-10-22 15:56:43 +02:00
d4b2461b5a
platforms/nexys4*: Update part name
...
Symbiflow/f4pga don't recognize the part name xc7a100t-CSG324-1, so
change it to xc7a100tcsg324-1 which works with both f4pga and Vivado.
2022-10-21 14:15:27 -05:00
377cda05a3
ti60_f225_dev_kit: Switch 1.2V banks to 1.8V to fix compilation issues with latest Efinity.
...
Will need to be investigated more.
2022-10-20 18:21:52 +02:00
745ebbbfa1
Add ISX iM1283 board
...
ISX iM1283 is a "simple eDP signal generator" which utilizes a XC7A100T
FPGA, and come with a header populated with the FPGA's JTAG.
This commit adds initial reverse engineered IOs including the DDR3 DRAM
(which cannot work reliably @ DDR3-800, so the system clock is defaultly
set to 80MHz now), two LEDs and SD slot.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-10-14 22:50:43 +08:00
23c6acd013
platforms/ti60_f225_dev_kit: Fix IO voltage conflicts between peripherals/banks.
...
Was already reported as a warning on 2021.1.165.2.19 but now an error with 2022.1.226.
Note: To get the build working with 2022.1.226 the following change had to be done to
pt/bin/writer/pinout.py, line 2254:
- table.add_rows(table_rows)
+ for table_row in table_rows:
+ table.add_row(table_row)
This would need to be investigated more to know if related to our local setup/machine.
2022-10-14 10:22:54 +02:00
3b339ba9a3
platforms/xilinx_kc705: Fix flash proxy name.
2022-10-13 08:48:33 +02:00
99888c52ce
xilinx_kc705/i2c: Add pullups.
2022-10-11 17:26:06 +02:00
3ec18c3583
Add qmtech Cyclone IV Starter Kit
2022-10-09 16:34:44 +02:00
c38b8b1d8c
MNT RKX7: update platform and target for D-2 release
2022-10-03 20:09:48 +02:00
cf416d0d66
stlv7325: Adjust DDR3 pins to match reference design
2022-10-01 11:15:47 +02:00
57eb907210
aliexpress_stlv7325: Fix missing parameter for PULLUP attribute
2022-09-25 23:13:44 +02:00
8c3a5c0608
sipeed_tang_nano_9k: Fix HDMI IOs constraints.
2022-09-23 11:18:30 +02:00
9dbee62eac
add option to use ecpprog for crosslink-nx eval board
2022-09-15 12:27:08 -07:00
3cef11e04d
platforms/newae_cw305: Add sma_clk_in/out, buttons, switches and expansion header connector.
2022-09-13 14:26:52 +02:00
f1899954e9
Add initial NewAE CW305 board support.
2022-09-13 12:38:30 +02:00
25c28d2c03
fixed issue with default programmer option
2022-09-10 18:16:04 +01:00
e8504191e3
cleanup
2022-09-10 17:54:43 +01:00
6d0a4c788e
Added DFU support to Butterstick
2022-09-10 17:45:57 +01:00
d39d87b701
sipeed_tang_primer_20k: Switch to PHYPadsReducer and enable the 2 modules.
2022-09-07 12:06:22 +02:00
1663ded641
sipeed_tang_primer_20k: Add initial DDR3 integration (WIP).
2022-09-07 11:53:24 +02:00
abd20f560b
sipeed_tang_primer: Minor cleanups (Rename standard dock to standard, reduce margin on hdmi5x).
2022-09-07 10:56:17 +02:00
4d72c75f49
platforms/sipeed_tang_primer_20k: use replace _connectors.extend by add_connector
2022-09-06 20:19:37 +02:00
74d4a72494
radiona/ulx3s: Rename user_button to user_btn (consistency with other boards) and fix ident.
2022-08-26 22:25:54 +02:00
693cce73bd
Merge pull request #417 from Igor542/master
...
radiona_ulx3s: add buttons
2022-08-26 22:24:05 +02:00
0c14bbf0dc
sipeed_tang_primer_20k: adding dock lite support
2022-08-26 08:43:57 +02:00
9ed3b7baae
radiona_ulx3s: add buttons
2022-08-25 22:19:48 -07:00
94d079f469
sipeed_tang_nano_4k: Fix tab/space.
2022-08-24 16:07:18 +02:00
feff243f8f
Merge pull request #416 from shenki/artix-dc-scm
...
Add Antmicro Artix DC-SCM board
2022-08-24 15:22:52 +02:00
6ba6a7e8fa
Merge pull request #414 from lambdaconcept/master
...
lambdaconcept_ecpix5: fix HDMI pin
2022-08-24 15:14:11 +02:00
f48ed3d9e7
Add Antmicro Artix DC-SCM board
...
Based on commits by:
- Jedrzej Boczar <jboczar@antmicro.com>
- Karol Gugala <kgugala@antmicro.com>
Tested serial and networking on a DC-SCM with mor1k and vexriscv.
2022-08-24 13:03:36 +10:00
c3e99a8419
lambdaconcept_ecpix5: fix HDMI pin
2022-08-11 18:45:10 +02:00
7487440725
Added Tang Nano 4k Support for GoWin Educational IDE v1.9.8.03
2022-08-05 13:28:22 -03:00
6872f7ade6
sipeed_tang_primer_20k: Add LCD pins (untested).
2022-08-05 09:42:38 +02:00
c79d01064e
sipeed_tang_primer_20k: Switch Serial to Dock IOs.
2022-08-05 09:07:20 +02:00
f2cb211432
sipeed_tang_primer_20k: Add buttons and prepare RGB Led.
...
Synthesis issue with WS2812/GowinEDA for now.
2022-08-04 16:32:50 +02:00
09b0c975f3
sipeed_tang_primer_20k: Add Ethernet/Etherbone (compiles but not yet working).
2022-07-26 12:53:42 +02:00
abe08a96aa
sipeed_tang_primer_20k: Add Video (Colorbars), compiles but does not seems to be working.
2022-07-26 12:25:10 +02:00
12b8063941
sipeed_tang_primer_20k: Add LedChaser through 204 pin SODIMM connector/Dock.
2022-07-26 11:44:03 +02:00
d49e43801e
sipeed_tang_primer_20k: Add 204 Pins SODIMM Connector.
...
Will allow defining Dock peripherals.
2022-07-26 11:30:39 +02:00
67ffe095cc
Merge branch 'master' of https://github.com/machdyne/litex-boards
2022-07-15 17:13:22 +02:00
22dcadcfa1
rename ld board prefix to machdyne
2022-07-15 17:13:00 +02:00
9deef65445
Merge branch 'litex-hub:master' into master
2022-07-14 16:02:00 +02:00
52ff93a194
Merge pull request #409 from antmicro/rrozak/remove-dm-pins-from-datacenter
...
Remove DM signals assignment from DDR4 Datacenter platform
2022-07-11 19:34:19 +02:00
2357212161
Remove DM signals assignment from DDR4 Datacenter platform
...
Data Masks (DM) are unsupported on x4 devices and wrong pins were assigned.
Signed-off-by: Ryszard Różak <rrozak@antmicro.com>
2022-07-11 12:29:02 +02:00
3ecec8cd16
Merge branch 'litex-hub:master' into master
2022-07-08 16:59:55 +02:00
756d019571
add support for schoko
2022-07-08 16:58:55 +02:00
6b02ea024a
ti60_f225_dev_kit: Fix ethernet build and enable debug. Now needs testing.
2022-06-28 19:54:00 +02:00
c14611b07c
ti60_f225_dev_kit: Add dummy 0 pin to connectors to use schematic numbering (1-40).
2022-06-27 19:47:19 +02:00
1ad2022138
quicklogic_quickfeather: Move from deprecated Symbiflow to F4PGA
2022-06-17 17:00:48 +02:00
29b72fac7e
taobao_a_e115fb: Minor cleanups.
2022-06-15 11:55:22 +02:00
0ae1417eb5
a_e115fb: Add taobao prefix (Similar to what we do on aliexpress's boards from unknown vendors).
2022-06-15 11:53:11 +02:00
4e0e381f47
Merge pull request #398 from Icenowy/a-e115fb
...
a_e115fb: new board
2022-06-15 11:37:36 +02:00
13fbcbb159
a_e115fb: new board
...
It's a core board with EP4CE115 by a random vendor on Taobao.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-06-13 23:13:29 +08:00
c420429a3c
efinix_ti60_f225: Add the 3 QSE connectors and add RGMII Ethernet QSE extension board.
2022-06-13 16:01:28 +02:00
d37af4aece
Merge pull request #395 from AEW2015/master
...
Support for "discontinued" Avnet aes-ku040-db-g development board
2022-06-07 12:13:47 +02:00
313e758ffe
Updated copywrite and renamed to avnet_aesku40
2022-06-03 20:49:52 -06:00
6e33d9249f
sipeed_tang_primer_20k: Cleanup/Fix.
2022-06-03 11:40:10 +02:00
68733c6e92
Merge pull request #396 from Icenowy/tang20k
...
sipeed_tang_primer_20k: new board
2022-06-03 10:14:55 +02:00
b97d9cd9e8
sipeed_tang_primer_20k: new board
...
Only initial support is added.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
2022-06-03 00:24:20 +08:00
4d98dd38a7
Merge branch 'litex-hub:master' into master
2022-06-01 23:01:43 -06:00
1b96067113
added aesku40 dev board
2022-06-01 22:54:03 -06:00
48353735fa
Merge pull request #393 from swetland/ethernet
...
muselab icesugar pro: add ethernet/etherbone support
2022-05-20 22:10:02 +02:00
5a714167ed
muselab icesugar pro: add ethernet/etherbone support
...
- use P4 header for a waveshare ethernet phy module
- add --with-ethernet, --with-etherbone, --eth-ip, and --eth-dynamic-ip
target configuration options
2022-05-19 14:46:09 -07:00
2214c7baec
enclustra_mercury_kx2: remove useless clk100, because it is not connected to a clock pin
2022-05-20 04:42:06 +07:00
f1e021cbbe
enclustra_mercury_kx2: add clk100, leds, base board serial, DDR3 termination, DDR3 voltage setting
2022-05-19 15:41:44 +07:00
64773b4085
Merge pull request #390 from hansfbaier/hpc-xc7k420t
...
HPC Store xc7k420t
2022-05-16 11:20:15 +02:00
efa5740811
Move HDMI Support From Sipeed Tang Nano 4K.
2022-05-15 10:53:09 +08:00
26c0f546c7
Merge branch 'litex-hub:master' into hpc-xc7k420t
2022-05-14 21:40:12 +07:00
006b54e7ea
Get 3 DDR modules working with Vivado
2022-05-14 21:38:25 +07:00
ee58e5dbc7
Merge pull request #388 from swetland/hdmi
...
muselab: icesugarpro: fix HDMI output
2022-05-12 15:09:03 +02:00
f383ad3938
Support HPC Store XC7K420T board
2022-05-12 12:55:46 +07:00
d1096a2cd0
Add HPC Store XC7K420T board
2022-05-11 08:58:50 +07:00
0ce7f8354c
Add initial LimeSDR Mini V2 support (With SoC + USB3 (FT245PHYSynchronous)).
...
python3 -m litex_boards.targets.limesdr_mini_v2 --csr-csv=csr.csv --build --load
litex_server --jtag --jtag-config=openocd_limesdr_mini_v2.cfg
litex_term crossover
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2022 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS built on May 3 2022 18:59:46
BIOS CRC passed (5f29afcc)
LiteX git sha1: a4cc859d
--=============== SoC ==================--
CPU: VexRiscv @ 80MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 128KiB
SRAM: 8KiB
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex> ident
Ident: LiteX SoC on LimeSDR-Mini-V2 2022-05-03 18:59:29
2022-05-03 19:04:06 +02:00
ec220e4b5b
muselab: icesugarpro: fix HDMI output
...
- enable data_n outputs
- use drive_both property of updated VideoHDMIPHY to drive both
differential outputs
- adjust default clocking to successfully close timing
(sysclk at 50Mhz, HDMI at 25MHz, HDMIx5 at 125MHz)
2022-05-03 04:04:26 -07:00
3ebc9877ad
1bitsquared_icebreaker: Rename to icebreaker (Python does not like number as prefix for imports).
2022-05-02 13:20:40 +02:00
9914478854
xilinx_ac701: Add SPI-Flash support.
2022-04-28 11:05:51 +02:00
ae8bdb74a9
xilinx_kc705: Add SPI-Flash support.
2022-04-28 10:27:54 +02:00
68ea5fe057
platforms/colorlight_5a_75b/v7_0: Comment rst_n to avoid deadlock on reboot command.
2022-04-25 18:50:17 +02:00
39a314cdae
Rename aliexpress_u420t to aliexpress_xc7k420t.
2022-04-21 14:28:26 +02:00
06396a2cb6
Merge pull request #384 from hansfbaier/qmtech-ep4cgx150
...
add board support for QMTech EP4CGX150
2022-04-21 10:36:51 +02:00
Josuah Demangeon
enjoy-digital
Bayi
Mark1626
Hans Baier
Gabriel Somlo
Arne Jansen
Chen
Charles-Henri Mousset
Lukas F. Hartmann
594rk
Michael Welling
Icenowy Zheng
Marco
AEW2015
inc
Antoni Pokusinski
Tomasz Michalak
Do Viet Thanh
Goran Mahovlic
MV
Fabien
Greg Davill
stone3311
jiv4ik
Gwenhael Goavec-Merou
JoyBed
Guilherme Salustiano
Guilherme Salustiano
mkuhn99
Chema
Shawn Anastasio
Franck Jullien
Vadzim Dambrouski
slagernate
Adam Zeloof
Igor Safonov
Joel Stanley
Pierre-Olivier Vauboin
Chandler Klüser
Machdyne
Ryszard Różak
Robert Szczepanski
Brian Swetland
minexo79