0ceb15938f
digilent_arty_z7: Remove fake serial.
2022-03-01 11:05:59 +01:00
673676e3cb
digilent_arty_a7: Switch to VivadoProgrammer.
2022-03-01 10:48:22 +01:00
e16e5e0591
digilent_arty_z7: Fix add_period_constraint.
2022-03-01 10:30:14 +01:00
1320f3bd23
Merge pull request #357 from DaveBerkeley/colorlight_i9
...
Add ColorLight i9 v7.2
2022-03-01 10:07:55 +01:00
a19c03fa55
targets: Switch to generic/portable HyperRAM core from LiteX.
2022-03-01 09:10:19 +01:00
c9d009c735
Add ColorLight i9 v7.2
2022-02-28 14:08:49 +00:00
11dfe225fa
Merge pull request #356 from fjullien/add_mipi_tx
...
efinix: add MIPI TX to platform Ti60
2022-02-25 16:53:11 +01:00
c54e92c47d
efinix: add MIPI TX to platform Ti60
2022-02-25 15:15:14 +01:00
2311db18f8
add initial support for kröte fpga board
2022-02-25 14:22:19 +01:00
1623ba5942
targets/stlv7325: Reduce sys_clk_freq to 100MHz.
...
See https://github.com/enjoy-digital/litedram/issues/285 .
2022-02-25 09:04:07 +01:00
872113e1cc
stlv7325: Add SDCard support.
2022-02-24 18:02:43 +01:00
a08f346d90
stlv7325: Add Etherbone support (untested).
2022-02-24 17:43:53 +01:00
b1550f006a
stlv3225: Minor Review/Cleanup, switch to JTAG HS2 programmer.
2022-02-24 17:17:08 +01:00
174d958ca7
Initial support for STLV7325 Kintex-7 board.
2022-02-23 18:28:55 +01:00
6661947d96
Merge pull request #354 from madscientist159/master
...
Add initial support for RCS Arctic Tern boards
2022-02-23 18:06:08 +01:00
1717af68ac
targets/sqrl_acorn/ddr3: Disable write_latency_calibration.
...
Introduce some memtest failures on some boards.
2022-02-23 10:38:43 +01:00
ae4b3c0938
Add initial support for RCS Arctic Tern boards
2022-02-21 20:04:51 -06:00
85397818d9
add Xilinx ZCU216 support
2022-02-21 19:14:13 +01:00
7d84e6e863
efinix_titanium_ti60_t225: Add SPI/Native SDCard support.
...
Both modes working with 8559b88ad8
2022-02-21 10:35:06 +01:00
df36cdbcc9
siglent_sds1104xe: Switch back to native DRAM width (now possible with Nax).
2022-02-18 11:47:08 +01:00
d85f88f42a
siglent_sds1104xe: Reduce DRAM's width to 16-bit for now (to use NaxRiscv).
2022-02-16 17:59:40 +01:00
08a79fa3ac
lattice_ecp5_vip: Minor cleanups, fix CI.
2022-02-15 10:58:38 +01:00
30afe26669
Merge pull request #348 from hubmartin/ecp5-vip
...
Draft: Add Lattice ECP5 VIP board + HDMI output board support
2022-02-15 08:53:57 +01:00
896884dd21
Merge branch 'master' into axu2cga_software
2022-02-15 08:21:29 +01:00
6bbf8c8268
Merge pull request #351 from sergachev/litex_baseboard_openocd
...
add openocd config for litex acorn baseboard
2022-02-15 08:11:41 +01:00
3f58df9974
platforms/targets: Fix typos.
2022-02-14 17:26:46 +01:00
b53b79821e
platforms: Expose toolchain parameter on all platforms to ease switching to alternative/open-source toolchains.
2022-02-14 11:35:18 +01:00
12b91eccdc
digilent_arty: Remove yosys+nextpnr INTERNAL_VREF constraint skip (now directly done in LiteX).
2022-02-14 10:45:29 +01:00
5cd1d7eaec
add openocd config for litex acorn baseboard
2022-02-13 16:44:40 +01:00
5eca41ac73
targets/alinx_axu2cga: adding PS software support (inspired by xilinx_kv260)
2022-02-12 18:24:01 +01:00
50654f1b7b
platforms/alinx_axu2cga: add zynqmp PS configuration params
2022-02-12 18:19:55 +01:00
d672d9a9b1
targets: s/alinx_axu2gca/alinx_axu2cga/gc
2022-02-12 18:12:45 +01:00
c2cd4410df
Code cleanup, add copyright
...
Signed-off-by: hubmartin <hub.martin@gmail.com>
2022-02-12 17:50:07 +01:00
c0e671919d
sqrl_acorn: Downgrade to SATA Gen1 for now (allow lower sys_clk_freq and enough for current tests).
2022-02-09 19:10:12 +01:00
d9b77c6f25
digilent_arty: Add --flash support.
2022-02-09 17:51:56 +01:00
4894926c40
xilinx_kv260: +x.
2022-02-09 16:01:51 +01:00
27b03df886
Add Lattice ECP5 VIP board + HDMI output board support
2022-02-08 21:47:58 +01:00
450a26f395
Merge branch 'master' of https://github.com/litex-hub/litex-boards
2022-02-08 12:55:09 -05:00
7ed633dc4b
add guideline for serial interface
2022-02-08 12:54:34 -05:00
5a0f69502b
enable use of HBM for linux boot
2022-02-08 12:18:38 -05:00
5d52bc5461
Fix seven_seg pin assignment in DE1-SoC
...
Fixes quartus build error:
```
Error (171016): Can't place node "seven_seg5[6]" -- illegal location assignment PIN_AA2 File: /home/arusekk/src/fpga-proj/build/de1soc/gateware/de1soc.v Line: 49
```
2022-02-08 09:03:53 +01:00
18e8bec9d4
xilinx/kv260: Minor cleanup and add Build/Use instructions (from PR).
2022-02-07 08:12:43 +01:00
8621700916
Merge pull request #345 from sergachev/feature/xilinx_kv260
...
Add Xilinx KV260 support
2022-02-07 07:53:55 +01:00
1d8c3789af
add Xilinx KV260 support
2022-02-06 14:38:57 +01:00
617fa26acd
Add 85F to help for orangecrab device
...
The 85F orangecrab board exists, and works fine when this option is set to 85F, but leaving it out of the help is a bit confusing.
2022-02-06 10:36:58 +00:00
346623fd06
trellisboard: Rename Video I2C to videoi2c.
2022-02-04 09:26:31 +01:00
6d4fe82179
trellisboard: Rename hdmi_i2c to i2c (to have access to i2c_scan in the BIOS).
2022-02-02 11:08:21 +01:00
0522d8b0c5
trellisboard: Update i2c.add_init call.
2022-02-02 10:59:54 +01:00
7f4d464f1b
trellisboard: Add Video Terminal/Framebuffer support and use new I2C init feature to automatically configure TP410 at startup.
2022-02-02 09:52:12 +01:00
4251cfa865
terasic_de0nano: Add Build/Use instructions with JTAG-UART.
2022-02-01 15:58:34 +01:00
4d45611935
targets: Replace JTAG Atlantic (Deprecated) with JTAG-UART.
2022-02-01 11:30:26 +01:00
9144cb44fb
Merge branch 'master' into jev/deca-eth
2022-01-31 16:22:58 +01:00
fbd424fc48
DECA: Add Ethernet and Etherbone support
...
Also fixed pcf_en IO standard compared to golden Arrow project.
2022-01-29 15:15:53 -08:00
9e5224ca49
Add JTAGbone support to Terasic DECA
...
Along the way I added UARTbone support to DECA as well for debugging.
Examples:
./terasic_deca.py --csr-csv csr.csv --with-jtagbone --build --load
litex_server --jtag --jtag-config ../prog/openocd_max10_blaster2.cfg
litex_term crossover
./terasic_deca.py --csr-csv csr.csv --uart-name jtag_uart --build --load
litex_term --jtag-config ../prog/openocd_max10_blaster2.cfg jtag
2022-01-27 14:13:58 -08:00
dd134a4b7d
digilent arty z7: allows toolchain selection (PL only)
2022-01-26 07:30:06 +01:00
74395ca80b
digilent_nexyx_video: Add default toolchain value to CRG (to avoid breaking existing designs).
2022-01-25 16:13:57 +01:00
624572f2e9
alinx_axu2gca: Review and do minor cosmetic changes.
2022-01-25 14:58:47 +01:00
537f04a13d
alinx_axu2gca: new board
...
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
2022-01-25 07:35:42 +01:00
621d45cd9e
digilent_arty: Review and improve CRG to avoid specific yosys+nextpnr code.
...
sys4x/sys4x_dqs/idelay clks can be disabled when integrated-main-ram is used.
2022-01-24 19:16:07 +01:00
c2276c1e6d
Merge pull request #338 from suarezvictor/master
...
Add tweaks to Arty board to support yosys+nextpnr toolchain
2022-01-24 19:02:59 +01:00
1abb03e514
tang_nano_4k: Review/Cleanup:
...
- Revert abstractions on clk_name/period: Too much abstraction to avoid duplications makes the code more difficult to read.
ex:
- When constraining clk27, frequency is already in the name.
- In the target, we want to know we are using clk27 as the main clk.
- We need a default sys_clk_freq for project only importing BaseSoC.
- Revert SPI Flash import (for consistency with other targets).
- Keep VexRiscv as default CPU since this target is able to run it and also for consistency with other targets.
2022-01-24 18:46:51 +01:00
e357eb6d8f
Merge pull request #337 from sergachev/tang_nano_4k_emcu
...
Enable LiteX BIOS on ARM core on Tang nano 4K
2022-01-24 18:36:10 +01:00
cc1b46f106
tang_nano_9k: Fix HyperRAM integration.
2022-01-24 18:35:12 +01:00
db77ea5c7a
Add tweaks to Arty board to support yosys+nextpnr toolchain
2022-01-24 02:06:34 -03:00
f078e55bb1
tang nano 4k: fix removed default_clk_period, fix do_finalize signature
2022-01-23 16:47:20 +01:00
6238052b10
tang nano 4k: disable spi flash with gowin emcu, cleanup
2022-01-23 16:10:46 +01:00
6c81fc708c
tang nano 4k: add memory regions, set default cpu
2022-01-23 13:05:51 +01:00
787f44e7d9
Merge pull request #336 from tcal-x/cmod-a7-flash
...
Digilent CMOD A7: add flash support.
2022-01-23 08:36:49 +01:00
6567af6f49
Digilent CMOD A7: add flash support.
...
Add both "--flash" and "--with-spi-flash"; tested on board.
4MB flash mapped at 0x00400000.
Signed-off-by: Tim Callahan <tcal@google.com>
2022-01-22 18:50:12 -08:00
f533e7f8ba
sipeed_tang_nano_9k: enable copackaged PSRAM
...
Also enable SPI SDCard which was pending by the lack of main_ram
previously.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2022-01-23 03:37:03 +08:00
e35b9b439f
platforms/sipeed_tang_nano_9k: Fix copyrights and remove board diagram/description of the 4k.
2022-01-22 15:55:36 +01:00
999dbd572f
Merge pull request #334 from Icenowy/tang9k
...
sipeed_tang_nano_9k: new board
2022-01-22 15:49:08 +01:00
e699c377a5
sipeed_tang_nano_9k: new board
...
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
2022-01-22 11:45:49 +08:00
e9d4d9066a
xilinx_zcu106: add DDR4 interface and fix reset error
2022-01-22 03:08:21 +08:00
b8aad4b030
Merge pull request #332 from tcal-x/prog-cmod-a7
...
Add openocd programmer for Digilent CMOD A7.
2022-01-21 08:05:22 +01:00
e0c4c0fe39
Add openocd programmer for Digilent CMOD A7.
...
Signed-off-by: Tim Callahan <tcal@google.com>
2022-01-20 20:54:03 -08:00
0e91013fc7
quickfeather: fix path to libeos library when board script called not from its directory; fix wget redownloads; add libeos to gitignore
2022-01-20 18:43:59 +01:00
5f2ccb2d32
targets: Switch from bridge to crossover.
2022-01-19 17:03:17 +01:00
abb54cebb3
trenz_c10lprefkit: Add Etherbone support.
2022-01-19 14:47:14 +01:00
1ce978806d
Merge pull request #328 from sergachev/fix/zedboard_software
...
Fix Zedboard software
2022-01-19 10:05:49 +01:00
f11106e9c5
targets/digilent_cmod_a7: Simplify/Cleanup.
2022-01-19 10:03:20 +01:00
f8e3cc5361
Merge pull request #327 from bl0x/digilent_cmod_a7
...
digilent_cmod_a7: Remove unused clocks.
2022-01-19 09:59:44 +01:00
bbf13f4439
zedboard: remove a hack
2022-01-19 02:41:11 +01:00
4f4d47dcdd
zedboard: correct memory map
2022-01-19 02:40:54 +01:00
fccb952c4b
target: Remove ident_version=True no longer required.
2022-01-18 17:13:02 +01:00
7114911cea
targets: --no-ident-version is now directly provided by LiteX, remove it on targets implementing it.
2022-01-18 16:47:38 +01:00
d92a2b82fb
targets/l2_cache_reverse: Now defaulting to False in LiteX, so setting it to False for correct Framebuffer operations is no longer required.
2022-01-18 11:37:55 +01:00
834125e978
platforms/digilent_nexys_video: add missing CD pin
2022-01-17 17:11:40 -05:00
2c26f07a5a
digilent_cmod_a7: Remove unused clocks.
2022-01-17 22:49:10 +01:00
12fa844b56
decklink_mini_4k: Add dedicated SATA PLL to allow SATA + Framebuffer.
2022-01-17 18:11:52 +01:00
f97e48e4f3
decklink_mini_4k: Add SATA support (over PCIe2SATA).
2022-01-17 14:19:59 +01:00
3e187dea42
quicklogic_quickfeather: Make imports similar to other boards.
2022-01-17 10:00:58 +01:00
99752738b0
Merge pull request #326 from litex-hub/pr322
...
quicklogic_quickfeather: add eos_s3 arm software support library
2022-01-17 09:56:41 +01:00
9984bb8ffb
quicklogic_quickfeather: add eos_s3 arm software support library
2022-01-17 09:47:38 +01:00
73b47e9394
Merge pull request #324 from RobertWilbrandt/arrow_usb_blaster
...
Use Arrow-USB-Blaster for trenz c10lprefkit
2022-01-17 08:47:47 +01:00
06fb73ace3
targets/digilent_nexys_video: Remove SATA Gen3 support (max linerate=3.75Gbps with -1 speedgrade).
2022-01-17 08:45:24 +01:00
ed04e5f95c
Merge pull request #325 from gsomlo/gls-sata-gen
...
targets/digilent_nexys_video: add SATA generation argument
2022-01-17 08:41:29 +01:00
b240c381a7
colorlight_5a_75b: Comment out eth's rst_n (Prevent CPU boot).
2022-01-17 08:30:10 +01:00
6103b3b234
targets/colorlight_5a_75x: List 8.0 in supported revision.
2022-01-17 08:27:19 +01:00
b33deba2ed
platforms: Remove useless symbiflow import.
2022-01-17 08:25:00 +01:00
5c2d85e6a3
targets/digilent_nexys_video: add SATA generation argument
2022-01-16 19:59:36 -05:00
00c9cf1d6e
Use Arrow-USB-Blaster for trenz c10lprefkit
2022-01-16 18:03:40 +01:00
38bff921b2
Fixup.
2022-01-16 13:00:46 +01:00
1077e23e62
digilent_cmod_a7: Also propagate here.
2022-01-16 11:58:14 +01:00
bccbd95526
digilent_cmod_a7: Propagate variant and toolchain
2022-01-16 11:31:08 +01:00
296c99f065
digilent_pynq_z1: Do minor cosmetic cleanups.
2022-01-14 09:39:42 +01:00
45cfe2be6b
qmtech_ecp4ce15/ecp4ce55: Merge in qmtech_ecp4cex5.
...
Defaults to ecp4ce15, ecp4ce55 can be selected with --variant=ecp4ce55.
2022-01-14 09:33:29 +01:00
830757502f
Merge pull request #321 from r4d10n/master
...
Support for Digilent Pynq Z1
2022-01-14 08:48:26 +01:00
a3d168e4c0
HDMI Terminal Support
...
Copyright notice update.
2022-01-13 23:28:43 +05:30
e489c3e3de
Change Serial port to pmoda:0/1
...
Remove usb_uart. Copyright notice update.
2022-01-13 23:24:50 +05:30
e27d49114f
Add initial and minimal ZCU106 support (with Clk/Leds/UART).
2022-01-13 17:40:03 +01:00
ed50c84e0d
Support for Digilent Pynq Z1
2022-01-11 19:33:12 +05:30
bd95ce5e47
Create digilent_pynq_z1.py
2022-01-11 19:31:33 +05:30
c57ea732dd
Added QMTech EP4CE55 board - almost identical to EP4CE15 board but bigger FPGA.
2022-01-07 19:27:40 +00:00
8a33c2aa31
targets: Ensure litex.soc.cores.spi_flash is no longer imported/used.
2022-01-07 19:07:14 +01:00
4b6a9b2cf0
targets/spiflash: Simplify self.cpu.set_reset_address call.
2022-01-07 15:19:23 +01:00
30cacc19c2
efinix_xyloni_dev_kit: Update SPI Flash.
2022-01-07 15:00:39 +01:00
16171282c8
digilent_arty/CRG: Add with_rst parameter to be able to easily disable rst.
...
On Arty, cpu_rst pin is connected to a button but also to USB-UART which also
resets the SoC when USB-UART is connected which is in some case not wanted.
with_rst provides an easy way to disable rst by setting it to False.
2022-01-07 14:12:28 +01:00
3ebbebe750
Merge pull request #319 from antmicro/datacenter-updates
...
antmicro-datacenter updates
2022-01-07 11:03:30 +01:00
8151bf7ffa
targets: Update and simplify SPI-Flash support (Address is now automatically allocated).
2022-01-07 10:34:47 +01:00
a4130556ac
gsd_butterstick: Add optional SYZYGY GPIO (--with-syzygy-gpio) to expose the 32 GPIOs on SYZYGY breakout board.
2022-01-06 18:37:42 +01:00
4ae7b5e4ff
antmicro_datacenter: extend eth reset
2022-01-06 17:40:44 +01:00
86b9b1b56c
antmicro_datacenter: fix clock pin LOC
2022-01-06 17:38:49 +01:00
144c0dc27e
digilent_zedboard: +x.
2022-01-06 09:38:19 +01:00
28cdc8b914
spartan_edge_accelerator: Review/Simplify.
2022-01-06 09:37:46 +01:00
2c6ce12154
spartan_edge_accelerator: Add seeedstudio prefix and seeedsstudio to vendors list.
2022-01-06 09:06:27 +01:00
1ee619a455
Merge pull request #317 from primeshp/spartanacc
...
Spartan Edge Accelerator Board support
2022-01-06 09:03:02 +01:00
6b0bd4da4d
fix(vc707): fix 'dat' typo
2022-01-05 20:02:07 -08:00
db9173ad8b
targets/alchitry_mojo: Fix build.
2022-01-05 18:11:53 +01:00
53dc00eab7
targets/parser: Rely on argparse.ArgumentDefaultsHelpFormatter to provide default in help description.
...
Also do minor adjustments while doing this.
2022-01-05 17:06:40 +01:00
9ad1723ac1
efinix_titanium_ti60_f225_dev_kit: Cleanup HyperRAM IOs.
2022-01-04 15:52:42 +01:00
c836b57145
titanium_ti60_f225_dev_kit: Add HyperRAM separator.
2022-01-04 15:18:26 +01:00
28a6fad705
targets/efinix_titanium_ti60_f225: Defaults to 200MHz clock and increase HyperRam size to 32MB.
2022-01-04 11:25:18 +01:00
f5ac5200ff
Added Spartan Edge Accelerator board
2022-01-03 17:14:54 -05:00
713ae531f6
Add Spartan Edge Accelerator support
2022-01-03 16:31:13 -05:00
059563245d
Merge pull request #314 from sergachev/zedboard
...
LiteX BIOS on Zedboard
2022-01-03 17:59:22 +01:00
c9816f2bc1
snicker_doodle: Add z7-10/z7-20 variants support.
2022-01-03 17:15:27 +01:00
dc61d383e6
snickerdoodle: Rename to krtkl_snicker_doodle and do minor cosmetic changes.
2022-01-03 17:09:17 +01:00
b48d96c40d
Merge pull request #309 from derekmulcahy/master
...
Initial release for Snickerdoodle
2022-01-03 16:46:14 +01:00
fae2cecf93
Merge pull request #315 from hubmartin/master
...
Fix cannot find board 'littlebee'
2022-01-03 16:09:12 +01:00
3dd85d9afb
Merge pull request #313 from fjullien/add_io_to_t120
...
efinix: add clock pins to t120 bga576 platform
2022-01-03 16:07:54 +01:00
064406e2f6
Merge branch 'master' of github.com:hubmartin/litex-boards
2021-12-27 21:08:13 +01:00
b98d76ff39
Fix cannot find board bug
2021-12-27 21:07:16 +01:00
2a6282273f
Merge branch 'litex-hub:master' into master
2021-12-24 22:19:33 -05:00
a118a0e499
Replaced Blinky with LedChaser.
2021-12-24 22:14:18 -05:00
b5008a2d5c
platforms/radiona_ulx3s: Use specific GPDI mapping for 1.7/2.0 revision.
...
Data channels 0/2 are swapped between revisions.
2021-12-23 10:39:58 +01:00
bc3c42ab5f
zedboard: disable soc uart for all variants (zynq does not need it, for soft cpus there are no pins)
2021-12-22 03:28:13 +01:00
53ce00b3fd
zedboard: add target with bios on arm zynq cpu
2021-12-22 03:14:13 +01:00
43a1e13b53
zedboard: compress bitstream, derive default clk f
2021-12-22 03:13:30 +01:00
166451e65e
zedboard: remove fake serial
2021-12-22 03:12:48 +01:00
379745b039
efinix: add clock pins to t120 bga576 platform
2021-12-21 12:34:19 +01:00
154cb672da
Removed unused ext_freq parameter.
2021-12-20 21:42:21 -05:00
81404ff185
Improved PS7 support. Configured external clock.
2021-12-20 21:14:18 -05:00
15ea01197d
Added placeholder clk/led/uart.
2021-12-20 21:12:46 -05:00
d64207f8b6
Merge branch 'litex-hub:master' into master
2021-12-20 17:35:35 -05:00
94b4789286
Merge pull request #312 from trabucayre/arty_z7
...
adding digilent_arty_z7 support
2021-12-20 21:50:41 +01:00
8772190177
Merge pull request #311 from tilk/icesugar_pro
...
Option --with-spi-flash for iCESugar-Pro
2021-12-20 21:49:26 +01:00
8664b59f23
targets: Fix --bios-flash-offset support and other minor cleanups.
2021-12-20 21:41:12 +01:00
c6303480cb
Merge pull request #308 from hubmartin/tinyfpga_bx
...
Fix bios-flash-offset for tinyFPGA
2021-12-20 21:29:37 +01:00
bb92bb00a8
adding digilent_arty_z7 support
2021-12-20 18:02:57 +01:00
4c76e12932
Merge branch 'litex-hub:master' into master
2021-12-20 10:54:09 -05:00
7fb225a162
Option --with-spi-flash for iCESugar-Pro
2021-12-19 15:50:52 +01:00
f18c1a033c
Efinix: ti60: add HyperRAM support
2021-12-17 10:23:10 +01:00
1c87c391c4
Initial release for Snickerdoodle
2021-12-14 16:00:42 -05:00
84f267e00c
Change bios-flash-offset for tinyFPGA
2021-12-14 19:10:03 +01:00
c2a840f777
Merge pull request #307 from fjullien/titanium_spi
...
Titanium spi
2021-12-14 08:21:15 +01:00
9608cae2ee
efinix: Ti60f225 change spi_flash module
2021-12-13 23:01:48 +01:00
be7dbf3b1b
exfinix: efinix_titanium_ti60_f225_dev_kit: fix typo
2021-12-13 22:53:50 +01:00
179e9090d1
Rename efinix_titanium_ti60_bga225_dev_kit to efinix_titanium_ti60_f225_dev_kit and also exclude it from tested platforms/targets.
2021-12-13 15:54:56 +01:00
4a9828c506
Merge pull request #305 from fjullien/efinix_titanium
...
efinix: add titanium Ti60 dev kit
2021-12-13 15:45:55 +01:00
e84f32b918
efinix: add titanium Ti60 dev kit
2021-12-13 09:37:14 +01:00
2df10f278f
platforms/redpitaya: fix DAC pins
2021-12-12 15:55:31 +01:00
35e0026875
Merge pull request #303 from sergachev/master
...
sipeed_tang_nano_4k: add option to build with Gowin EMCU
2021-12-09 14:30:54 +01:00
14a8c50e97
sipeed_tang_nano_4k: connect Gowin EMCU UART, undo unnecessary changes
2021-12-09 00:17:48 +01:00
6274c4c425
sipeed_tang_nano_4k: connect Gowin EMCU UART
2021-12-09 00:12:31 +01:00
13c83ba532
sipeed_tang_nano_4k: add initial Gowin EMCU support
2021-12-08 23:50:14 +01:00
4287ab561e
sipeed_tang_nano_4k: allow non-vexriscv CPUs
2021-12-08 23:33:49 +01:00
338abb4e0c
efinix: add bank voltage configuration to platforms
2021-12-08 18:10:22 +01:00
9119250276
Merge pull request #300 from tilk/de1_soc
...
Better support for DE1-SoC
2021-12-08 06:18:25 +01:00
2b7587632f
Merge pull request #299 from gregdavill/butterstick-updates
...
Butterstick updates
2021-12-08 06:16:29 +01:00
8ad89881c2
fairwaves_xtrx: Add pcie_x2 definitions and switch to it.
2021-12-07 15:27:55 +01:00
df175c5750
efinix_trion_t20_mipi_dev_kit: Add clk26.
2021-12-07 15:27:18 +01:00
59d487f9fb
butterstick: Add pullup on sdcard_cd
2021-12-07 14:32:13 +10:30
cbeb2a3792
Add LedChaser to DE1-SoC
2021-12-05 20:16:10 +01:00
1d5bbb4c7f
Fix loading bitstream for DE1-SoC
2021-12-05 20:16:10 +01:00
90c9696c73
LED, buttons, GPIOs etc. for DE1-SoC
2021-12-05 20:16:00 +01:00
fd2ec534a7
butterstick: Add extra pins
2021-12-05 20:33:28 +10:30
c8a8e943b5
butterstick: add --sdram-device option
...
Set 64M16 as default sdram-device.
Related to #298
2021-12-04 17:07:06 +10:30
61b0dfe63c
butterstick: Add additional SYZYGY connectors
2021-12-04 17:02:36 +10:30
bf8b23c19f
trenz_tec0117: Update target.
2021-12-02 18:23:11 +01:00
efa1f46356
Merge pull request #297 from sergachev/master
...
Fix Sipeed Tang Nano 4k example compilation; adapt Gowin PLL class changes
2021-12-02 09:14:32 +01:00
666ef9dad3
sipeed_tang_nano_4k: use minimal vexriscv variant to fit into number of BSRAMs
2021-11-29 11:46:32 +01:00
2fb734a0f2
sipeed_tang_nano*: adapt Gowin PLL changes in litex
2021-11-29 11:45:13 +01:00
b3175e4a9c
fairwares_xtrx: Generate Fallback/Operational bitstreams.
2021-11-26 16:20:44 +01:00
1829693877
fairwaves_xtrx: Integrate ICAP/SPIFlash (for update over PCIe).
2021-11-26 16:18:52 +01:00
2555fdff91
fairwaves_xtrx: Add SPIFlash, I2C, GPS, I2C, AUX, RF-Switches, RF-IC IOs.
2021-11-26 16:00:07 +01:00
fe14e16c1b
Merge branch 'master' into tang_primer
2021-11-23 19:04:09 +01:00
6954dd25eb
Set minimal core, since full does not work for some reason
2021-11-23 15:26:54 +01:00
b0dcd96964
added comments
2021-11-23 14:58:08 +01:00
0b7fabb864
FireAnt board support
2021-11-23 14:43:52 +01:00
2cc322e65d
Add initial support for Tang Primer board
2021-11-22 19:10:11 +01:00
70c0dbb185
targets/radiona_ulx3s: Remove SDRAM underflows debug pin.
2021-11-22 11:54:18 +01:00
b1817af8a8
Merge pull request #294 from antmicro/fix-ddr4-datacenter-platform
...
platforms: ddr4 datacenter: invert eth clocks
2021-11-21 19:11:13 +01:00
3e9e9bc425
platforms/sqrl_acorn: Add Multiboot Operational/Fallabck bistreams generation.
...
To allow recovery in case of PCIe update failure (Write error, power issue or crash).
2021-11-21 19:10:21 +01:00
60b769b624
efinix_trion_t120_bga576_dev_kit/ethernet: Disable software debug (RX now seems to be working fine).
2021-11-16 18:53:15 +01:00
996f5b2edd
efinix_trion_t120_bga576_dev_kit: Enable target1 port and also connect it to SoC.
2021-11-16 18:12:42 +01:00
7ce6c4cf79
efinix_trion_t120_bga576_dev_kit: Switch to ctrl_type = "none" (Also seems to work fine, avoid ddr_reset_sequencer dependency).
2021-11-16 17:50:47 +01:00
99f4f97f00
efinix_trion_t120_bga576_dev_kit: Use new InterfaceWriterBlock/InterfaceWriterXMLBlock and move PLL/DRAM blocks definition to target.
2021-11-16 17:41:26 +01:00
fa26b126df
platforms: ddr4 datacenter: invert eth clocks
...
Signed-off-by: Alessandro Comodi <acomodi@antmicro.com>
2021-11-16 12:55:50 +01:00
e16fa193fc
qmtech 10cl006: remove all options which won't fit into the device. use uartbone as default
2021-11-15 10:23:01 +07:00
2272962315
qmtech_10cl001: fix wrong sdram clock pin
2021-11-15 09:54:17 +07:00
138dc1467e
quicklogic_quickfeather: Fix build with GPIOIn when cpu-type=None (IRQ not supported).
2021-11-14 09:30:52 +01:00
ed67b91fcc
quicklogic_quickfeather: Simplify cpu_type switch between None/EOS-S3.
2021-11-14 09:26:29 +01:00
2d3422869c
quicklogic_quickfeather: Update clocking.
2021-11-14 09:19:19 +01:00
df468fcf85
quicklogic_quickfeather: Avoid add_csr calls (not required).
2021-11-14 08:54:49 +01:00
06bae58f48
efinix_trion_t120_bga576: Do a bit a of cleanup on LPDDR3 now that working.
2021-11-12 19:43:28 +01:00
86f6d7e66b
efinix_trion_t120_bga576_dev_kit: Remove test command.
2021-11-12 18:06:11 +01:00
4e03f66fad
efinix_trion_t120_bga576_dev_kit: Remove debug, integrate LPDDR3 as done on other targets.
...
Also lower sys_clk_freq since seems to cause issue with DRAM at 100MHz: Needs to be investigated.
2021-11-12 18:04:30 +01:00
77fffda9cd
efinix_trion_t120_bga576_dev_kit: Switch to UARTBone, Add LiteScope on Pseudo-AXI, fix addressing and do first successful LPDDR3 accesses :)
2021-11-12 16:41:42 +01:00
648d38da7e
quicklogic_quickfeather: add button and GPIOIn
...
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
2021-11-12 13:21:00 +01:00
b6c5a85b98
Add initial Efinix Trion T20 MIPI Dev Kit support: CPU, ROM, RAM, UART and SPI Flash.
...
Tested with:
./efinix_trion_t20_mipi_dev_kit.py --with-spi-flash --build --load
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2021 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS built on Nov 12 2021 08:37:48
BIOS CRC passed (2bec12a3)
Migen git sha1: 7507a2b
LiteX git sha1: f679992f
--=============== SoC ==================--
CPU: VexRiscv @ 100MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 128KiB
SRAM: 8KiB
FLASH: 4096KiB
--========== Initialization ============--
Initializing W25Q32JV SPI Flash @0x00400000...
Enabling Quad mode...
First SPI Flash block erased, unable to perform freq test.
Memspeed at 0x400000 (Sequential, 4.0KiB)...
Read speed: 2.6MiB/s
Memspeed at 0x400000 (Random, 4.0KiB)...
Read speed: 1.5MiB/s
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex>
2021-11-12 08:42:10 +01:00
d6fc4b412e
efinix_trion_t120/t20_dev_kit: Switch back to 100MHz (now that timings constraints are correctly applied).
2021-11-12 07:58:51 +01:00
7ce8567d9b
targets/efinix: Bitstreams now directly generated to gateware directory.
2021-11-11 11:19:39 +01:00
855fd7e3d7
efinix_trion_t120_bga576_dev_kit: Continue LPDDR3 integration...
2021-11-10 19:40:35 +01:00
224f527baa
efinix_trion_t120_bga576_dev_kit: Go a bit further in DRAM integration.
2021-11-10 12:07:30 +01:00
040e7b3104
quicklogic_quickfeather: Use initial EOS-S3 support/integration.
2021-11-09 18:59:37 +01:00
8ce83ce92f
efinix_trion_t120_bga576_dev_kit: Add inital LPDDR3 integration (not yet working).
2021-11-09 16:13:40 +01:00
9a7e5f40b4
efinix_trion_t120_bga576_dev_kit: Add Ethernet/Etherbone support.
...
Still not fully validated: TX seems OK but RX seems shifted/corrupted.
2021-11-09 11:32:32 +01:00
ccebae6f55
targets/hyperram: Update integration.
2021-11-08 16:39:49 +01:00
184f41e61a
sipeed_tang_nano: Use PLL and 48MHz sys_clk, switch to SoCMini, add UARTBone (at 1MBauds).
...
Working correctly on hardware with updated CH552 firmware & patched litex_server...
2021-11-08 09:23:44 +01:00
8124c51dd0
Merge branch 'litex-hub:master' into master
2021-11-08 12:48:23 +07:00
d6bf2fd00e
terasic_sockit: Use standard SDRAM module from litedram
2021-11-08 12:48:03 +07:00
099d947a49
sqrl_acorn: fix vivado cfgbvs and config_voltage warnings
2021-11-07 16:18:22 +01:00
202b0e3e7d
sqrl_acorn: add option to use vivado programmer
2021-11-07 16:18:00 +01:00
f0356d8434
QMTech Daughterboard: remove xilinx specific attribute
2021-11-06 10:25:57 +07:00
a9847f15a7
qmtech_5cefa2: tuned the clock phase shift to be able to run the system at 105MHz
2021-11-06 09:58:10 +07:00
b2813cfb70
use the right DRAM chip for the QMTech Altera boards
2021-11-06 08:45:03 +07:00
ee5638a96b
qmtech-boards: fix serial so that it gets replaced by daughterboard serial correctly
2021-11-06 06:49:25 +07:00
6e7c76b71e
fairwaves_xtrx: Add clk60 (from USB PHY) as default Clk when no PCIe.
...
Fixes CI.
2021-11-05 15:22:55 +01:00
ceaaf67dfd
Add initial Fairwaves XTRX support (SoC with JTAG-UART and PCIe Gen2 X1).
2021-11-05 14:52:45 +01:00
01463a81a4
Merge pull request #287 from hansfbaier/qmtech-fixes
...
10cl006: add missing spiflash option
2021-11-05 07:11:27 +01:00
3a25af1c28
10cl006: add missing spiflash option
2021-11-05 09:57:04 +07:00
0edce3a176
Add support for QMTech 5CEFA2 board (Cyclone V)
2021-11-05 09:53:25 +07:00
a482d7f6de
targets/qmtech_xc7a35t: Use gpio_serial as serial when not mounted on daughterboard.
2021-11-04 18:52:36 +01:00
9543b5efae
marble/marble_mini: Add berkeleylab prefix.
2021-11-04 18:42:16 +01:00
5e5ae880a4
targets/litex_acorn_baseboard: Integrate WS2812/NeoPixel.
...
Tested with:
./litex_acorn_baseboard.py --cpu-type=None --uart-name=uartbone --with-ws2812 --build --csr-csv=csr.csv --load
litex_server --uart --uart-port=/dev/ttyUSBX
And test script: https://gist.github.com/enjoy-digital/c32c679a9ee4429d7f38a5ca5016a45a
2021-11-04 16:36:25 +01:00
808befec3b
Merge pull request #283 from yetifrisstlama/master
...
add Marble-board platform and target file
2021-11-04 15:20:11 +01:00
a4f8f12067
Merge pull request #284 from hansfbaier/master
...
QMTech boards: fix swapped RX/TX lines, remove double uart replacer
2021-11-04 15:18:16 +01:00
d950b3feb5
Use built-int RS232 port
...
Signed-off-by: lapd <lapd@soc.one>
2021-11-03 22:50:40 +07:00
7aa639ac0f
QMTech boards: fix swapped RX/TX lines, remove double uart replacer
2021-11-02 09:34:25 +07:00
e645eb243b
add marble board platform and target file
2021-10-28 18:41:22 +02:00
0c3f5b0fe1
prog/openocd_butterstick: Set _CHIPNAME to ecp5 (for jtag_uart/jtag_bone).
2021-10-27 17:27:07 +02:00
207afb98fc
ego1: Switch to VideoTerminal (LiteVideo is no longer provided by default with LiteX).
2021-10-27 16:29:46 +02:00
91818bc5f0
targets/gsd_butterstick/BaseSoC: Set default device to 85F (consistency with default arguments).
2021-10-26 17:01:55 +02:00
c7a91f9eab
efinix: Enable identifier on SoC (issue fixed in LiteX).
2021-10-25 19:33:49 +02:00
4bcfde8882
efinix: Avoid no_we on ROM/RAMs (no longer required).
2021-10-25 19:10:03 +02:00
d13a8d54b8
efinix_trion_txy_dev_kit: Lower sys_clk_freq for now to 50MHz, enable QSPI on T120 BGA576 dev kit.
...
Now possible with recent LiteX changes to support Tristate IOs.
2021-10-25 18:35:35 +02:00
f230eaf9bc
efinix_trion_t120_bga576: Add Tristate test code.
2021-10-25 15:01:34 +02:00
0ac0f9e75d
efinix_xyloni_dev_kit: Switch to openFPGALoader to load bitstream.
2021-10-25 12:49:48 +02:00
fc05379929
efinix_xyloni_dev_kit: Use PLL.
2021-10-25 12:16:47 +02:00
16a629269d
efinix_xyloni_dev_kit: Describe IOs in similar order than the other platforms.
2021-10-22 14:52:38 +02:00
394ea23b99
efinix_xyloni_dev_kit: Only force variant to minimal for Vexriscv.
2021-10-22 14:47:12 +02:00
75fd276dbe
efinix_xyloni_dev_kit: Increase similarities with others boards and make target very similar to iceBreaker/Fomu/TangNano4k.
2021-10-21 11:34:55 +02:00
dc1328f1a5
efinix_xyloni_dev_kit: Fix copyrights.
2021-10-21 10:12:46 +02:00
012c1d9705
efinix_trion_t20: Minor changes (move serial to platform, fix platform copyright).
2021-10-21 10:10:35 +02:00
0cf9793be5
Merge pull request #282 from AndrewD/master
...
efinix: xyloni dev board basic support
2021-10-21 10:06:25 +02:00
7525132907
litex_acorn_baseboard/video: Switch to 800x600@60Hz.
2021-10-19 16:34:28 +02:00
c548b1c1e2
efinix: xyloni dev board basic support
...
* This works: efinix_xyloni_dev_kit.py --cpu-type None --build --load --flash
* issues with SPIflash - wrong generation for tristates miso mosi for
some reason
2021-10-19 11:23:29 +11:00
a53f17380f
Merge pull request #271 from antmicro/add-data-center-board
...
WIP: boards: added datacenter DDR4 RDIMM tester board
2021-10-18 13:36:37 +02:00
a2261a1e9a
Merge pull request #280 from developandplay/master
...
Fix tang nano loopback and button
2021-10-16 09:09:39 +02:00
9645a9a310
efinix_trion_xx: append device with timing model
2021-10-16 07:36:06 +02:00
a3c7446a2b
Fix tang nano loopback and button
2021-10-16 04:35:23 +02:00
a4d330dd2c
Merge pull request #279 from mmicko/efinix_t20_flash
...
Enable writing to flash for T20
2021-10-15 18:38:08 +02:00
3730d96709
litex_acorn_baseboard: Add SPIFlash support.
2021-10-15 18:22:08 +02:00
bdf2848208
platforms/digilent_arty: Avoid commas in spiflash4x.
2021-10-15 18:22:06 +02:00
1f65d37121
Enable writing to flash for T20
2021-10-15 16:44:35 +02:00
d9638c40b8
Initial support for Efinix Trion T20 BGA256 Dev Kit
2021-10-15 12:26:15 +02:00
914e330a86
efinix_trion_t120_bga576_dev_kit: Add Flash support (Through openFPGALoader).
2021-10-15 09:38:43 +02:00
195bf176cf
efinix_trion_t120_bga576: Add SPIFlash support (X1 for now).
2021-10-14 19:16:01 +02:00
03c34e31cd
efinix_trion_t120_bga576: Add PLL to CRG and increase default sys_clk to 100MHz.
2021-10-14 15:45:26 +02:00
414b3fa636
efinix_trion_t120_bga576: Add Ethernet pins of the 2 RGMII PHYs.
2021-10-14 11:51:17 +02:00
2ea803b7d1
efinix_trion_t120_bga576: Set no_we on integrated_main_ram.
...
To allow --integrated-main-ram-size use.
2021-10-14 10:19:18 +02:00
430918756d
efinix_trion_t120_bga576: Add PMODs connectors and use USB-UART/PMOD_E as Serial.
2021-10-14 10:10:42 +02:00
36897f4646
efinix_trion_t120_bga576: Disable Identifier (crashes design) and move no_we, working.
...
./efinix_trion_t120_bga576_dev_kit.py --build --load
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2021 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS CRC passed (b23a7321)
Migen git sha1: 7507a2b
LiteX git sha1: 8316fbf1
--=============== SoC ==================--
CPU: VexRiscv @ 40MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 128KiB
SRAM: 8KiB
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex>
2021-10-14 09:39:54 +02:00
9145ff97d2
efinix_trio_t120_bga576: Add Switches pins.
2021-10-14 09:29:12 +02:00
ad773b6f2f
efinix_trion_t120_bga576: Fix argparse description.
2021-10-13 17:28:43 +02:00
6c17d76a92
targets/efinix_trion_t120_bga576: Switch to SoCCore (with CPU) and use button as reset (and AsyncResetSynchronizer).
2021-10-13 16:35:14 +02:00
5b4558c9b9
platforms/efinix_trion_t120_bga576: Add Buttons and Serial (other PMOD USB-UART).
2021-10-13 16:32:58 +02:00
a4d178a740
Add Efinix Trio T120 BGA576 Dev-Kit initial support (LedChaser).
2021-10-13 12:29:53 +02:00
83e64fbd64
targets/qmtech_10cl006: +x.
2021-10-13 12:16:41 +02:00
e29bcd30a6
litex_acorn_baseboard: Add some M2 signals and set devslp to 0.
2021-10-12 11:54:17 +02:00
a365362f5d
Rename litex_m2_baseboard to litex_acorn_baseboard and add link to repository.
2021-10-11 18:36:12 +02:00
fe08491e8d
litex_m2_baseboard: Add LCD.
2021-10-11 18:30:23 +02:00
393252ddc9
Merge pull request #277 from hansfbaier/master
...
Add support for QMTech 10CL006 board
2021-10-11 14:01:06 +02:00
79fe4a9199
Merge pull request #275 from alainlou/master
...
rz_easyfpga: cleanup and ease of use
2021-10-11 13:57:06 +02:00
2b2c7d3d68
trellisboard: Add PMOD GPIO support (for tests with MicroPython).
2021-10-11 11:33:13 +02:00
9e18d9bc34
gsd_butterstick: Remove ECLKBRIDGECS (not required).
2021-10-07 14:09:22 +02:00
d119b598c5
Add support for QMTech 10CL006 board
2021-10-05 12:06:41 +07:00
1b676f929a
cleanup and ease of use
...
- update README
- delete some unnecessary toolchain commands (copied from trenz boards)
- use minimal cpu_variant by default when vexriscv is selected
2021-10-03 13:21:45 -04:00
e8611794b4
Add initial QuickLogic QuickFeather support (Led Chaser).
...
Untested.
2021-10-01 10:58:26 +02:00
de4ad324cb
mnt_rkx7: Revert default sys_clk_freq to 100MHz.
2021-09-30 18:03:22 +02:00
1858273945
mnt_rkx7: Add SPI SDCard support.
2021-09-30 18:01:54 +02:00
05f3158311
mnt_rkx7: Increase default sys_clk_freq to 125MHz.
2021-09-30 16:22:18 +02:00
1217e94218
mnt_rkx7: Switch DDR3 to IS43TR16512B now added to LiteDRAM.
2021-09-30 15:45:40 +02:00
9bcae49629
mnt_rkx7: Add I2C (For the SiI9022A).
2021-09-30 15:33:53 +02:00
4f7c18a503
mnt_rkx7: Add Ethernet/Etherbone support.
2021-09-30 15:14:03 +02:00
84f0d715ff
mnt_rkx7: Add SDCard support.
2021-09-30 11:34:23 +02:00
31b404c42f
mng_rkx7: Add SPI Flash support.
2021-09-30 11:29:56 +02:00
df7fe5687e
Add initial MNT Reform Kintex-7 module (RKX7) support with Clk, UART and DDR3.
...
Compiles but untested on hardware.
2021-09-30 11:06:39 +02:00
82653cf66f
icebreaker/fomu: Fix SPRAM split.
2021-09-30 09:32:26 +02:00
5addd7f7d8
icebreaker/fomu: Split PSRAM in half: 64kB SRAM/64kB RAM).
...
Allows building bare metal demo and running it directly on these boards.
2021-09-29 19:33:22 +02:00
dfa572083a
Merge pull request #273 from ozbenh/wukong-v2
...
Wukong board improvements
2021-09-28 13:22:42 +02:00
228245075a
boards: added datacenter DDR4 RDIMM tester board
...
Signed-off-by: Alessandro Comodi <acomodi@antmicro.com>
2021-09-27 10:15:55 +02:00
4a52996106
Wukong board improvements
...
This adds support for v2 of the board via a --board-version argument
and a way to select the FPGA speed grade via a --speed-grade argument.
Note that the speed grade now defaults to -1. QMTech confirmed that
V1 of the board were made in two batches, one with -1 and one with -2,
while V2 of the board is all -1. So -1 is the safer default.
This also fixes the inversion of j10 and j11 and a typo in the pin
definition of jp3
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2021-09-24 12:13:56 +10:00
f18b10d1ed
Merge pull request #249 from Quiddle11/atlys
...
Initial Digilent Atlys support
2021-09-23 10:21:49 +02:00
921c300b50
digilent_atlys: Simplify/Remove entropy...
...
Build tested with ./digilent_atlys.py --with-ethernet --build.
2021-09-23 10:17:54 +02:00
1333f89ed6
rz_easyfpga: adjust SDRAM clk phase
...
- also add 1:2 rate
2021-09-22 00:26:28 -04:00
610e82d774
Add initial RZ-EasyFPGA support! ( #270 )
2021-09-21 09:55:22 +02:00
d5eea94289
sispeed_tang_nano_4k: Avoid IOStandard constraints on HyperRAM (Not present in example designs).
2021-09-20 11:46:10 +02:00
5190c9c869
sipeed_tang_nano_4k: Initial Video Out support.
...
With colorbars for now, need to free up BRAMS for Video Terminal (or finish HyperRAM support).
2021-09-20 09:32:20 +02:00
30756ce05e
targets: Update to VideoHDMIPHY.
2021-09-20 09:30:32 +02:00
7161ad18ec
sipeed_tang_nano_4k: Integrate new LiteX's GW1NSRPLL.
2021-09-20 08:40:19 +02:00
a5c5ba7652
sipeed_tang_nano_4k: Integrate HyperRam (not yet working).
2021-09-17 16:30:39 +02:00
376a836583
sipeed_tang_nano: Add SPI Flash, Enable CPU and use new external SPI Flash support from OpenFPGALoader.
...
./sipeed_tang_nano_4k.py --cpu-type=vexriscv --cpu-variant=lite --build --flash
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2021 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS built on Sep 17 2021 15:54:08
BIOS CRC passed (6cc6de6d)
Migen git sha1: a5bc262
LiteX git sha1: 46cd9c5a
--=============== SoC ==================--
CPU: VexRiscv_Lite @ 27MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 64KiB
SRAM: 8KiB
FLASH: 4096KiB
--========== Initialization ============--
Initializing W25Q32 SPI Flash @0x80000000...
SPI Flash clk configured to 13 MHz
Memspeed at 0x80000000 (Sequential, 4.0KiB)...
Read speed: 1.3MiB/s
Memspeed at 0x80000000 (Random, 4.0KiB)...
Read speed: 521.9KiB/s
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex>
2021-09-17 15:57:55 +02:00
28571308bc
sispeed_tang_nano: Add simple UART loopback test... (Not working...)
2021-09-16 19:34:48 +02:00
5955a35372
Add initial Sipeed Tang Nano support (Clk/Leds/Buttons).
2021-09-16 19:22:30 +02:00
c0aed8a727
litex_m2_baseboard: Add Video Terminal support.
2021-09-16 18:54:50 +02:00
32a9256f3b
litex_m2_baseboard: Add SDCard support.
2021-09-16 18:17:34 +02:00
0854a5d234
litex_m2_baseboard: Add Ethernet/Etherbone support.
2021-09-16 18:02:55 +02:00
8d2f75ca6d
litex_m2_baseboard: Add PMODs connectors.
2021-09-16 17:48:53 +02:00
3ad0eb6992
Add initial LiteX M2 Baseboard support with Clk/Serial/Buttons.
2021-09-16 17:44:50 +02:00
26943959b5
Merge pull request #268 from trabucayre/runber_support
...
Add runber support
2021-09-15 08:32:05 +02:00
7ccae3332d
Add runber support
2021-09-15 06:50:57 +02:00
fed36afaba
platforms/sipeed_tang_nano_4k: fix period computation
2021-09-15 06:46:29 +02:00
68fb163a27
targets: Remove spiflash mapping on targets where it's no longer useful.
2021-09-14 18:35:13 +02:00
db91eda899
linsn_rv901t.py: Update Ethernet and add Etherbone support.
2021-09-13 19:35:05 +02:00
b8373a361d
alchitry_mojo: new board
2021-09-10 02:40:31 -07:00
d4613562a8
Merge pull request #265 from trabucayre/tangNano4K_connector
...
platforms/sipeed_tang_nano_4k: add P6 and P7 connectors
2021-09-09 11:43:05 +02:00
cacb76450f
Merge pull request #264 from teknoman117/alchitry-au
...
Add Alchitry Au as new board
2021-09-09 11:42:37 +02:00
945e48ea83
platforms/sipeed_tang_nano_4k: add P6 and P7 connectors
2021-09-09 11:35:14 +02:00
8d91489756
tang_nano_4k: Add more IOs.
2021-09-09 11:23:20 +02:00
9bbdb87130
alchitry_au: new board
2021-09-09 00:03:19 -07:00
88534c6689
tang_nano_4k: Fix typo in sipeed.
2021-09-08 23:02:39 +02:00
ce52c8c5ed
beaglewire: Fix typo in qwertyembedded.
2021-09-08 21:29:29 +02:00
ecebe7e267
Add initial SiSpeed Tang Nano 4K support (Led blink only for now...).
...
./sispeed_tang_nano_4k.py --build --load
Build with Gowin EDA.
Load with OpenFPGALoader.
2021-09-08 19:36:46 +02:00
129b95f9b5
sqrl_acorn: Update pre_placement_commands with new XilinxVivadCommands.
2021-09-08 16:27:30 +02:00
7fa22a494b
arty: Switch SPI Flash rate to 1:2 (DDR) (Possible on Arty since SPI Flash's clk does not require use of STARTUPE2).
...
On the Digilent Arty, the SPI Flash's clk is connected to CCLK (that can be driven
through the STARTUPE2) but also to another generic IO that can be use to drive the
clock through DDR primitives.
2021-09-07 15:07:59 +02:00
aa2209729f
gsd_butterstick: Force uart_name to crossover when set to serial.
2021-09-02 15:23:05 +02:00
fddca1cd40
gsd_butterstick: Add SDCard (SPI & SD modes) support.
2021-09-02 14:06:09 +02:00
596f430326
gsd_butterstick: Add SPI Flash support.
2021-09-02 11:28:21 +02:00
1bbbf5b3e7
gsd_butterstick: Add SYZYGY0/1 IOs to connectors.
2021-09-02 10:26:18 +02:00
55ea71bd01
gsd_butterstick: Add initial DDR3 support.
...
Validated with:
./gsd_butterstick.py --uart-name=crossover --with-etherbone --csr-csv=csr.csv --build --load
litex_server --udp
litex_term bridge
__ _ __ _ __
/ / (_) /____ | |/_/
/ /__/ / __/ -_)> <
/____/_/\__/\__/_/|_|
Build your hardware, easily!
(c) Copyright 2012-2021 Enjoy-Digital
(c) Copyright 2007-2015 M-Labs
BIOS built on Sep 1 2021 19:09:52
BIOS CRC passed (3d349845)
Migen git sha1: 27dbf03
LiteX git sha1: 315fbe18
--=============== SoC ==================--
CPU: VexRiscv @ 75MHz
BUS: WISHBONE 32-bit @ 4GiB
CSR: 32-bit data
ROM: 128KiB
SRAM: 8KiB
L2: 8KiB
SDRAM: 524288KiB 16-bit @ 300MT/s (CL-6 CWL-5)
--========== Initialization ============--
Initializing SDRAM @0x40000000...
Switching SDRAM to software control.
Read leveling:
m0, b00: |01110000| delays: 02+-01
m0, b01: |00000000| delays: -
m0, b02: |00000000| delays: -
m0, b03: |00000000| delays: -
best: m0, b00 delays: 02+-01
m1, b00: |01110000| delays: 02+-01
m1, b01: |00000000| delays: -
m1, b02: |00000000| delays: -
m1, b03: |00000000| delays: -
best: m1, b00 delays: 02+-01
Switching SDRAM to hardware control.
Memtest at 0x40000000 (2.0MiB)...
Write: 0x40000000-0x40200000 2.0MiB
Read: 0x40000000-0x40200000 2.0MiB
Memtest OK
Memspeed at 0x40000000 (Sequential, 2.0MiB)...
Write speed: 13.6MiB/s
Read speed: 15.6MiB/s
--============== Boot ==================--
Booting from serial...
Press Q or ESC to abort boot completely.
sL5DdSMmkekro
Timeout
No boot medium found
--============= Console ================--
litex>
2021-09-01 19:21:16 +02:00
1f25a98476
butterstick: Add Ethernet/Etherbone support (UART crossover working over Etherbone).
2021-09-01 18:03:13 +02:00
1f149ece6b
Add intial ButterStick support (with just Clk, Buttons and Leds).
2021-09-01 17:33:54 +02:00
74c2178150
lattice_crosslink_nx_evn: don't set MASTER_SPI_PORT=SERIAL
...
Setting MASTER_SPI_PORT=SERIAL causes the SPI flash pins to be reserved
for use by the sysCONFIG logic, and prevents user logic from assigning
them. This made it impossible to have a Litex design which accesses the
SPI flash on this board.
Remove the setting, so that we get the default behaviour which permits
user logic to assign these pins. In the unlikely event that someone
needs the pins to stay reserved for sysCONFIG after configuration (I'm
not sure why this would be needed) they could explicitly add this
command in their design.
2021-09-01 18:47:17 +10:00
4731c500fb
Merge pull request #258 from danc86/clnexevn-device-arg
...
lattice_crosslink_nx_evn: allow specifying the FPGA device
2021-09-01 10:22:42 +02:00
ce254208ff
beaglewire: Review/Cleanup for consistency with other targets.
...
- Now uses regular UART.
- Build tested with: ./quertyembedded_beaglewire.py --cpu-type=serv --build
- Can still be build with Crossover UART with --uart-name=crossover+bridge.
2021-09-01 10:18:11 +02:00
35df77258a
beaglewire: Rename to quertyembedded_beaglewire.
2021-09-01 09:36:09 +02:00
1e1f6a476d
Merge pull request #254 from ombhilare999/master
...
beaglewire platform and target added
2021-09-01 09:33:07 +02:00
4a18951651
tul_pynq_z2: Fix copyrights, remove PS7 part for now.
2021-09-01 08:50:56 +02:00
54c777a49c
Merge pull request #252 from developandplay/PYNQ-Z2
...
WIP: Initial PYNQ Z2 support
2021-09-01 08:46:44 +02:00
6a08a7973c
Merge pull request #251 from niw/fix_orangecrab_feather_spi_pad_name
...
FIX: OrangeCrab Feather SPI pad name
2021-08-31 18:59:09 +02:00
8f1c15bdb8
ebaz4205: Remove PS7 support for now (since untested and we'll avoid the .xci in LiteX-Boards repository).
2021-08-31 18:56:47 +02:00
781d83bab6
Add support for EBAZ4205 'Development' Board
...
Usage:
```
./ebaz4205.py --cpu-type=vexriscv --build --load
```
```
$ pwd
litex-boards/litex_boards/targets
```
Tip: Use `GTKTerm` to connect to /dev/ttyUSB0 (usually) and interact
with the LiteX BIOS.
References:
- https://github.com/fusesoc/blinky#ebaz4205-development-board
- https://github.com/olofk/serv/#ebaz4205-development-board
- https://github.com/xjtuecho/EBAZ4205#ebaz4205
- https://github.com/nmigen/nmigen-boards/pull/180 (merged)
- https://github.com/olofk/corescore/pull/33
- The existing 'Zybo Z7' example
Note: The `PS7` stuff remains untested via LiteX for now.
2021-08-31 18:54:49 +02:00
fc78c96444
FIX: OrangeCrab Feather SPI pad name
...
**Problems**
`SPIMaster` pad names are `clk`, `cs_n`, `mosi`, and `miso`.
However, `feather_spi` is using `sck` instead of `clk`, therefore
it is not able to use as-is for `SPIMaster`, for example,
with `add_spi` on Linux On LiteX VexRiscv.
**Solution**
In fact, `spisdcard` and other SPI related pad names are
using `clk`, only `feather_spi` is using `sck`.
Therefore, rename `sck` to `clk`.
2021-08-29 17:59:45 -07:00
b017a33f2b
targets: Fix SPI Flash mapping on target supporting --with-spi-flash.
2021-08-23 18:05:40 +02:00
cc9e39286a
lattice_crosslink_nx_evn: allow specifying the FPGA device
...
This board is documented as having the LIFCL-40-9BG400C part, but some
versions of the board exist which were fitted with LIFCL-40-8BG400CES,
an engineering sample part. The distinction is important because the
engineering sample requires a different device ID to be embedded in the
bitstream. If you try to build a bitstream for LIFCL-40-9BG400C and load
it onto LIFCL-40-8BG400CES the configuration fails (indicated by the red
"INITN" LED on this board).
Accept --device to allow the user to specify which FPGA part their board
has.
2021-08-17 18:30:03 +10:00
db9c98b28a
beaglewire platform and target added
2021-08-16 20:14:45 +05:30
22e823d756
Initial PYNQ Z2 support
2021-08-13 16:23:39 +02:00
b77b1514ce
Merge pull request #250 from david-sawatzke/fullmemwe
...
colorlight_5a_75x: Disable full_memory_we for l2 cache by default
2021-08-11 09:53:47 +02:00
9f5e8d4864
colorlight_5a_75x: Disable full_memory_we for l2 cache by default
...
Leads to an increase in DP16KD, first noticed in
https://github.com/enjoy-digital/liteeth/issues/70 .
With full_mem_we:
```
Info: DP16KD: 41/ 56 73%
```
Without:
```
Info: DP16KD: 29/ 56 51%
```
2021-08-08 14:37:46 +02:00
b81309401e
Initial Digilent Atlys support
2021-08-06 13:24:19 +02:00
615b97e205
tinyfpga_bx: Switch to LiteSPI.
2021-07-30 08:18:15 +02:00
90fcaec287
targets/radiona_ulx3s: Switch to LiteSPI.
2021-07-30 08:10:52 +02:00
fdf94b95c9
muselabe_icesugar/SPIFlash: Disable Master (to avoid wasting resources on this small FPGA).
2021-07-29 19:59:22 +02:00
218e830fbf
muselab_icesugar_pro: Switch to LiteSPI.
2021-07-29 19:58:13 +02:00
569c20ab86
muselab_icesugar: Switch to LiteSPI.
2021-07-29 19:55:32 +02:00
8df797c716
lattice_ice40up5k_evn: Switch to LiteSPI.
2021-07-29 19:50:36 +02:00
5e8c29d657
colorlight_i5: Switch to LiteSPI.
2021-07-29 19:47:41 +02:00
35ba3d9bc3
targets: Remove old call to add_spi_flash on targets now using LiteSPI (we'll find it with gitk is required).
2021-07-29 11:55:10 +02:00
54cee05986
#248 : Minor cleanup.
2021-07-28 18:20:42 +02:00
a41fbea5e6
Merge pull request #248 from JosephBushagour/jbushagour_fomu_spi_options
...
Add option for different Fomu SPI ICs.
2021-07-28 18:18:12 +02:00
99ff82c75a
xilinx_alveo_u280: Add more IOs and enable HBM2.
2021-07-28 18:11:49 +02:00
7b3dce65c1
Add option for different Fomu SPI chips.
...
Signed-off-by: Joey Bushagour <jbushagour@google.com>
2021-07-28 10:34:02 -05:00
401568c54e
digilent_arty_s7: Add SPI Flash.
2021-07-28 14:22:26 +02:00
64eadd8012
hackaday_hadbadge: Lower PLL's PFD Min from 10MHz to 8MHz.
...
This is now required since ECP5PLL now checks that PFD is in required range.
2021-07-28 12:25:17 +02:00
6ce5db1b90
qmtech_xc7a35t: Fix default build.
2021-07-28 12:23:24 +02:00
1f4383475a
decklink_intensity_pro_4k: Fix default build.
2021-07-28 12:23:12 +02:00
3e8b6677e9
platforms: Make sure all platforms have a default Clk. (To be able to run simple target).
2021-07-28 12:03:06 +02:00
4e2b596ab3
digilent_arty/qmtech_xc7a35t: Rename --with-mapped-flash to --with-spi-flash.
2021-07-28 11:21:51 +02:00
fa3cc9b753
kosagi_fomu/spiflash: Switch to READ_1_1_4.
2021-07-28 11:10:34 +02:00
1118b09350
trenz_tec0117: Switch to LiteSPI.
2021-07-28 10:34:17 +02:00
9065cfa75d
kosagi_fomu: Switch to LiteSPI.
2021-07-27 19:55:04 +02:00
b3e7dbfd30
qmtech_xc7a35t: LiteSPI integration now provided by LiteX.
2021-07-27 19:39:50 +02:00
55ba0591df
targets: Remove SpiFlash imports (Obsolete since integration is provided by LiteX).
2021-07-27 19:35:19 +02:00
1c52e6b8fb
targets/digilent_arty/spiflash: LiteSPI integration now provided by LiteX.
2021-07-27 19:30:38 +02:00
15b5aec23f
1bitsquared_icebreaker_bitsy: Also switch to LiteSPI.
2021-07-27 19:27:28 +02:00
959780f372
1bitsquared_icebreaker: Switch to LiteSPI (with integration now done by LiteX).
...
Keep the old add_spi_flash call commented for now just in case we need to compare/test it.
2021-07-27 19:23:26 +02:00
533d25e845
1bitsquared_icebreaker: Enable LiteSPI Master but reduce FIFO depth to reduce resource usage.
...
Already better regarding resource usage:
Info: ICESTORM_LC: 2938/ 5280 55%
Info: ICESTORM_RAM: 2/ 30 6%
Info: SB_IO: 15/ 96 15%
Info: SB_GB: 8/ 8 100%
Info: ICESTORM_PLL: 1/ 1 100%
Info: SB_WARMBOOT: 0/ 1 0%
Info: ICESTORM_DSP: 0/ 8 0%
Info: ICESTORM_HFOSC: 0/ 1 0%
Info: ICESTORM_LFOSC: 0/ 1 0%
Info: SB_I2C: 0/ 2 0%
Info: SB_SPI: 0/ 2 0%
Info: IO_I3C: 0/ 2 0%
Info: SB_LEDDA_IP: 0/ 1 0%
Info: SB_RGBA_DRV: 0/ 1 0%
Info: ICESTORM_SPRAM: 4/ 4 100%
2021-07-27 17:38:25 +02:00
12fb315e09
1bitsquared_icebreaker: Disable LiteSPI Master.
...
Requires 80e9d2cea9
2021-07-27 17:00:55 +02:00
Florent Kermarrec
Dave Berkeley
Franck Jullien
inc
Andrew Gillham
Raptor Engineering Development Team
Ilia Sergachev
Gwenhael Goavec-Merou
hubmartin
Sergiu Mosanu
Arusekk
Ben Stobbs
Jevin Sweval
Victor Suarez Rovere
Tim Callahan
Icenowy Zheng
vacajk
Gabriel Somlo
Bastian Löher
Robert Wilbrandt
Rakesh Peter
Alastair M. Robinson
Karol Gugala
Matthew Brooks
Primesh
derekmulcahy
Derek Mulcahy
Franck Jullien
Marek Materzok
Ilia Sergachev
Greg Davill
Miodrag Milanovic
Alessandro Comodi
Hans Baier
Ilia Sergachev
lapd
Michael Betz
Andrew Dennison
Martin Troiber
alainlou
Benjamin Herrenschmidt
Nathaniel R. Lewis
Dan Callaghan
Dhiru Kholia
Yoshimasa Niwa
ombhilare999
David Sawatzke
MV
Joey Bushagour